Hi all Version 5 of this RFC is a result of a discussion of its version 4, which took place during the recent Linux Plumbers conference in San Diego. Changes are:
(1) remove bus-width properties from device (bridge and client) top level. This has actually already been decided upon during our discussions with Sylwester, I just forgot to actually remove them, sorry. (2) links are now grouped under "ports." This should help better describe device connection topology by making clearer, which interfaces links are attached to. (help needed: in my notes I see "port" optional if only one port is present, but I seem to remember, that the final decision was - make ports compulsory for uniformity. Which one is true?) (3) "videolink" is renamed to just "link." (4) "client" is renamed to "remote" and is now used on both sides of links. (5) clock-names in clock consumer nodes (e.g., camera sensors) should reflect clock input pin names from respective datasheets (6) also serial bus description should be placed under respective link nodes. (7) reference remote link DT nodes in "remote" properties, not to the parent. (8) use standard names for "SoC-external" (e.g., i2c) devices on their respective busses. "Sensor" has been proposed, maybe "camera" is a better match though. Thanks Guennadi --- Guennadi Liakhovetski, Ph.D. Freelance Open-Source Software Developer http://www.open-technology.de/ // Describe an imaginary configuration: a CEU serving either a parallel ov7725 // sensor, or a serial imx074 sensor, connected over a CSI-2 SoC interface ceu0: ceu@0xfe910000 { compatible = "renesas,sh-mobile-ceu"; reg = <0xfe910000 0xa0>; interrupts = <0x880>; mclk: master_clock { compatible = "renesas,ceu-clock"; #clock-cells = <1>; clock-frequency = <50000000>; /* max clock frequency */ clock-output-names = "mclk"; }; ... port@0 { #address-cells = <1>; #size-cells = <0>; ov772x_1_1: link@1 { reg = <1>; /* local pad # */ remote = <&ceu0_1>; /* remote phandle and pad # */ bus-width = <8>; /* used data lines */ data-shift = <0>; /* lines 7:0 are used */ /* If [hv]sync-active are missing, embedded bt.605 sync is used */ hsync-active = <1>; /* active high */ vsync-active = <1>; /* active high */ pclk-sample = <1>; /* rising */ }; csi2_0: link@0 { reg = <0>; remote = <&ceu0_2>; immutable; }; }; }; i2c0: i2c@0xfff20000 { ... ov772x_1: camera@0x21 { compatible = "omnivision,ov772x"; reg = <0x21>; vddio-supply = <®ulator1>; vddcore-supply = <®ulator2>; clock-frequency = <20000000>; clocks = <&mclk 0>; clock-names = "xclk"; ... port { /* With 1 link per port no need in addresses */ ceu0_1: link@0 { bus-width = <8>; remote = <&ov772x_1_1>; hsync-active = <1>; hsync-active = <0>; /* who came up with an inverter here?... */ pclk-sample = <1>; }; }; }; imx074: camera@0x1a { compatible = "sony,imx074"; reg = <0x1a>; vddio-supply = <®ulator1>; vddcore-supply = <®ulator2>; clock-frequency = <30000000>; /* shared clock with ov772x_1 */ clocks = <&mclk 0>; clock-names = "sysclk"; /* assuming this is the name in the datasheet */ ... port { csi2_1: link@0 { clock-lanes = <0>; data-lanes = <1>, <2>; remote = <&imx074_1>; }; }; }; ... }; csi2: csi2@0xffc90000 { compatible = "renesas,sh-mobile-csi2"; reg = <0xffc90000 0x1000>; interrupts = <0x17a0>; #address-cells = <1>; #size-cells = <0>; ... port { compatible = "renesas,csi2c"; /* one of CSI2I and CSI2C */ reg = <1>; /* CSI-2 PHY #1 of 2: PHY_S, PHY_M has port address 0, is unused */ imx074_1: link@1 { client = <&imx074 0>; clock-lanes = <0>; data-lanes = <2>, <1>; remote = <&csi2_1>; }; }; port { reg = <2>; /* port 2: link to the CEU */ ceu0_2: link@0 { immutable; remote = <&csi2_0>; }; }; }; -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
