As remember that there is a fault in the tuner register read function in
ds3000.c file.
It will cause the read back value wrong.
ds3000.c file,
static int ds3000_tuner_readreg(struct ds3000_state *state, u8 reg)
{
.......
ds3000_writereg(state, 0x03, 0x12);
.......
}
in DVBSky code, m88ds3103.c file,
static int m88ds3103_tuner_readreg(struct m88ds3103_state *state, u8 reg)
{
........
m88ds3103_writereg(state, 0x03, 0x11);
........
}
DVBSky code can read back the value correctly.
As known that m88ds3103.c also supports the older tuner(m88ts2020) and
demodulator(m88ds3000/3002).
2012-08-31 16:18:38 nibble....@gmail.com
>On 08/30/2012 06:21 PM, Rémi Cardona wrote:
>> Hi Antti,
>>
>> On 08/30/2012 03:39 PM, Antti Palosaari wrote:
>>> As I understand firmware downloading failure is coming from the fact
>>> that register read fails => fails to detect if firmware is already
>>> running or not.
>>
>> Well we actually see 2 cases:
>>
>> - the register read failure (when ds3000_readreg() returns negative
>> values). This case is fairly rare, and no changes we've done to the
>> driver allowed us to make those cards work.
>
>hmm, looks like ds3000_readreg() logic is still a little bit broken. It
>checks count of sent messages and compares it to 2. But if I2C-adapter
>sends only 1 message or 3 (which should not be possible) function return
>that count instead of -EREMOTEIO. OK, quite rare situation, but one
>point more to fail if I2C-adapter has also bug.
>
>But that happens for return value 0 too. Could it be the issue?
>I2C-adapter returns 0 for some reason? Bug in I2C-adapter with bug in
>ds3000_readreg() implementation?
>
>> - the register read returning 0. Looking at the current code, it looks
>> like the 0xb2 register is supposed to mean that a firmware is loaded.
>> This case is fairly common: we've had many cards randomly saying that a
>> firmware was loaded when none had been. Often, a simple reboot will do
>> the trick. But sometimes, forcing the firmware upload (ie, bypassing the
>> 0xb2 register check) allows the stubborn cards to function properly.
>>
>>> Original behavior to expect firmware is loaded and running when register
>>> read fails is very stupid and your fix seems much better.
>>
>> Well, this patch should not really change the behavior. It just
>> propagates register read errors to ds3000_initfe(). It'll just fail earlier.
>>
>>> So first priority should be try fix that issue with register read. Is it
>>> coming from the USB stack (eg. error 110 timeout) or some other error
>>> coming from the fact chip answers wrong?
>>
>> The cards we're using are PCIe (and not the ones with an embedded USB
>> controller).
>
>The idea of my question was to ask where those errors are coming from (I
>spoke mistakenly about USB because I usually play with USB devices).
>
>You basically see two different kind of errors, 1) bus communication
>fails, eg. usb timeouts. 2) chips returns error status. Later cases the
>error could come from the this could come from the firmware if chip uses
>firmware or from the silicon. It could be from the I2C-adapter firmware.
>
>>> Do you see other register I/O failing too?
>>
>> I'll see if I can get you an answer for that, since the cards are
>> shipped with the appliance we send to our customers. Remote debugging is
>> somewhat tricky.
>>
>>> Does adding few usec sleep help?
>>
>> I'm not quite sure where to add those sleeps. In the register
>> reading/writing functions? 10us? 100us?
>
>Add sleep after the each operation. Good place to add sleep is
>I2C-adapter. I2C-adapters usually supports two different operations,
>write and read + write using repeated START condition. Former us used
>typically for register write and later for register read.
>
>500us is good choice. If it is only that one register read which causes
>problems, how about repeating it?
>
>>
>> Many thanks
>>
>> Rémi
>>
>
>
>--
>http://palosaari.fi/
>--
>To unsubscribe from this list: send the line "unsubscribe linux-media" in
>the body of a message to majord...@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
N�����r��y����b�X��ǧv�^�){.n�+����{���bj)����w* jg��� �����ݢj/���z�ޖ��2�ޙ����&�)ߡ�a���� �G���h��j:+v���w��٥
