On 3 January 2013 14:19, Johan Rudholm <[email protected]> wrote:
> When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
> clock should be gated for 5 ms during the step. After enabling the
> clock, the host should wait for at least 1 ms before checking for
> failure. Failure by the card to switch is indicated by dat[0:3] being
> pulled low. The host should check for this condition and power-cycle
> the card if failure is indicated.
>
> Add a retry mechanism for the SDIO case.
>
> If the voltage switch fails repeatedly, give up and continue the
> initialization using the original voltage.
>
> This patch places a couple of requirements on the host driver:
>
> 1) mmc_set_ios with ios.clock = 0 must gate the clock
> 2) mmc_power_off must actually cut the power to the card
> 3) The card_busy host_ops member must be implemented
>
> if these requirements are not fulfilled, the 1.8V signal voltage switch
> will still be attempted but may not be successful.
>
> Signed-off-by: Johan Rudholm <[email protected]>
> Signed-off-by: Kevin Liu <[email protected]>
> Signed-off-by: Ulf Hansson <[email protected]>
> ---
> drivers/mmc/core/core.c | 72
> ++++++++++++++++++++++++++++++++++++++++++++---
> drivers/mmc/core/sd.c | 21 ++++++++++----
> drivers/mmc/core/sdio.c | 20 +++++++++++--
> 3 files changed, 102 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
> index 285f064..e1fd9c5 100644
> --- a/drivers/mmc/core/core.c
> +++ b/drivers/mmc/core/core.c
> @@ -1223,6 +1223,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int
> signal_voltage, bool cmd11
> {
> struct mmc_command cmd = {0};
> int err = 0;
> + u32 clock;
>
> BUG_ON(!host);
>
> @@ -1231,6 +1232,16 @@ int mmc_set_signal_voltage(struct mmc_host *host, int
> signal_voltage, bool cmd11
> * 1.8V signalling.
> */
> if ((signal_voltage != MMC_SIGNAL_VOLTAGE_330) && cmd11) {
> + /*
> + * If we cannot switch voltages, return failure so the caller
> + * can continue without UHS mode
> + */
> + if (!host->ops->start_signal_voltage_switch)
> + return -EPERM;
> + if (!host->ops->card_busy)
> + pr_warning("%s: cannot verify signal voltage
> switch\n",
> + mmc_hostname(host));
> +
> cmd.opcode = SD_SWITCH_VOLTAGE;
> cmd.arg = 0;
> cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
> @@ -1241,16 +1252,69 @@ int mmc_set_signal_voltage(struct mmc_host *host, int
> signal_voltage, bool cmd11
>
> if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
> return -EIO;
> - }
>
> - host->ios.signal_voltage = signal_voltage;
> + mmc_host_clk_hold(host);
> + /*
> + * The card should drive cmd and dat[0:3] low immediately
> + * after the response of cmd11, but wait 1 ms to be sure
> + */
> + mmc_delay(1);
> + if (host->ops->card_busy && !host->ops->card_busy(host)) {
> + err = -EAGAIN;
> + goto power_cycle;
> + }
> + /*
> + * During a signal voltage level switch, the clock must be
> gated
> + * for 5 ms according to the SD spec
> + */
> + clock = host->ios.clock;
> + host->ios.clock = 0;
> + mmc_set_ios(host);
> +
> + host->ios.signal_voltage = signal_voltage;
> + err = host->ops->start_signal_voltage_switch(host,
> &host->ios);
> + if (err) {
> + /*
> + * Voltages may not been switched, but we've already
> + * sent CMD11, so a power cycle is required anyway
> + */
> + err = -EAGAIN;
> + goto power_cycle;
> + } else
> +
> + /* Keep clock gated for at least 5 ms */
> + mmc_delay(5);
> + host->ios.clock = clock;
> + mmc_set_ios(host);
> +
> + /* Wait for at least 1 ms according to spec */
> + mmc_delay(1);
>
> - if (host->ops->start_signal_voltage_switch) {
> + /*
> + * Failure to switch is indicated by the card holding
> + * dat[0:3] low
> + */
> + if (host->ops->card_busy && host->ops->card_busy(host))
> + err = -EAGAIN;
> + } else if (host->ops->start_signal_voltage_switch) {
> mmc_host_clk_hold(host);
> + host->ios.signal_voltage = signal_voltage;
> err = host->ops->start_signal_voltage_switch(host,
> &host->ios);
> - mmc_host_clk_release(host);
> + } else {
> + return 0;
> }
>
> +
> +power_cycle:
> + if (err && cmd11) {
> + pr_debug("%s: Signal voltage switch failed, "
> + "power cycling card\n", mmc_hostname(host));
> + /* Note that mmc_power_off calls mmc_set_signal_voltage */
> + mmc_power_cycle(host);
I don't like that mmc_power_cylce trigger a recursive call to this function.
How about adding a "__mmc_set_signal_voltage" function so you can
split up things more properly. I guess the cmd11 parameter might be
possible to remove in that case as well. Let's see.
> + }
> +
> + mmc_host_clk_release(host);
> +
> return err;
> }
>
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index 74972c2..874d8f6 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -713,6 +713,14 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32
> *cid, u32 *rocr)
> {
> int err;
> u32 max_current;
> + int retries = 10;
> +
> +try_again:
> + if (!retries) {
> + ocr &= ~SD_OCR_S18R;
> + pr_warning("%s: Skipping voltage switch\n",
> + mmc_hostname(host));
> + }
>
> /*
> * Since we're changing the OCR value, we seem to
> @@ -734,9 +742,10 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32
> *cid, u32 *rocr)
>
> /*
> * If the host supports one of UHS-I modes, request the card
> - * to switch to 1.8V signaling level.
> + * to switch to 1.8V signaling level. If the card has failed
> + * repeatedly to switch however, skip this.
> */
> - if (host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
> + if (retries && host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
> MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))
> ocr |= SD_OCR_S18R;
>
> @@ -748,7 +757,6 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32
> *cid, u32 *rocr)
> if (max_current > 150)
> ocr |= SD_OCR_XPC;
>
> -try_again:
> err = mmc_send_app_op_cond(host, ocr, rocr);
> if (err)
> return err;
> @@ -760,8 +768,11 @@ try_again:
> if (!mmc_host_is_spi(host) && rocr &&
> ((*rocr & 0x41000000) == 0x41000000)) {
> err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
> true);
> - if (err) {
> - ocr &= ~SD_OCR_S18R;
> + if (err == -EAGAIN) {
> + retries--;
> + goto try_again;
> + } else if (err) {
> + retries = 0;
> goto try_again;
> }
> }
> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
> index 2273ce6..39722d8 100644
> --- a/drivers/mmc/core/sdio.c
> +++ b/drivers/mmc/core/sdio.c
> @@ -583,10 +583,19 @@ static int mmc_sdio_init_card(struct mmc_host *host,
> u32 ocr,
> {
> struct mmc_card *card;
> int err;
> + int retries = 10;
>
> BUG_ON(!host);
> WARN_ON(!host->claimed);
>
> +try_again:
> + if (!retries) {
> + pr_warning("%s: Skipping voltage switch\n",
> + mmc_hostname(host));
> + ocr &= ~R4_18V_PRESENT;
> + host->ocr &= ~R4_18V_PRESENT;
> + }
> +
> /*
> * Inform the card of the voltage
> */
> @@ -645,14 +654,21 @@ static int mmc_sdio_init_card(struct mmc_host *host,
> u32 ocr,
> * systems that claim 1.8v signalling in fact do not support
> * it.
> */
> - if ((ocr & R4_18V_PRESENT) &&
> + if (!powered_resume && (ocr & R4_18V_PRESENT) &&
> (host->caps &
> (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
> MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
> MMC_CAP_UHS_DDR50))) {
> err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
> true);
> - if (err) {
> + if (err == -EAGAIN) {
> + sdio_reset(host);
> + mmc_go_idle(host);
> + mmc_send_if_cond(host, host->ocr_avail);
> + mmc_remove_card(card);
> + retries--;
> + goto try_again;
> + } else if (err) {
> ocr &= ~R4_18V_PRESENT;
> host->ocr &= ~R4_18V_PRESENT;
> }
> --
> 1.7.10
>
Kind regards
Ulf Hansson
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
