Am Montag, den 17.06.2013, 16:59 +0200 schrieb Philipp Zabel:
> This patch enables decoding of h.264 and mpeg4 streams on CODA7541.
> Queued output buffers are immediately copied into the bitstream
> ringbuffer. A device_run can be scheduled whenever there is either
> enough compressed bitstream data, or the CODA is in stream end mode.
>
> Each successful device_run, data is read from the bitstream ringbuffer
> and a frame is decoded into a free internal framebuffer. Depending on
> reordering, a possibly previously decoded frame is marked as display
> frame, and at the same time the display frame from the previous run
> is copied out into a capture buffer by the rotator hardware.
>
> The dequeued capture buffers are counted to send the EOS signal to
> userspace with the last frame. When userspace sends the decoder stop
> command or enqueues an empty output buffer, the stream end flag is
> set to allow decoding the remaining frames in the bitstream
> ringbuffer.
>
> The enum_fmt/try_fmt functions return fixed capture buffer sizes
> while the output queue is streaming, to allow better autonegotiation
> in userspace.
>
> A per-context buffer mutex is used to lock the picture run against
> buffer dequeueing: if a job gets queued, then streamoff dequeues
> the last buffer, and then device_run is called, bail out. For that
> the interrupt handler has to be threaded.
>
> Signed-off-by: Philipp Zabel <[email protected]>
> ---
> drivers/media/platform/coda.c | 785
> ++++++++++++++++++++++++++++++++++++++----
> drivers/media/platform/coda.h | 84 +++++
> 2 files changed, 811 insertions(+), 58 deletions(-)
>
> diff --git a/drivers/media/platform/coda.c b/drivers/media/platform/coda.c
> index e8b3708..16f1726 100644
> --- a/drivers/media/platform/coda.c
> +++ b/drivers/media/platform/coda.c
[...]
> @@ -938,6 +1185,8 @@ static void coda_device_run(void *m2m_priv)
> /* 1 second timeout in case CODA locks up */
> schedule_delayed_work(&dev->timeout, HZ);
>
> + if (ctx->inst_type == CODA_INST_DECODER)
> + coda_kfifo_sync_to_device_full(ctx);
> coda_command_async(ctx, CODA_COMMAND_PIC_RUN);
> }
>
> @@ -963,6 +1212,15 @@ static int coda_job_ready(void *m2m_priv)
> return 0;
> }
>
> + if (ctx->prescan_failed ||
> + ((coda_get_bitstream_payload(ctx) < 512) &&
> + !(ctx->bit_stream_param & CODA_BIT_STREAM_END_FLAG))) {
> + v4l2_dbg(1, coda_debug, &ctx->dev->v4l2_dev,
> + "%d: not ready: not enough bitstream data.\n",
This of course is only valid for decoder contexts:
--- a/drivers/media/platform/coda.c
+++ b/drivers/media/platform/coda.c
@@ -1618,7 +1618,8 @@ static int coda_job_ready(void *m2m_priv)
}
if (ctx->prescan_failed ||
- ((coda_get_bitstream_payload(ctx) < 512) &&
+ ((ctx->inst_type == CODA_INST_DECODER) &&
+ (coda_get_bitstream_payload(ctx) < 512) &&
!(ctx->bit_stream_param & CODA_BIT_STREAM_END_FLAG))) {
v4l2_dbg(1, coda_debug, &ctx->dev->v4l2_dev,
"%d: not ready: not enough bitstream data.\n",
> + ctx->idx);
> + return 0;
> + }
> +
> if (ctx->aborting) {
> v4l2_dbg(1, coda_debug, &ctx->dev->v4l2_dev,
> "not ready: aborting\n");
[...]
regards
Philipp
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html