Hi Ulrich,
Thank you for the patch.
On Friday 11 December 2015 17:04:28 Ulrich Hecht wrote:
> When probed from device tree, the i2c client driver can handle the
> interrupt on its own.
>
> Signed-off-by: Ulrich Hecht <ulrich.hecht+rene...@gmail.com>
> ---
> drivers/media/i2c/adv7604.c | 24 ++++++++++++++++++++++--
> 1 file changed, 22 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
> index c2df7e8..129009f 100644
> --- a/drivers/media/i2c/adv7604.c
> +++ b/drivers/media/i2c/adv7604.c
> @@ -31,6 +31,7 @@
> #include <linux/gpio/consumer.h>
> #include <linux/hdmi.h>
> #include <linux/i2c.h>
> +#include <linux/interrupt.h>
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/slab.h>
> @@ -1971,6 +1972,16 @@ static int adv76xx_isr(struct v4l2_subdev *sd, u32
> status, bool *handled) return 0;
> }
>
> +static irqreturn_t adv76xx_irq_handler(int irq, void *devid)
> +{
> + struct adv76xx_state *state = devid;
> + bool handled;
> +
> + adv76xx_isr(&state->sd, 0, &handled);
> +
> + return handled ? IRQ_HANDLED : IRQ_NONE;
> +}
> +
> static int adv76xx_get_edid(struct v4l2_subdev *sd, struct v4l2_edid *edid)
> {
> struct adv76xx_state *state = to_state(sd);
> @@ -2833,8 +2844,7 @@ static int adv76xx_parse_dt(struct adv76xx_state
> *state) state->pdata.op_656_range = 1;
> }
>
> - /* Disable the interrupt for now as no DT-based board uses it. */
> - state->pdata.int1_config = ADV76XX_INT1_CONFIG_DISABLED;
> + state->pdata.int1_config = ADV76XX_INT1_CONFIG_ACTIVE_LOW;
>
> /* Use the default I2C addresses. */
> state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42;
> @@ -3224,6 +3234,16 @@ static int adv76xx_probe(struct i2c_client *client,
> v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name,
> client->addr << 1, client->adapter->name);
>
> + if (client->irq) {
> + err = devm_request_threaded_irq(&client->dev,
> + client->irq,
> + NULL, adv76xx_irq_handler,
> + IRQF_TRIGGER_LOW|IRQF_ONESHOT,
While you hardcode the type to active low in int1_config, a board could have
an inverter on the irq line, making it active high when it reaches the
interrupt controller.
Unless I'm mistaken this will be handled properly if you set the correct
interrupt level in DT, so you can just remove the IRQF_TRIGGER_LOW flag here.
Apart from that,
Reviewed-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
> + dev_name(&client->dev), state);
> + if (err)
> + goto err_entity;
> + }
> +
> err = v4l2_async_register_subdev(sd);
> if (err)
> goto err_entity;
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
