Hi Jaehoon,
On Tue, Nov 8, 2011 at 1:43 PM, Jae hoon Chung <[email protected]> wrote:
> Hi Per.
>
> 2011/11/5 Per Forlin <[email protected]>:
>> Hi Jaehoon,
>>
>> On Wed, Nov 2, 2011 at 11:28 AM, Jaehoon Chung <[email protected]>
>> wrote:
>>> Enable eMMC background operations (BKOPS) feature.
>>>
>>> If URGENT_BKOPS is set after a response, note that BKOPS
>>> are required. After all I/O requests are finished, run
>>> BKOPS if required. Should read/write operations be requested
>>> during BKOPS, first issue HPI to interrupt the ongoing BKOPS
>>> and then service the request.
>>>
>>> If you want to enable this feature, set MMC_CAP2_BKOPS.
>>>
>>> Signed-off-by: Jaehoon Chung <[email protected]>
>>> Signed-off-by: Kyungmin Park <[email protected]>
>>> CC: Hanumath Prasad <[email protected]>
>>>
>>> ---
>>> Changelog V2:
>>> - Use EXCEPTION_STATUS instead of URGENT_BKOPS
>>> - Add function to check Exception_status(for eMMC4.5)
>>> - remove unnecessary code.
>>>
>>> drivers/mmc/card/block.c | 9 +++++
>>> drivers/mmc/card/queue.c | 4 ++
>>> drivers/mmc/core/core.c | 87
>>> ++++++++++++++++++++++++++++++++++++++++++++
>>> drivers/mmc/core/mmc.c | 9 ++++-
>>> drivers/mmc/core/mmc_ops.c | 4 ++
>>> include/linux/mmc/card.h | 12 ++++++
>>> include/linux/mmc/core.h | 3 ++
>>> include/linux/mmc/host.h | 1 +
>>> include/linux/mmc/mmc.h | 14 +++++++
>>> 9 files changed, 142 insertions(+), 1 deletions(-)
>>>
>>> diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
>>> index a1cb21f..fbfb405 100644
>>> --- a/drivers/mmc/card/block.c
>>> +++ b/drivers/mmc/card/block.c
>>> @@ -1192,6 +1192,15 @@ static int mmc_blk_issue_rw_rq(struct mmc_queue *mq,
>>> struct request *rqc)
>>> case MMC_BLK_SUCCESS:
>>> case MMC_BLK_PARTIAL:
>>> /*
>>> + * Check BKOPS urgency from each R1 response
>>> + */
>>> + if (mmc_card_mmc(card) &&
>>> + (brq->cmd.resp[0] & R1_EXCEPTION_EVENT)) {
>>> + if (mmc_is_exception_event(card,
>>> + EXT_CSD_URGENT_BKOPS))
>>> + mmc_card_set_need_bkops(card);
>>> + }
>>> + /*
>>> * A block was successfully transferred.
>>> */
>>> mmc_blk_reset_success(md, type);
>>> diff --git a/drivers/mmc/card/queue.c b/drivers/mmc/card/queue.c
>>> index dcad59c..20bb4a5 100644
>>> --- a/drivers/mmc/card/queue.c
>>> +++ b/drivers/mmc/card/queue.c
>>> @@ -61,6 +61,9 @@ static int mmc_queue_thread(void *d)
>>> spin_unlock_irq(q->queue_lock);
>>>
>>> if (req || mq->mqrq_prev->req) {
>>> + if (mmc_card_doing_bkops(mq->card))
>>> + mmc_interrupt_bkops(mq->card);
>>> +
>>> set_current_state(TASK_RUNNING);
>>> mq->issue_fn(mq, req);
>>> } else {
>>> @@ -68,6 +71,7 @@ static int mmc_queue_thread(void *d)
>>> set_current_state(TASK_RUNNING);
>>> break;
>>> }
>>> + mmc_start_bkops(mq->card);
>>> up(&mq->thread_sem);
>>> schedule();
>>> down(&mq->thread_sem);
>>> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
>>> index 5278ffb..41ea923 100644
>>> --- a/drivers/mmc/core/core.c
>>> +++ b/drivers/mmc/core/core.c
>>> @@ -238,6 +238,50 @@ mmc_start_request(struct mmc_host *host, struct
>>> mmc_request *mrq)
>>> host->ops->request(host, mrq);
>>> }
>>>
>>> +/**
>>> + * mmc_start_bkops - start BKOPS for supported cards
>>> + * @card: MMC card to start BKOPS
>>> + *
>>> + * Start background operations whenever requested.
>>> + * when the urgent BKOPS bit is set in a R1 command response
>>> + * then background operations should be started immediately.
>>> +*/
>>> +void mmc_start_bkops(struct mmc_card *card)
>>> +{
>>> + int err;
>>> + unsigned long flags;
>>> +
>>
>>> + card->host->caps2 |= MMC_CAP2_BKOPS;
>> I guess this should be set by the host driver?
> You're right...it's my mistake...i will remove this..
>>
>>> + if ((!card || !card->ext_csd.bkops_en) &&
>>> + !(card->host->caps2 & MMC_CAP2_BKOPS))
>> I don't really understand this. If card is NULL it will seg-fault.
>>
>> Do you mean:
>> if (!card)
>> return
>>
>> if (!card->ext_csd.bkops_en ||
>> !(card->host->caps2 & MMC_CAP2_BKOPS))
>> return
>>
>> Do you really need to check card != NULL? Consider BUG_ON
> Maybe if (!card && !card->ext_csd.bkops_en) is correctly...i think...
If card is NULL it will seg-fault.
Did you mean: if (card && !card->ext_csd.bkops_en)
I would suggest.
# return if card is NULL
if (!card)
return
# if card is set, check the values.
if (!card->ext_csd.bkops_en ||
!(card->host->caps2 & MMC_CAP2_BKOPS))
return
>>
>>> + return;
>>> +
>>> + /*
>>> + * If card is already doing bkops or need for
>>> + * bkops flag is not set, then do nothing just
>>> + * return
>>> + */
>>> + if (mmc_card_doing_bkops(card)
>>> + || !mmc_card_need_bkops(card))
>>> + return;
>>> +
>>> + mmc_claim_host(card->host);
>>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>>> + EXT_CSD_BKOPS_START, 1, 0);
>>> + if (err) {
>>> + pr_warning("error %d starting bkops\n", err);
>>> + mmc_card_clr_need_bkops(card);
>>> + goto out;
>>> + }
>>> + spin_lock_irqsave(&card->host->lock, flags);
>>> + mmc_card_clr_need_bkops(card);
>>> + mmc_card_set_doing_bkops(card);
>>> + spin_unlock_irqrestore(&card->host->lock, flags);
>>> +out:
>>> + mmc_release_host(card->host);
>>> +}
>>> +EXPORT_SYMBOL(mmc_start_bkops);
>>> +
>>> static void mmc_wait_done(struct mmc_request *mrq)
>>> {
>>> complete(&mrq->completion);
>>> @@ -466,6 +510,49 @@ int mmc_wait_for_cmd(struct mmc_host *host, struct
>>> mmc_command *cmd, int retries
>>> EXPORT_SYMBOL(mmc_wait_for_cmd);
>>>
>>> /**
>>> + * mmc_interrupt_bkops - interrupt ongoing BKOPS
>>> + * @card: MMC card to check BKOPS
>>> + *
>>> + * Send HPI command to interrupt ongoing background operations,
>>> + * to allow rapid servicing of foreground operations,e.g. read/
>>> + * writes. Wait until the card comes out of the programming state
>>> + * to avoid errors in servicing read/write requests.
>>> + */
>>> +int mmc_interrupt_bkops(struct mmc_card *card)
>>> +{
>>> + int err = 0;
>>> + unsigned long flags;
>>> +
>>> + BUG_ON(!card);
>>> +
>>> + err = mmc_interrupt_hpi(card);
>>> +
>>> + spin_lock_irqsave(&card->host->lock, flags);
>>> + mmc_card_clr_doing_bkops(card);
>>> + spin_unlock_irqrestore(&card->host->lock, flags);
>>> +
>>> + return err;
>>> +}
>>> +EXPORT_SYMBOL(mmc_interrupt_bkops);
>>> +
>>> +int mmc_is_exception_event(struct mmc_card *card, unsigned int value)
>>> +{
>>> + int err;
>>> + u8 ext_csd[512];
>>> +
>>> + /* In eMMC 4.41, R1_EXCEPTION_EVENT is URGENT_BKOPS */
>>> + if (card->ext_csd.rev == 5)
>>> + return 1;
>>> +
>>> + err = mmc_send_ext_csd(card, ext_csd);
>>> + if (err)
>>> + return err;
>>> +
>>> + return (ext_csd[EXT_CSD_EXCEPTION_STATUS] & value) ? 1 : 0;
>>> +}
>>> +EXPORT_SYMBOL(mmc_is_exception_event);
>>> +
>>> +/**
>>> * mmc_set_data_timeout - set the timeout for a data command
>>> * @data: data phase for command
>>> * @card: the MMC card associated with the data transfer
>>> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
>>> index 3627044..af40fbb 100644
>>> --- a/drivers/mmc/core/mmc.c
>>> +++ b/drivers/mmc/core/mmc.c
>>> @@ -448,6 +448,14 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8
>>> *ext_csd)
>>> }
>>>
>>> if (card->ext_csd.rev >= 5) {
>>> + /* check whether the eMMC card support BKOPS */
>>> + if (ext_csd[EXT_CSD_BKOPS_SUPPORT] & 0x1) {
>>> + card->ext_csd.bkops = 1;
>>> + card->ext_csd.bkops_en = 1;
>> What if the card has not enabled bkops? This bit could be unset.
>> card->ext_csd.bkops_en = ext_csd[EXT_CSD_BKOPS_EN];
> When card is supported the bkops, bkops_en bit is set by default...
>
How do you know if the bkops_en is really enabled in th ext_csd?
It could be unset in the ext_csd, right?
>>
>>> + card->ext_csd.raw_bkops_status =
>>> + ext_csd[EXT_CSD_BKOPS_STATUS];
>>> + }
>>> +
>>> /* check whether the eMMC card supports HPI */
>>> if (ext_csd[EXT_CSD_HPI_FEATURES] & 0x1) {
>>> card->ext_csd.hpi = 1;
>>> @@ -498,7 +506,6 @@ static inline void mmc_free_ext_csd(u8 *ext_csd)
>>> kfree(ext_csd);
>>> }
>>>
>>> -
>>> static int mmc_compare_ext_csds(struct mmc_card *card, unsigned bus_width)
>>> {
>>> u8 *bw_ext_csd;
>>> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
>>> index 007863e..7653e33 100644
>>> --- a/drivers/mmc/core/mmc_ops.c
>>> +++ b/drivers/mmc/core/mmc_ops.c
>>> @@ -398,6 +398,10 @@ int mmc_switch(struct mmc_card *card, u8 set, u8
>>> index, u8 value,
>>> if (err)
>>> return err;
>>>
>>> + /* No need to check card status in case of BKOPS switch*/
>>> + if (index == EXT_CSD_BKOPS_START)
>>> + return 0;
>>> +
>>> /* Must check status to be sure of no errors */
>>> do {
>>> err = mmc_send_status(card, &status);
>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
>>> index 415f2db..34740c5 100644
>>> --- a/include/linux/mmc/card.h
>>> +++ b/include/linux/mmc/card.h
>>> @@ -71,6 +71,8 @@ struct mmc_ext_csd {
>>> bool hpi_en; /* HPI enablebit */
>>> bool hpi; /* HPI support bit */
>>> unsigned int hpi_cmd; /* cmd used as HPI */
>>> + bool bkops; /* background support bit */
>>> + bool bkops_en; /* background enable bit */
>>> u8 raw_partition_support; /* 160 */
>>> u8 raw_erased_mem_count; /* 181 */
>>> u8 raw_ext_csd_structure; /* 194 */
>>> @@ -84,6 +86,7 @@ struct mmc_ext_csd {
>>> u8 raw_sec_erase_mult; /* 230 */
>>> u8 raw_sec_feature_support;/* 231 */
>>> u8 raw_trim_mult; /* 232 */
>>> + u8 raw_bkops_status; /* 246 */
>>> u8 raw_sectors[4]; /* 212 - 4 bytes */
>>>
>>> unsigned int feature_support;
>>> @@ -206,6 +209,8 @@ struct mmc_card {
>>> #define MMC_STATE_HIGHSPEED_DDR (1<<4) /* card is in high speed
>>> mode */
>>> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in ultra
>>> high speed mode */
>>> #define MMC_CARD_SDXC (1<<6) /* card is SDXC */
>>> +#define MMC_STATE_NEED_BKOPS (1<<7) /* card need to do BKOPS */
>>> +#define MMC_STATE_DOING_BKOPS (1<<8) /* card is doing BKOPS */
>>> unsigned int quirks; /* card quirks */
>>> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO FN0 writes
>>> outside of the VS CCCR range */
>>> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func->cur_blksize */
>>> @@ -365,6 +370,8 @@ static inline void __maybe_unused remove_quirk(struct
>>> mmc_card *card, int data)
>>> #define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR)
>>> #define mmc_sd_card_uhs(c) ((c)->state & MMC_STATE_ULTRAHIGHSPEED)
>>> #define mmc_card_ext_capacity(c) ((c)->state & MMC_CARD_SDXC)
>>> +#define mmc_card_need_bkops(c) ((c)->state & MMC_STATE_NEED_BKOPS)
>>> +#define mmc_card_doing_bkops(c) ((c)->state & MMC_STATE_DOING_BKOPS)
>>>
>>> #define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
>>> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
>>> @@ -373,6 +380,11 @@ static inline void __maybe_unused remove_quirk(struct
>>> mmc_card *card, int data)
>>> #define mmc_card_set_ddr_mode(c) ((c)->state |= MMC_STATE_HIGHSPEED_DDR)
>>> #define mmc_sd_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
>>> #define mmc_card_set_ext_capacity(c) ((c)->state |= MMC_CARD_SDXC)
>>> +#define mmc_card_set_need_bkops(c) ((c)->state |= MMC_STATE_NEED_BKOPS)
>>> +#define mmc_card_set_doing_bkops(c) ((c)->state |=
>>> MMC_STATE_DOING_BKOPS)
>>> +
>>> +#define mmc_card_clr_need_bkops(c) ((c)->state &=
>>> ~MMC_STATE_NEED_BKOPS)
>>> +#define mmc_card_clr_doing_bkops(c) ((c)->state &=
>>> ~MMC_STATE_DOING_BKOPS)
>>>
>>> /*
>>> * Quirk add/remove for MMC products.
>>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
>>> index 174a844..f6b997a 100644
>>> --- a/include/linux/mmc/core.h
>>> +++ b/include/linux/mmc/core.h
>>> @@ -134,6 +134,8 @@ struct mmc_host;
>>> struct mmc_card;
>>> struct mmc_async_req;
>>>
>>> +extern int mmc_interrupt_bkops(struct mmc_card *);
>>> +extern int mmc_is_exception_event(struct mmc_card *, unsigned int);
>>> extern struct mmc_async_req *mmc_start_req(struct mmc_host *,
>>> struct mmc_async_req *, int *);
>>> extern int mmc_interrupt_hpi(struct mmc_card *);
>>> @@ -163,6 +165,7 @@ extern int mmc_can_sanitize(struct mmc_card *card);
>>> extern int mmc_can_secure_erase_trim(struct mmc_card *card);
>>> extern int mmc_erase_group_aligned(struct mmc_card *card, unsigned int
>>> from,
>>> unsigned int nr);
>>> +extern void mmc_start_bkops(struct mmc_card *card);
>>> extern unsigned int mmc_calc_max_discard(struct mmc_card *card);
>>>
>>> extern int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen);
>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
>>> index a3ac9c4..692e5f6 100644
>>> --- a/include/linux/mmc/host.h
>>> +++ b/include/linux/mmc/host.h
>>> @@ -242,6 +242,7 @@ struct mmc_host {
>>> #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
>>> #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff
>>> supported */
>>> #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't
>>> work */
>>> +#define MMC_CAP2_BKOPS (1 << 4) /* BKOPS supported */
>>>
>>> mmc_pm_flag_t pm_caps; /* supported pm features */
>>> unsigned int power_notify_type;
>>> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
>>> index 0e71356..20b1420 100644
>>> --- a/include/linux/mmc/mmc.h
>>> +++ b/include/linux/mmc/mmc.h
>>> @@ -138,6 +138,7 @@ static inline bool mmc_op_multi(u32 opcode)
>>> #define R1_CURRENT_STATE(x) ((x & 0x00001E00) >> 9) /* sx, b (4 bits) */
>>> #define R1_READY_FOR_DATA (1 << 8) /* sx, a */
>>> #define R1_SWITCH_ERROR (1 << 7) /* sx, c */
>>> +#define R1_EXCEPTION_EVENT (1 << 6) /* sx, a */
>>> #define R1_APP_CMD (1 << 5) /* sr, c */
>>>
>>> #define R1_STATE_IDLE 0
>>> @@ -273,11 +274,14 @@ struct _mmc_csd {
>>> #define EXT_CSD_FLUSH_CACHE 32 /* W */
>>> #define EXT_CSD_CACHE_CTRL 33 /* R/W */
>>> #define EXT_CSD_POWER_OFF_NOTIFICATION 34 /* R/W */
>>> +#define EXT_CSD_EXCEPTION_STATUS 54 /* RO */
>>> #define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
>>> #define EXT_CSD_PARTITION_ATTRIBUTE 156 /* R/W */
>>> #define EXT_CSD_PARTITION_SUPPORT 160 /* RO */
>>> #define EXT_CSD_HPI_MGMT 161 /* R/W */
>>> #define EXT_CSD_RST_N_FUNCTION 162 /* R/W */
>>> +#define EXT_CSD_BKOPS_EN 163 /* R/W */
>>> +#define EXT_CSD_BKOPS_START 164 /* W */
>>> #define EXT_CSD_SANITIZE_START 165 /* W */
>>> #define EXT_CSD_WR_REL_PARAM 166 /* RO */
>>> #define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
>>> @@ -310,9 +314,11 @@ struct _mmc_csd {
>>> #define EXT_CSD_PWR_CL_200_360 237 /* RO */
>>> #define EXT_CSD_PWR_CL_DDR_52_195 238 /* RO */
>>> #define EXT_CSD_PWR_CL_DDR_52_360 239 /* RO */
>>> +#define EXT_CSD_BKOPS_STATUS 246 /* RO */
>>> #define EXT_CSD_POWER_OFF_LONG_TIME 247 /* RO */
>>> #define EXT_CSD_GENERIC_CMD6_TIME 248 /* RO */
>>> #define EXT_CSD_CACHE_SIZE 249 /* RO, 4 bytes */
>>> +#define EXT_CSD_BKOPS_SUPPORT 502 /* RO */
>>> #define EXT_CSD_HPI_FEATURES 503 /* RO */
>>>
>>> /*
>>> @@ -373,4 +379,12 @@ struct _mmc_csd {
>>> #define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits which are 1
>>> in value */
>>> #define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target to value */
>>>
>>> +/*
>>> + * EXCEPTION_EVENT_STATUS field (eMMC4.5)
>>> + */
>>> +#define EXT_CSD_URGENT_BKOPS BIT(0)
>>> +#define EXT_CSD_DYNCAP_NEEDED BIT(1)
>>> +#define EXT_CSD_SYSPOOL_EXHAUSTED BIT(2)
>>> +#define EXT_CSD_PACKED_FAILURE BIT(3)
>>> +
>>> #endif /* LINUX_MMC_MMC_H */
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>>> the body of a message to [email protected]
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
>>
>> Regards,
>> Per
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> the body of a message to [email protected]
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
