> -----Original Message-----
> From: Nath, Arindam [mailto:[email protected]]
> Sent: Wednesday, March 23, 2011 12:06 PM
> To: Subhash Jadavani; [email protected]
> Cc: [email protected]; [email protected]; linux-
> [email protected]; Su, Henry; Lu, Aaron; [email protected]
> Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs bus speed
> mode selection
>
>
>
> > -----Original Message-----
> > From: Subhash Jadavani [mailto:[email protected]]
> > Sent: Wednesday, March 23, 2011 11:56 AM
> > To: Nath, Arindam; [email protected]
> > Cc: [email protected]; [email protected]; linux-
> > [email protected]; Su, Henry; Lu, Aaron; [email protected]
> > Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs bus speed
> > mode selection
> >
> >
> >
> > > -----Original Message-----
> > > From: [email protected] [mailto:linux-mmc-
> > > [email protected]] On Behalf Of Nath, Arindam
> > > Sent: Wednesday, March 23, 2011 11:48 AM
> > > To: Subhash Jadavani; [email protected]
> > > Cc: [email protected]; [email protected]; linux-
> > > [email protected]; Su, Henry; Lu, Aaron; [email protected]
> > > Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs bus
> speed
> > > mode selection
> > >
> > > Hi Subhash,
> > >
> > >
> > > > -----Original Message-----
> > > > From: Subhash Jadavani [mailto:[email protected]]
> > > > Sent: Wednesday, March 23, 2011 11:44 AM
> > > > To: Nath, Arindam; [email protected]
> > > > Cc: [email protected]; [email protected]; linux-
> > > > [email protected]; Su, Henry; Lu, Aaron; [email protected]
> > > > Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs bus
> > speed
> > > > mode selection
> > > >
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: [email protected] [mailto:linux-mmc-
> > > > > [email protected]] On Behalf Of Nath, Arindam
> > > > > Sent: Wednesday, March 23, 2011 11:35 AM
> > > > > To: Subhash Jadavani; [email protected]
> > > > > Cc: [email protected]; [email protected]; linux-
> > > > > [email protected]; Su, Henry; Lu, Aaron; [email protected]
> > > > > Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs bus
> > > speed
> > > > > mode selection
> > > > >
> > > > > Hi Subhash,
> > > > >
> > > > >
> > > > > > -----Original Message-----
> > > > > > From: Subhash Jadavani [mailto:[email protected]]
> > > > > > Sent: Monday, March 21, 2011 12:13 PM
> > > > > > To: Nath, Arindam; [email protected]
> > > > > > Cc: [email protected]; [email protected]; linux-
> > > > > > [email protected]; Su, Henry; Lu, Aaron;
> [email protected]
> > > > > > Subject: RE: [PATCH v2 06/12] mmc: sd: add support for uhs
> bus
> > > > speed
> > > > > > mode selection
> > > > > >
> > > > > >
> > > > > >
> > > > > > > -----Original Message-----
> > > > > > > From: Arindam Nath [mailto:[email protected]] On Behalf
> Of
> > > > > Arindam
> > > > > > > Nath
> > > > > > > Sent: Friday, March 04, 2011 5:03 PM
> > > > > > > To: [email protected]
> > > > > > > Cc: [email protected]; [email protected];
> > > > > > > [email protected]; [email protected];
> > > > > [email protected];
> > > > > > > [email protected]; [email protected]; Arindam Nath
> > > > > > > Subject: [PATCH v2 06/12] mmc: sd: add support for uhs bus
> > > speed
> > > > > mode
> > > > > > > selection
> > > > > > >
> > > > > > > This patch adds support for setting UHS-I bus speed mode
> > during
> > > > > UHS-I
> > > > > > > initialization procedure. Since both the host and card can
> > > > support
> > > > > > > more than one bus speed, we select the highest speed based
> on
> > > > both
> > > > > of
> > > > > > > their capabilities. First we set the bus speed mode for the
> > > card
> > > > > > using
> > > > > > > CMD6 mode 1, and then we program the host controller to
> > support
> > > > the
> > > > > > > required speed mode. We also set High Speed Enable in case
> > one
> > > of
> > > > > the
> > > > > > > UHS-I modes is selected. Since MMC_TIMING_UHS_SDR25 is same
> > as
> > > > > > > MMC_TIMING_SD_HS, we don't need to set the SDHCI_CTRL_HISPD
> > > flag
> > > > > for
> > > > > > > UHS SDR25 again. We also take care to reset SD clock before
> > > > setting
> > > > > > > UHS mode in the Host Control2 register, and then re-enable
> it
> > > as
> > > > > per
> > > > > > > the Host Controller spec v3.00. We set the clock frequency
> > for
> > > > the
> > > > > > > UHS-I mode selected.
> > > > > > >
> > > > > > > Signed-off-by: Arindam Nath <[email protected]>
> > > > > > > ---
> > > > > > > drivers/mmc/core/sd.c | 91
> > > > > > > ++++++++++++++++++++++++++++++++++++++++++++++
> > > > > > > drivers/mmc/host/sdhci.c | 32 +++++++++++++++-
> > > > > > > drivers/mmc/host/sdhci.h | 5 +++
> > > > > > > include/linux/mmc/card.h | 16 ++++++++
> > > > > > > include/linux/mmc/host.h | 4 ++
> > > > > > > 5 files changed, 146 insertions(+), 2 deletions(-)
> > > > > > >
> > > > > > > diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> > > > > > > index f6a4fab..ec0d8e6 100644
> > > > > > > --- a/drivers/mmc/core/sd.c
> > > > > > > +++ b/drivers/mmc/core/sd.c
> > > > > > > @@ -464,6 +464,92 @@ static int
> sd_select_driver_type(struct
> > > > > mmc_card
> > > > > > > *card, u8 *status)
> > > > > > > return 0;
> > > > > > > }
> > > > > > >
> > > > > > > +static int sd_set_bus_speed_mode(struct mmc_card *card, u8
> > > > > *status)
> > > > > > > +{
> > > > > > > + unsigned int bus_speed, timing;
> > > > > > > + int err;
> > > > > > > +
> > > > > > > + /*
> > > > > > > + * If the host doesn't support any of the UHS-I
> > modes,
> > > > fallback
> > > > > > > on
> > > > > > > + * default speed.
> > > > > > > + */
> > > > > > > + if (!(card->host->caps & (MMC_CAP_UHS_SDR12 |
> > > > MMC_CAP_UHS_SDR25 |
> > > > > > > + MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
> > > > MMC_CAP_UHS_DDR50)))
> > > > > > > + return 0;
> > > > > > > +
> > > > > > > + if (card->host->caps & MMC_CAP_UHS_SDR104) {
> > > > > > > + if (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR104)
> > > > {
> > > > > > > + bus_speed = UHS_SDR104_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR104;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR104_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_SDR50)
> > > > > > > {
> > > > > > > + bus_speed = UHS_SDR50_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR50;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR50_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_DDR50)
> > > > > > > {
> > > > > > > + bus_speed = UHS_DDR50_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_DDR50;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_DDR50_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_SDR25)
> > > > > > > {
> > > > > > > + bus_speed = UHS_SDR25_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR25;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR25_MAX_DTR;
> > > > > > > + }
> > > > > >
> > > > > > I would not agree that if Host cap is set to
> MMC_CAP_UHS_SDR104
> > > > > implies
> > > > > > that
> > > > > > DDR50 mode is supported by host. There may be a case where
> host
> > > > > > controller
> > > > > > only support SDR timing modes.
> > > > > > Basically if host should advertise all the supported modes
> > > (SDR104,
> > > > > > SDR50,
> > > > > > SDR25, SDR12 & DDR) by caps and then we should choose the
> > highest
> > > > > > performance mode depending on both the card and host's
> highest
> > > > > > performance
> > > > > > mode.
> > > > > >
> > > > > > So this should be the check:
> > > > > >
> > > > > > if ((card->host->caps & MMC_CAP_UHS_SDR104 &&
> > > > > > (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR104)) {
> > > > > > bus_speed = UHS_SDR104_BUS_SPEED;
> > > > > > timing = MMC_TIMING_UHS_SDR104;
> > > > > > card->sw_caps.uhs_max_dtr =
> > UHS_SDR104_MAX_DTR;
> > > > > > } else if ((card->host->caps & MMC_CAP_UHS_DDR50 &&
> > > > > > (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_DDR50)) {
> > > > > > bus_speed = UHS_DDR50_BUS_SPEED;
> > > > > > timing = MMC_TIMING_UHS_DDR50;
> > > > > > card->sw_caps.uhs_max_dtr =
> > UHS_DDR50_MAX_DTR;
> > > > > > } else if ((card->host->caps & MMC_CAP_UHS_SDR50 &&
> > > > > > (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR50)) {
> > > > > > bus_speed = UHS_SDR50_BUS_SPEED;
> > > > > > timing = MMC_TIMING_UHS_SDR50;
> > > > > > card->sw_caps.uhs_max_dtr =
> > UHS_SDR50_MAX_DTR;
> > > > > > } else if ((card->host->caps & MMC_CAP_UHS_SDR25 &&
> > > > > > (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR25)) {
> > > > > > bus_speed = UHS_SDR50_BUS_SPEED;
> > > > > > timing = MMC_TIMING_UHS_SDR25;
> > > > > > card->sw_caps.uhs_max_dtr =
> > UHS_SDR25_MAX_DTR;
> > > > > > } else if ((card->host->caps & MMC_CAP_UHS_SDR12 &&
> > > > > > (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR12)) {
> > > > > > bus_speed = UHS_SDR12_BUS_SPEED;
> > > > > > timing = MMC_TIMING_UHS_SDR12;
> > > > > > card->sw_caps.uhs_max_dtr =
> > UHS_SDR12_MAX_DTR;
> > > > > > }
> > > > >
> > > > > A host capable of operating at a higher bus speed mode should
> be
> > > able
> > > > > to support cards with a lower bus speed mode. In case of your
> > > > > conditions checks above, you are checking for the exact match
> for
> > > the
> > > > > bus speed modes, otherwise you will fall back on using default
> > bus
> > > > > speed mode, thus performance loss.
> > > >
> > > > Why should we implicitly assume that host supporting SDR104 mode
> > > would
> > > > also
> > > > support DDR50 mode? Is there any spec. which says so? If not then
> > we
> > > > should
> > > > rely on host capability to take the decision. DDR50 would require
> > > > different
> > > > timing implementation on the host side and host may choose not to
> > > > implement
> > > > DDR50 timing support then?
> > > >
> > > > I would agree that host supporting SDR104 mode should also be
> > > > supporting
> > > > SDR50/SDR25/SDR12 modes but it may not be true for DDR50 mode.
> > >
> > > Please refer to footnote of table 3-5 of the Physical Layer spec
> > v3.01.
> > > It says:
> > >
> > > "The card supports a UHS-I mode shall support all lower UHS-I
> modes."
> > >
> > > So if this is true for card, doesn't the same apply to host?
> >
> > Yes, this is the exact point I am stretching. Spec. never says the
> same
> > thing for host so we should not assume it. we already have luxury to
> > use
> > host caps then why should we assume something which may not be
> correct?
>
> I still think we should have a combination which works best based on
> the capabilities of the host and card, rather than falling back to
> default bus speed right away. I can try to separate out the case for
> DDR50, if you want that. Otherwise, I will wait for few more comments
> on the same.
Thanks. My code snippet was just an example. Yes, just separating out DDR50
should be enough.
>
> Thanks,
> Arindam
>
> >
> > >
> > > Thanks,
> > > Arindam
> > >
> > > >
> > > > >
> > > > > Thanks,
> > > > > Arindam
> > > > >
> > > > > >
> > > > > > Regards,
> > > > > > Subhash
> > > > > >
> > > > > >
> > > > > > > + } else if (card->host->caps & MMC_CAP_UHS_SDR50) {
> > > > > > > + if ((card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR104)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR50))
> > > > {
> > > > > > > + bus_speed = UHS_SDR50_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR50;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR50_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_DDR50)
> > > > > > > {
> > > > > > > + bus_speed = UHS_DDR50_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_DDR50;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_DDR50_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_SDR25)
> > > > > > > {
> > > > > > > + bus_speed = UHS_SDR25_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR25;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR25_MAX_DTR;
> > > > > > > + }
> > > > > > > + } else if (card->host->caps & MMC_CAP_UHS_DDR50) {
> > > > > > > + if ((card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR104)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR50)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_DDR50))
> > > > {
> > > > > > > + bus_speed = UHS_DDR50_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_DDR50;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_DDR50_MAX_DTR;
> > > > > > > + } else if (card->sw_caps.uhs_bus_mode &
> > > > SD_MODE_UHS_SDR25)
> > > > > > > {
> > > > > > > + bus_speed = UHS_SDR25_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR25;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR25_MAX_DTR;
> > > > > > > + }
> > > > > > > + } else if (card->host->caps & MMC_CAP_UHS_SDR25) {
> > > > > > > + if ((card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR104)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR50)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_DDR50)
> > > > ||
> > > > > > > + (card->sw_caps.uhs_bus_mode &
> > > SD_MODE_UHS_SDR25))
> > > > {
> > > > > > > + bus_speed = UHS_SDR25_BUS_SPEED;
> > > > > > > + timing = MMC_TIMING_UHS_SDR25;
> > > > > > > + card->sw_caps.uhs_max_dtr =
> > > UHS_SDR25_MAX_DTR;
> > > > > > > + }
> > > > > > > + }
> > > > > > > +
> > > > > > > + err = mmc_sd_switch(card, 1, 0, bus_speed, status);
> > > > > > > + if (err)
> > > > > > > + return err;
> > > > > > > +
> > > > > > > + if ((status[16] & 0xF) != bus_speed)
> > > > > > > + printk(KERN_WARNING "%s: Problem setting
> bus
> > > speed
> > > > > > > mode!\n",
> > > > > > > + mmc_hostname(card->host));
> > > > > > > + else {
> > > > > > > + if (bus_speed) {
> > > > > > > + mmc_set_timing(card->host, timing);
> > > > > > > + mmc_set_clock(card->host,
> > > > > > card->sw_caps.uhs_max_dtr);
> > > > > > > + }
> > > > > > > + }
> > > > > > > +
> > > > > > > + return 0;
> > > > > > > +}
> > > > > > > +
> > > > > > > /*
> > > > > > > * UHS-I specific initialization procedure
> > > > > > > */
> > > > > > > @@ -499,6 +585,11 @@ static int mmc_sd_init_uhs_card(struct
> > > > > mmc_card
> > > > > > > *card)
> > > > > > >
> > > > > > > /* Set the driver strength for the card */
> > > > > > > err = sd_select_driver_type(card, status);
> > > > > > > + if (err)
> > > > > > > + goto out;
> > > > > > > +
> > > > > > > + /* Set bus speed mode of the card */
> > > > > > > + err = sd_set_bus_speed_mode(card, status);
> > > > > > >
> > > > > > > out:
> > > > > > > kfree(status);
> > > > > > > diff --git a/drivers/mmc/host/sdhci.c
> > > b/drivers/mmc/host/sdhci.c
> > > > > > > index 5d3bb11..f127fa2 100644
> > > > > > > --- a/drivers/mmc/host/sdhci.c
> > > > > > > +++ b/drivers/mmc/host/sdhci.c
> > > > > > > @@ -1278,7 +1278,13 @@ static void sdhci_set_ios(struct
> > > mmc_host
> > > > > > *mmc,
> > > > > > > struct mmc_ios *ios)
> > > > > > > ctrl &= ~SDHCI_CTRL_HISPD;
> > > > > > >
> > > > > > > if (host->version >= SDHCI_SPEC_300) {
> > > > > > > - u16 ctrl_2;
> > > > > > > + u16 clk, ctrl_2;
> > > > > > > +
> > > > > > > + /* In case of UHS-I modes, set High Speed
> > > Enable */
> > > > > > > + if ((ios->timing == MMC_TIMING_UHS_SDR50)
> ||
> > > > > > > + (ios->timing == MMC_TIMING_UHS_SDR104)
> ||
> > > > > > > + (ios->timing == MMC_TIMING_UHS_DDR50))
> > > > > > > + ctrl |= SDHCI_CTRL_HISPD;
> > > > > > >
> > > > > > > ctrl_2 = sdhci_readw(host,
> > > SDHCI_HOST_CONTROL2);
> > > > > > > if (!(ctrl_2 &
> SDHCI_CTRL_PRESET_VAL_ENABLE))
> > {
> > > > > > > @@ -1300,7 +1306,6 @@ static void sdhci_set_ios(struct
> > mmc_host
> > > > > *mmc,
> > > > > > > struct mmc_ios *ios)
> > > > > > > * need to reset SD Clock Enable
> > before
> > > > changing
> > > > > > High
> > > > > > > * Speed Enable to avoid generating
> > > clock
> > > > gliches.
> > > > > > > */
> > > > > > > - u16 clk;
> > > > > > >
> > > > > > > /* Reset SD Clock Enable */
> > > > > > > clk = sdhci_readw(host,
> > > SDHCI_CLOCK_CONTROL);
> > > > > > > @@ -1313,6 +1318,29 @@ static void sdhci_set_ios(struct
> > > mmc_host
> > > > > > *mmc,
> > > > > > > struct mmc_ios *ios)
> > > > > > > clk |= SDHCI_CLOCK_CARD_EN;
> > > > > > > sdhci_writew(host, clk,
> > > SDHCI_CLOCK_CONTROL);
> > > > > > > }
> > > > > > > +
> > > > > > > + ctrl_2 = sdhci_readw(host,
> > > SDHCI_HOST_CONTROL2);
> > > > > > > +
> > > > > > > + /* Select Bus Speed Mode for host */
> > > > > > > + if (ios->timing == MMC_TIMING_UHS_SDR25)
> > > > > > > + ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
> > > > > > > + else if (ios->timing ==
> MMC_TIMING_UHS_SDR50)
> > > > > > > + ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
> > > > > > > + else if (ios->timing ==
> > MMC_TIMING_UHS_SDR104)
> > > > > > > + ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
> > > > > > > + else if (ios->timing ==
> MMC_TIMING_UHS_DDR50)
> > > > > > > + ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
> > > > > > > +
> > > > > > > + /* Reset SD Clock Enable */
> > > > > > > + clk = sdhci_readw(host,
> SDHCI_CLOCK_CONTROL);
> > > > > > > + clk &= ~SDHCI_CLOCK_CARD_EN;
> > > > > > > + sdhci_writew(host, clk,
> SDHCI_CLOCK_CONTROL);
> > > > > > > +
> > > > > > > + sdhci_writew(host, ctrl_2,
> > > SDHCI_HOST_CONTROL2);
> > > > > > > +
> > > > > > > + /* Re-enable SD Clock */
> > > > > > > + clk |= SDHCI_CLOCK_CARD_EN;
> > > > > > > + sdhci_writew(host, clk,
> SDHCI_CLOCK_CONTROL);
> > > > > > > } else
> > > > > > > sdhci_writeb(host, ctrl,
> > SDHCI_HOST_CONTROL1);
> > > > > > >
> > > > > > > diff --git a/drivers/mmc/host/sdhci.h
> > > b/drivers/mmc/host/sdhci.h
> > > > > > > index a407b5b..5bf244d 100644
> > > > > > > --- a/drivers/mmc/host/sdhci.h
> > > > > > > +++ b/drivers/mmc/host/sdhci.h
> > > > > > > @@ -150,6 +150,11 @@
> > > > > > > #define SDHCI_ACMD12_ERR 0x3C
> > > > > > >
> > > > > > > #define SDHCI_HOST_CONTROL2 0x3E
> > > > > > > +#define SDHCI_CTRL_UHS_SDR12 0x0000
> > > > > > > +#define SDHCI_CTRL_UHS_SDR25 0x0001
> > > > > > > +#define SDHCI_CTRL_UHS_SDR50 0x0002
> > > > > > > +#define SDHCI_CTRL_UHS_SDR104 0x0003
> > > > > > > +#define SDHCI_CTRL_UHS_DDR50 0x0004
> > > > > > > #define SDHCI_CTRL_VDD_180 0x0008
> > > > > > > #define SDHCI_CTRL_DRV_TYPE_B 0x0000
> > > > > > > #define SDHCI_CTRL_DRV_TYPE_A 0x0010
> > > > > > > diff --git a/include/linux/mmc/card.h
> > > b/include/linux/mmc/card.h
> > > > > > > index 2d7f7a3..0b24c41 100644
> > > > > > > --- a/include/linux/mmc/card.h
> > > > > > > +++ b/include/linux/mmc/card.h
> > > > > > > @@ -75,7 +75,23 @@ struct sd_ssr {
> > > > > > >
> > > > > > > struct sd_switch_caps {
> > > > > > > unsigned int hs_max_dtr;
> > > > > > > + unsigned int uhs_max_dtr;
> > > > > > > +#define UHS_SDR104_MAX_DTR 208000000
> > > > > > > +#define UHS_SDR50_MAX_DTR 100000000
> > > > > > > +#define UHS_DDR50_MAX_DTR 50000000
> > > > > > > +#define UHS_SDR25_MAX_DTR 50000000
> > > > > > > unsigned int uhs_bus_mode;
> > > > > > > +#define UHS_SDR12_BUS_SPEED 0
> > > > > > > +#define UHS_SDR25_BUS_SPEED 1
> > > > > > > +#define UHS_SDR50_BUS_SPEED 2
> > > > > > > +#define UHS_SDR104_BUS_SPEED 3
> > > > > > > +#define UHS_DDR50_BUS_SPEED 4
> > > > > > > +
> > > > > > > +#define SD_MODE_UHS_SDR12 (1 << UHS_SDR12_BUS_SPEED)
> > > > > > > +#define SD_MODE_UHS_SDR25 (1 << UHS_SDR25_BUS_SPEED)
> > > > > > > +#define SD_MODE_UHS_SDR50 (1 << UHS_SDR50_BUS_SPEED)
> > > > > > > +#define SD_MODE_UHS_SDR104 (1 << UHS_SDR104_BUS_SPEED)
> > > > > > > +#define SD_MODE_UHS_DDR50 (1 << UHS_DDR50_BUS_SPEED)
> > > > > > > unsigned int uhs_drv_type;
> > > > > > > #define SD_DRIVER_TYPE_B 0x01
> > > > > > > #define SD_DRIVER_TYPE_A 0x02
> > > > > > > diff --git a/include/linux/mmc/host.h
> > > b/include/linux/mmc/host.h
> > > > > > > index bc2121e..4dfff6d 100644
> > > > > > > --- a/include/linux/mmc/host.h
> > > > > > > +++ b/include/linux/mmc/host.h
> > > > > > > @@ -50,6 +50,10 @@ struct mmc_ios {
> > > > > > > #define MMC_TIMING_LEGACY 0
> > > > > > > #define MMC_TIMING_MMC_HS 1
> > > > > > > #define MMC_TIMING_SD_HS 2
> > > > > > > +#define MMC_TIMING_UHS_SDR25 MMC_TIMING_SD_HS
> > > > > > > +#define MMC_TIMING_UHS_SDR50 3
> > > > > > > +#define MMC_TIMING_UHS_SDR104 4
> > > > > > > +#define MMC_TIMING_UHS_DDR50 5
> > > > > > >
> > > > > > > unsigned char ddr; /* dual
> data
> > > rate used
> > > > */
> > > > > > >
> > > > > > > --
> > > > > > > 1.7.1
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > > --
> > > > > To unsubscribe from this list: send the line "unsubscribe
> linux-
> > > mmc"
> > > > in
> > > > > the body of a message to [email protected]
> > > > > More majordomo info at http://vger.kernel.org/majordomo-
> > info.html
> > > >
> > >
> > >
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe linux-
> mmc"
> > in
> > > the body of a message to [email protected]
> > > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
