Dear Gueannadi,
On 10/5/2015 1:04 AM, Guennadi Liakhovetski wrote:
Even simpler:
On Sun, 4 Oct 2015, Guennadi Liakhovetski wrote:
Hi Josh,
On Tue, 22 Sep 2015, Josh Wu wrote:
we need to configure the YCC_SWAP bits in ISI_CFG2 according to current
sensor output and Atmel ISI output format.
Current there are two cases Atmel ISI supported:
1. Atmel ISI outputs YUYV format.
This case we need to setup YCC_SWAP according to sensor output
format.
2. Atmel ISI output a pass-through formats, which means no swap.
Just setup YCC_SWAP as default with no swap.
Signed-off-by: Josh Wu <josh...@atmel.com>
---
drivers/media/platform/soc_camera/atmel-isi.c | 43 ++++++++++++++++++++-------
1 file changed, 33 insertions(+), 10 deletions(-)
diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
b/drivers/media/platform/soc_camera/atmel-isi.c
index 45e304a..df64294 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -103,13 +103,41 @@ static u32 isi_readl(struct atmel_isi *isi, u32 reg)
return readl(isi->regs + reg);
}
+static u32 setup_cfg2_yuv_swap(struct atmel_isi *isi,
+ const struct soc_camera_format_xlate *xlate)
+{
This function will be called only for the four media codes from the
switch-case statement below, namely for
MEDIA_BUS_FMT_VYUY8_2X8
MEDIA_BUS_FMT_UYVY8_2X8
MEDIA_BUS_FMT_YVYU8_2X8
MEDIA_BUS_FMT_YUYV8_2X8
+ /* By default, no swap for the codec path of Atmel ISI. So codec
+ * output is same as sensor's output.
+ * For instance, if sensor's output is YUYV, then codec outputs YUYV.
+ * And if sensor's output is UYVY, then codec outputs UYVY.
+ */
+ u32 cfg2_yuv_swap = ISI_CFG2_YCC_SWAP_DEFAULT;
Then this ISI_CFG2_YCC_SWAP_DEFAULT will only hold for
MEDIA_BUS_FMT_YUYV8_2X8? Why don't you just add one more case below? Don't
think this initialisation is really justified.
+
+ if (xlate->host_fmt->fourcc == V4L2_PIX_FMT_YUYV) {
+ /* all convert to YUYV */
+ switch (xlate->code) {
+ case MEDIA_BUS_FMT_VYUY8_2X8:
+ cfg2_yuv_swap = ISI_CFG2_YCC_SWAP_MODE_3;
+ break;
Why don't you just return the result value here directly? Then you don't
need the variable at all
yes, This sounds good. I'll take rid of the cfg2_yuv_swap variable. Thanks.
Best Regards,
Josh Wu
+ case MEDIA_BUS_FMT_UYVY8_2X8:
+ cfg2_yuv_swap = ISI_CFG2_YCC_SWAP_MODE_2;
+ break;
+ case MEDIA_BUS_FMT_YVYU8_2X8:
+ cfg2_yuv_swap = ISI_CFG2_YCC_SWAP_MODE_1;
+ break;
+ }
+ }
+
+ return cfg2_yuv_swap;
+}
+
static void configure_geometry(struct atmel_isi *isi, u32 width,
- u32 height, u32 code)
+ u32 height, const struct soc_camera_format_xlate *xlate)
{
u32 cfg2;
/* According to sensor's output format to set cfg2 */
- switch (code) {
+ switch (xlate->code) {
default:
/* Grey */
case MEDIA_BUS_FMT_Y8_1X8:
@@ -117,16 +145,11 @@ static void configure_geometry(struct atmel_isi *isi, u32
width,
break;
/* YUV */
case MEDIA_BUS_FMT_VYUY8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_3 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_UYVY8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_2 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_YVYU8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_1 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_YUYV8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_DEFAULT | ISI_CFG2_COL_SPACE_YCbCr;
+ cfg2 = ISI_CFG2_COL_SPACE_YCbCr |
+ setup_cfg2_yuv_swap(isi, xlate);
break;
/* RGB, TODO */
}
I would move this switch-case completely inside setup_cfg2_yuv_swap().
Just do
cfg2 = setup_cfg2_yuv_swap(isi, xlate);
and handle the
case MEDIA_BUS_FMT_Y8_1X8:
in the function too. These two switch-case statements really look
redundant.
@@ -407,7 +430,7 @@ static int start_streaming(struct vb2_queue *vq, unsigned
int count)
isi_writel(isi, ISI_INTDIS, (u32)~0UL);
configure_geometry(isi, icd->user_width, icd->user_height,
- icd->current_fmt->code);
+ icd->current_fmt);
spin_lock_irq(&isi->lock);
/* Clear any pending interrupt */
--
1.9.1
Thanks
Guennadi
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
