Hi!
> Eanble the ADMA2 mode on freescale esdhc imx driver,
> tested on MX51 and MX53.
>
> Only ADMA2 mode is enabled, MX25/35 can't support the ADMA2 mode.
> So this patch is only used for MX51/53.
> The ADMA2 mode supported or not can be distinguished by the
> Capability Register(offset 0x40) of eSDHC module.
> Up to now, only MX51/MX53 set the ADMA2 supported bit(Bit20) in the
> Capability Register.
I tried it on mx25 (3-stack), and it unfortunately breaks things:
...
mmc0: unrecognised SCR structure version 12
mmc0: error -22 whilst initialising SD card
...
It may be interfering with my changs, but...
> +/*
> + * There is INT DMA ERR mis-match between eSDHC and STD SDHC SPEC
> + * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
> + * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
> + * Define this macro DMA error INT for fsl eSDHC
> + */
> +#define SDHCI_INT_VENDOR_SPEC_DMA_ERR 0x10000000
> +
> #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0)
> /*
> * The CMDTYPE of the CMD register (offset 0xE) should be set to
> @@ -80,6 +88,20 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
> val |= SDHCI_CARD_PRESENT;
> }
>
> + if (unlikely(reg == SDHCI_CAPABILITIES)) {
> + if (val & SDHCI_CAN_DO_ADMA1) {
> + val &= ~SDHCI_CAN_DO_ADMA1;
> + val |= SDHCI_CAN_DO_ADMA2;
> + }
> + }
> +
> + if (unlikely(reg == SDHCI_INT_STATUS)) {
> + if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
> + val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
> + val |= SDHCI_INT_ADMA_ERROR;
> + }
> + }
> +
> return val;
> }
>
Unfortunately register differences are common. Is there better
approach than patching it in low level functions like this?
> @@ -322,9 +351,10 @@ static void esdhc_pltfm_exit(struct sdhci_host *host)
> }
>
> struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
> - .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_ADMA
> + .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
> + | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
> + | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
> | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
If I re-add "SDHCI_QUIRK_BROKEN_ADMA", it starts working.
Pavel
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
