* Kishon Vijay Abraham I <kis...@ti.com> [130717 23:53]:
> Updated the usb_otg_hs dt data to include the *phy* and *phy-names*
> binding in order for the driver to use the new generic PHY framework.
> Also updated the Documentation to include the binding information.
> The PHY binding information can be found at
> Documentation/devicetree/bindings/phy/phy-bindings.txt
>
> Signed-off-by: Kishon Vijay Abraham I <kis...@ti.com>
> Acked-by: Felipe Balbi <ba...@ti.com>
> Reviewed-by: Sylwester Nawrocki <s.nawro...@samsung.com>
In general the .dts changes should be separate to avoid pointless
merge conflicts. But sounds like things will stop working for
USB unless we do it like this so:
Acked-by: Tony Lindgren <t...@atomide.com>
> ---
> Documentation/devicetree/bindings/usb/omap-usb.txt | 5 +++++
> Documentation/devicetree/bindings/usb/usb-phy.txt | 6 ++++++
> arch/arm/boot/dts/omap3-beagle-xm.dts | 2 ++
> arch/arm/boot/dts/omap3-evm.dts | 2 ++
> arch/arm/boot/dts/omap3-overo.dtsi | 2 ++
> arch/arm/boot/dts/omap4.dtsi | 3 +++
> arch/arm/boot/dts/twl4030.dtsi | 1 +
> 7 files changed, 21 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt
> b/Documentation/devicetree/bindings/usb/omap-usb.txt
> index 57e71f6..825790d 100644
> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
> @@ -19,6 +19,9 @@ OMAP MUSB GLUE
> - power : Should be "50". This signifies the controller can supply up to
> 100mA when operating in host mode.
> - usb-phy : the phandle for the PHY device
> + - phys : the phandle for the PHY device (used by generic PHY framework)
> + - phy-names : the names of the PHY corresponding to the PHYs present in the
> + *phy* phandle.
>
> Optional properties:
> - ctrl-module : phandle of the control module this glue uses to write to
> @@ -33,6 +36,8 @@ usb_otg_hs: usb_otg_hs@4a0ab000 {
> num-eps = <16>;
> ram-bits = <12>;
> ctrl-module = <&omap_control_usb>;
> + phys = <&usb2_phy>;
> + phy-names = "usb2-phy";
> };
>
> Board specific device node entry
> diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt
> b/Documentation/devicetree/bindings/usb/usb-phy.txt
> index 61496f5..c0245c8 100644
> --- a/Documentation/devicetree/bindings/usb/usb-phy.txt
> +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
> @@ -5,6 +5,8 @@ OMAP USB2 PHY
> Required properties:
> - compatible: Should be "ti,omap-usb2"
> - reg : Address and length of the register set for the device.
> + - #phy-cells: determine the number of cells that should be given in the
> + phandle while referencing this phy.
>
> Optional properties:
> - ctrl-module : phandle of the control module used by PHY driver to power on
> @@ -16,6 +18,7 @@ usb2phy@4a0ad080 {
> compatible = "ti,omap-usb2";
> reg = <0x4a0ad080 0x58>;
> ctrl-module = <&omap_control_usb>;
> + #phy-cells = <0>;
> };
>
> OMAP USB3 PHY
> @@ -25,6 +28,8 @@ Required properties:
> - reg : Address and length of the register set for the device.
> - reg-names: The names of the register addresses corresponding to the
> registers
> filled in "reg".
> + - #phy-cells: determine the number of cells that should be given in the
> + phandle while referencing this phy.
>
> Optional properties:
> - ctrl-module : phandle of the control module used by PHY driver to power on
> @@ -39,4 +44,5 @@ usb3phy@4a084400 {
> <0x4a084c00 0x40>;
> reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> ctrl-module = <&omap_control_usb>;
> + #phy-cells = <0>;
> };
> diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts
> b/arch/arm/boot/dts/omap3-beagle-xm.dts
> index afdb164..533b2da 100644
> --- a/arch/arm/boot/dts/omap3-beagle-xm.dts
> +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
> @@ -144,6 +144,8 @@
> &usb_otg_hs {
> interface-type = <0>;
> usb-phy = <&usb2_phy>;
> + phys = <&usb2_phy>;
> + phy-names = "usb2-phy";
> mode = <3>;
> power = <50>;
> };
> diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
> index 7d4329d..4134dd0 100644
> --- a/arch/arm/boot/dts/omap3-evm.dts
> +++ b/arch/arm/boot/dts/omap3-evm.dts
> @@ -70,6 +70,8 @@
> &usb_otg_hs {
> interface-type = <0>;
> usb-phy = <&usb2_phy>;
> + phys = <&usb2_phy>;
> + phy-names = "usb2-phy";
> mode = <3>;
> power = <50>;
> };
> diff --git a/arch/arm/boot/dts/omap3-overo.dtsi
> b/arch/arm/boot/dts/omap3-overo.dtsi
> index 8f1abec..a461d2f 100644
> --- a/arch/arm/boot/dts/omap3-overo.dtsi
> +++ b/arch/arm/boot/dts/omap3-overo.dtsi
> @@ -76,6 +76,8 @@
> &usb_otg_hs {
> interface-type = <0>;
> usb-phy = <&usb2_phy>;
> + phys = <&usb2_phy>;
> + phy-names = "usb2-phy";
> mode = <3>;
> power = <50>;
> };
> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> index 22d9f2b..1e8e2fe 100644
> --- a/arch/arm/boot/dts/omap4.dtsi
> +++ b/arch/arm/boot/dts/omap4.dtsi
> @@ -520,6 +520,7 @@
> compatible = "ti,omap-usb2";
> reg = <0x4a0ad080 0x58>;
> ctrl-module = <&omap_control_usb>;
> + #phy-cells = <0>;
> };
> };
>
> @@ -658,6 +659,8 @@
> interrupt-names = "mc", "dma";
> ti,hwmods = "usb_otg_hs";
> usb-phy = <&usb2_phy>;
> + phys = <&usb2_phy>;
> + phy-names = "usb2-phy";
> multipoint = <1>;
> num-eps = <16>;
> ram-bits = <12>;
> diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
> index b3034da..ce4cd6f 100644
> --- a/arch/arm/boot/dts/twl4030.dtsi
> +++ b/arch/arm/boot/dts/twl4030.dtsi
> @@ -80,6 +80,7 @@
> usb1v8-supply = <&vusb1v8>;
> usb3v1-supply = <&vusb3v1>;
> usb_mode = <1>;
> + #phy-cells = <0>;
> };
>
> twl_pwm: pwm {
> --
> 1.7.10.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
