Linux-Networking Digest #213, Volume #12 Fri, 13 Aug 99 15:13:50 EDT
Contents:
Re: Difficulty with eth0 after Sound Card setup (dmalcolm)
Re: @Home Cable Modem and Linux (Roy Grimm)
Re: Q: Using Linux -computer as TDM multiplexer ? (Dave Edick)
Linux ftp slower than NT ? ([EMAIL PROTECTED])
Re: multiple PPP outgoing lines (Keith Harris)
Odd Linux Modem Error (CRC) (Bob Hart)
Re: Is 3Com's 3c905B NIC compatible with Linux? ("Cedric Blancher")
Re: Is 3Com's 3c905B NIC compatible with Linux? ([EMAIL PROTECTED])
Help to Install Network Drivers ("Ed")
Re: Windows client can't Active FTP through firewall. ("Paskal van Lomm")
Re: telnet question (Frank da Cruz)
Re: CU wedged ?????? ("William B. Arnold")
Re: Linux and MS Proxy 2.0 running on NT ("Andrey Smirnov")
Re: How to get NT Server WINS-visible across router? ("Andrey Smirnov")
More modem problems (Sean)
Re: Local network
Linux as a file server (Steve Grant)
Re: Windows Server, Linux Client? [Samba Peer to Peer? Revised] (Steve Grant)
Re: @Home Cable Modem and Linux ("Suddn")
Re: Linux as a file server (Ken Williams)
PPP module problems, part 2 (Wei-shi Tsai)
----------------------------------------------------------------------------
From: dmalcolm <[EMAIL PROTECTED]>
Crossposted-To: redhat.config,redhat.networking.general
Subject: Re: Difficulty with eth0 after Sound Card setup
Date: Fri, 13 Aug 1999 10:06:24 -0500
This is a multi-part message in MIME format.
==============58FAE8A0D552C9900DAAB55B
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
Try typing 'ifconfig'. It will tell you about your network interfaces and
weather they are enabled, IP addresses and IRQ among other things. Make sure
that the NIC and soundcard are sharing an interupt.
Dan
Hatton Humphrey wrote:
> Hi there! I've run into a rather interesting problem.
>
> I'm running Red Hat 5.2, and when I installed, I set up my NE2000
>
> compliant NIC and had the network working perfectly. It's not in a PNP
>
> mode, I had that problem already and fixed it, but something very odd
>
> occured.
>
> I noticed that the sound card had not been set up, I have a Yamaha OPL/SAx
>
> sound card, and SNDCONFIG saw it and set everything up for me. Now,
>
> however, I get a dreaded message when I boot or try to use my NIC:
>
> Delaying eth0 initialization.
>
> I'm not certian where to look or what to look for.
>
> Any suggestions?
>
> Hatton Humphrey
>
> ------------------ Posted via CNET Linux Help ------------------
> http://www.searchlinux.com
==============58FAE8A0D552C9900DAAB55B
Content-Type: text/x-vcard; charset=us-ascii;
name="dmalcolm.vcf"
Content-Transfer-Encoding: 7bit
Content-Description: Card for dmalcolm
Content-Disposition: attachment;
filename="dmalcolm.vcf"
begin:vcard
n:Malcolm;Dan
tel;fax:256-895-9934
tel;home:256-772-3109
tel;work:256-722-2840
x-mozilla-html:FALSE
org:Home
adr:;;1308 Nolan Court;Madison;AL;35758;
version:2.1
email;internet:[EMAIL PROTECTED]
title:Software Engineer/SysAdmin
x-mozilla-cpt:;25680
fn:Dan Malcolm
end:vcard
==============58FAE8A0D552C9900DAAB55B==
------------------------------
From: Roy Grimm <[EMAIL PROTECTED]>
Subject: Re: @Home Cable Modem and Linux
Date: Fri, 13 Aug 1999 09:59:14 -0500
Chad Pierce wrote:
>
> Hiya,
> I have installed Mandrake-Linux 6.0 and need help getting the @home cable
> modem to work, using my 3 Com 3C9XX ethernet card. Linux recognized the
> ethernet card, but when I go in to set up the network connection, I get no
> response from @home. Is there a trick to setting up the @home service.
> I've spent about 4 hours trying to get this to work, and am now desperate.
> I want to ditch windows, but without my cable modem, I would be lost. So I
> still have to keep it running. If anyone can help, I'd be appreciative.
> Chad
Have you set up the DHCP client? @Home gives you a dynamic IP address
through DHCP. There's a HOWTO on it somewhere...
Roy
--
"If it ain't broke, you're not tryin!" - Red Green
------------------------------
From: [EMAIL PROTECTED] (Dave Edick)
Subject: Re: Q: Using Linux -computer as TDM multiplexer ?
Reply-To: [EMAIL PROTECTED]
Date: Fri, 13 Aug 1999 14:15:54 GMT
Buy the TDM mux. There's no way you're going to get 21 interfaces on a
general purpose computer. Nor is there any existing software out for
Linux to do what you want. You'd have to build both hardware and software
from the ground up. Definitely not worth while unless you're talking about
VERY high quantities.
On Mon, 09 Aug 1999 08:03:54 GMT, [EMAIL PROTECTED] wrote:
>Hi !
>
>I am currently specifying a system where there is a need for TDM
>multiplexer that interfaces into 2 Mbps, E1, G.704 exchange. The data
>interfaces for mux are 64 kbps, X.21. The maximum number of data
>interfaces is 20.
>
>I would like to know if Linux -based computer can be used for this
>purpose or do I have to use a TDM multiplexer provided by telecom
>companies (Ericsson, Nokia, etc ...).
>
>Thanks In Advance,
>
>Markku
>
>
>
>Sent via Deja.com http://www.deja.com/
>Share what you know. Learn what you don't.
------------------------------
From: [EMAIL PROTECTED]
Subject: Linux ftp slower than NT ?
Date: Fri, 13 Aug 1999 15:58:20 GMT
Can anyone tell me why when I ftp a large file under Linux, I get ~110
kB/s but, using the same hardware, under NT4sp5 I get over 700 kB/s
sending the same file? I did the test several times to eliminate disk
access and other network traffic was nill. The remote machine was a Sun
Ultra 2/1300. The machines were connected over a single switch on the
same subnet.
Hardware:
Toshiba 660cdt
Xircom Creditcard Ethernet IIps
Software:
Linux: Debian 2.1, kernel 2.0.36, pcmcia modules 3.0.5
NT: workstation v4 service pack 5, default nt card drivers.
Linux correctly recognized the card as a xircom IIps.
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.
------------------------------
From: Keith Harris <[EMAIL PROTECTED]>
Reply-To: [EMAIL PROTECTED]
Subject: Re: multiple PPP outgoing lines
Date: Fri, 13 Aug 1999 13:08:50 -0400
Larry, D, Snyder, RN, CEN wrote:
> I have a constant PPP connection to the net and am interested in
> dynamically bringing up the 2nd line as the demand for network resouces
> increases (kind-of like bandwidth on demand, DBA or BACP with ISDN).
>
> Any leads or resoures would be appreciated..
>
> Sent via Deja.com http://www.deja.com/
> Share what you know. Learn what you don't.
Try utilizing EQL. It increases your bandwidth and works very well. See
the eql.txt.
------------------------------
From: [EMAIL PROTECTED] (Bob Hart)
Subject: Odd Linux Modem Error (CRC)
Date: 13 Aug 1999 16:57:38 GMT
I've been racking my brain over this for a week
now and would appreciate any insight.
I've been able to successfully get every
modem working in linux that I've tried, incluing
ISA and PCI modems.
Except for this one...
I'm using RH 6.0.
It's a PCI internal V.90 modem for a Transmonde
Vibrant LS laptop. Transmonde's web site and
technical support assures me (strongly) that the modem
is not a winmodem. The modem itself is
manufactured by Foresson. I use minicom
and can dial out fine, connect at around 44kbps
and can telnet adequately. Every so often
the telnet session slows down dramatically, however.
Further, when I try to use zmodem transfer in
minicom, I get about 10k of the file, and then
get error messages about "BAD CRC: Retry". A
few seconds later, a few more kbyte are transferred,
and the same error message. This happens whether
I use zmodem or xmodem. Ultimately, I end up
with transfer rates of about 0.5kbyte/second, or
about 1/8 what they should be for the connection.
I've used the same modem init string that windows
uses for the modem. When the connection
is made, I get V.42 BIS and LAPM connection messages,
so it appears the hardware settings for the modem are
ok. However, the CRC error would suggest it is
not.
I should point out that the ftp and zmodem
transfer rates in windows 98 are fine (4kbyte/second
on binary files).
These problems also impact greatly Linux ppp transfers,
which work fine otherwise. Linux ftp transfer
rates through ppp typically average the same--
about 0.5kbyte/second.
setserial autodetects the port as
uart 16550A spd_vhi
I'm at a loss to explain the errors. Anyone have
any ideas?
Thanks,
-Bob Hart
[EMAIL PROTECTED]
------------------------------
From: "Cedric Blancher" <[EMAIL PROTECTED]>
Subject: Re: Is 3Com's 3c905B NIC compatible with Linux?
Date: Fri, 13 Aug 1999 19:02:07 +0200
3Com 3c905b are handled by 3c59x "Vortex (Fast Etherlink
3c590/592/595/597) and Boomerang (Etherlink XL 3c900/905)" driver for a
long time now. This driver is shipped with linux kernel.
------------------------------
From: [EMAIL PROTECTED]
Subject: Re: Is 3Com's 3c905B NIC compatible with Linux?
Date: Fri, 13 Aug 1999 16:26:09 GMT
In article <7nepo1$o8f$[EMAIL PROTECTED]>,
"Chris" <[EMAIL PROTECTED]> wrote:
> I've got 3com's 3c905B NIC. This card is
connected to my alcatel ADSL modem.
> This modem has got 3 inputs. 1st one for 'ATM-
25' (my ATM card connects
> here), 2nd one for '10 Base-T' (my 3c905B
connects here) and third one is
> for the rj-11 line (phone line).
>
> Is there any driver that I can use to enable it
to work in Linux? I've tried
> the 3c509 and the 3c59x modules (i am using
redhat 6.0) but but gave me an
> error message saying that it was unable to load
the module.
>
> Has anybody got a similar configuration that
worked for them? Pls get back
> asap. Thanks.
>
>
Hello Chris,
I had a heck of a time figuring out what was
wrong with my 3C905B-TX NIC card. It turns out
that no driver exists for RedHat 5.2 Linux that
works properly (that I know of anyway). Luckily
for me, I had an ISA 3C509 in my other system. I
swapped them out, and then I was ok. I know that
this is not a great solution, but I had to do it
to get my systems on the network.
Rob Galante
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.
------------------------------
From: "Ed" <[EMAIL PROTECTED]>
Crossposted-To:
alt.linux,comp.linux,comp.os.linux.hardware,comp.os.linux.network,comp.os.linux.redhat
Subject: Help to Install Network Drivers
Date: Fri, 13 Aug 1999 15:01:10 +0100
I have recently installed Redhat 5.2 and i'm having a problem installing my
network drivers. I have a realtek 8029 Pci network card and the only linux
drivers i have are on a windows formatted disk.
Could someone please tell me how i can install these drivers from the disk
as i'm unable to download them from the internet.
Thanks
Ed
[EMAIL PROTECTED]
------------------------------
From: "Paskal van Lomm" <[EMAIL PROTECTED]>
Subject: Re: Windows client can't Active FTP through firewall.
Date: Fri, 13 Aug 1999 17:10:00 +0200
> Do you have the ftp module compiled and installed? Look in
> /lib/modules/(kernel version)/ipv4 for ip_masq_ftp.o.
>
This module is in that directory. (kernel 2.2.6). Why?
rgrds, paskal
------------------------------
From: [EMAIL PROTECTED] (Frank da Cruz)
Crossposted-To:
comp.os.linux.admin,comp.os.linux.help,comp.os.linux.misc,comp.os.linux.questions
Subject: Re: telnet question
Date: 13 Aug 1999 15:19:30 GMT
In article <[EMAIL PROTECTED]>, me <[EMAIL PROTECTED]> wrote:
: Is there a way to transfer files from a computer i've telnetted to, to
: my own computer ?
:
: eg. if i telnetted to server abc.com, is there a way to copy files
: directly from that computer (ie. abc.com) to my computer (ie localhost)?
:
The obvious answers are ftp, rcp, scp, etc etc. If you are asking this
question because you don't know about them, then the other responses have
already answered you.
If you are really asking: "can I transfer files over my Telnet connection?"
the answer is "yes, if you use a Telnet client that includes file transfer
capability", such as Kermit:
http://www.columbia.edu/kermit/
which is available for Windows, Linux, UNIX in general, DOS, and many other
platforms.
- Frank
------------------------------
From: "William B. Arnold" <[EMAIL PROTECTED]>
Crossposted-To: alt.os.linux
Subject: Re: CU wedged ??????
Date: Fri, 13 Aug 1999 13:04:14 -0400
M O'Neill wrote:
>
> I recently installed RH5.2 on a 486/33 with a Intel 8/16 Lantasitic NIC.
> Periodically the same message pops up. It doesn't seem to be tied to any
> particular activity I'm doing. In fact it'll just pop up when I'm not
> doing anything. The message is....
>
> CU wedged, status 0240 0000, resetting....
>
> Does anyone know what this means or what causes it? Thanks. -m
Greetings,
Humm, I've seen that before. Around a year or two ago, I was running
two Intel Ether Express nic in my linux box. Yes, I did recompile the
kernel for using the two cards. Normally, must distributed kernels
allow only one of any one particular nic to be ran at the same time.
One nic would always work flawlessly, while the second would give the
above "wedge" status. My fix after much hair pulling and way too much
coffee, was to remove the second card and replace it with another type
that I had laying around. Never had another problem. Of course during
the whole time I was also running ip aliasing. The aliasing never
seemed to be the problem, especially the "wedge" status would still
occur with only one ip per nic.
Truely, I never really found out EXACTLY what was running amiss. The
source code for the drivers were a great help in understanding how each
nic played a part in the information transfer and what ws really
happening.
Now if you happen to be using ONLY one nic, then the story is a bit
different. The above system will normally show itself using memory
mapped areas, and the mapped area overlaps into another device memory
mapped area by just a few bytes or a block. The best way to determine
if this is your case, is to take the box down to the bare bones as far
as interface cards go, pull in one at a time and see under /proc, what
linux sees as the cards properties. Once finished, do it again in
reverse order. Ensure the results are the same.
Never rule out interrupts, they can cause most suttle headaches.
Hope the above helps you in your endeavor..
Bill...
------------------------------
From: "Andrey Smirnov" <[EMAIL PROTECTED]>
Subject: Re: Linux and MS Proxy 2.0 running on NT
Date: Fri, 13 Aug 1999 10:54:05 -0700
You can't really use MS-Proxy machine as a gateway for Linux box, but you
can enable some services via proxy server.
If you only need web browsing, then simply make sure that MS-Proxy is setup
to accept anonymous authenication and point your Netscape browser to the
proxy IP address and port 80 (default).
If you want more then http service, than you need to work on configuring
MS-Proxy as a SOCKS proxy server (only in ver. 2.0!) and your machine as a
SOCKS client.
Here is a part of Proxy HOWTO, that applies to UNIX clients
(http://metalab.unc.edu/LDP/HOWTO/Firewall-HOWTO.html):
8.3 Working With a Proxy Server
Unix
To have your applications work with the proxy server, they need to be
"sockified". You will need two different telnets, one for direct
communication, one for communication via the proxy server. SOCKS comes with
instructions on how to SOCKify a program, as well as a couple pre-SOCKified
programs. If you use the SOCKified version to go somewhere direct, SOCKS
will automatically switch over to the direct version for you. Because of
this, we want to rename all the programs on our protected network and
replace them with the SOCKified programs. "Finger" becomes "finger.orig",
"telnet" becomes "telnet.orig", etc. You must tell SOCKS about each of these
via the include/socks.h file.
Certain programs will handle routing and sockifying itself. Netscape is one
of these. You can use a proxy server under Netscape by entering the server's
address (192.168.2.1 in our case) in the SOCKs field under Proxies. Each
application will need at least a little messing with, regardless of how it
handles a proxy server.
Good luck!
Jack Suddards <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> I have been following this newsgroup for a while and have seen this topic
> several times but really no definitive answer. Everyone seems to reply
with
> "do this" or "do this" but none of the "this's" ever seem to be the whole
> answer and collectively they still don't work.
>
> Has anyone actually done this - used Microsoft Proxy Server as a gateway
for
> the Linux installation? I've tried setting default gateway -I've tried
> setting the proxy info in Netscape - I've tried changing permissions on
the
> proxy server - I've tried everything I've seen on here and it still
doesn't
> work.
>
> Where can I go to get an answer?
>
> Jack Suddards.
> Linux newby - (please don't hold that against me - we all have to learn
> SOMETIME - but I'm ready to give up on Linux.!!)
>
>
>
------------------------------
From: "Andrey Smirnov" <[EMAIL PROTECTED]>
Crossposted-To: comp.protocols.smb
Subject: Re: How to get NT Server WINS-visible across router?
Date: Fri, 13 Aug 1999 11:00:32 -0700
Hello,
In order to see your NT boxes in Networkhood they need to register with WINS
server and your clients need to be pointed to the same server (or another
one, but then two WINS servers need to replicate databases!).
If your SAMBA server is the WINS server, than make sure that servers have
entry for WINS in TCP config.
It's also possible to make it work with LMHOSTS files on Windows machines,
but WINS is dynamic!
Also if you want to actually connect to those server from internal network,
you need to make sure your firewall allows SMB traffic (ports 137, 138,
139).
Good luck!
Miguel Cruz <[EMAIL PROTECTED]> wrote in message
news:_IVs3.13956$[EMAIL PROTECTED]...
>
> I have some NT servers which are on the other side of a Linux firewall
from
> the rest of the subnet. Because there was no room to allocate a subnet
just
> for these servers, the Linux machine is proxy-arping their addresses and
> forwarding the packets to its other interface.
>
> The servers work fine, participate in the domain, and so on.
>
> The only problem is that they are not visible in Network Neighborhood. How
> can I get their broadcasts to be visible to the WINS server (which is
> outside the firewall)?
>
> Can I get Linux to forward broadcasts? I can't see a good way to do it
with
> static routes, here's why:
>
> Network: 10.0.0.0
> Linux firewall: eth0 10.0.0.1
> eth1 192.168.1.1
> WINS server: 10.0.0.2
> Protected NT server: 10.0.0.3, connected to Linux eth1
>
> Can I use Samba to forward the WINS information out through the firewall
> somehow? Can I manually enter the WINS address information for the
protected
> NT server into the WINS server (NT)?
>
> miguel
------------------------------
From: Sean <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc,comp.os.linux.setup
Subject: More modem problems
Date: 13 Aug 1999 18:30:54 GMT
Thanks for those who relied to my last question although now after
asserrting my DNS info and gateway info as well domain info which I got
from my ISP. Now when trying to go to a web page (that's all I can do
since my ISP blocks all other sorts of information) it just sits there
looking up the site. Before it said I wasn't connected. Is there
anything else I must do because my ISP is really strange and blocks all
sorts of things or am I making a really stupid mistake?
================== Posted via CNET Linux Help ==================
http://www.searchlinux.com
------------------------------
From: <[EMAIL PROTECTED]>
Subject: Re: Local network
Date: 13 Aug 1999 18:30:51 GMT
Erlend Stromsvik wrote:
>
> I have 4 PC's at home and I want to run a network between them.
> I have Win98 installed on 3 of those PC's and Red Hat 6 on the last one.
> The only problem is that I cant get the Linux box to get access to the
> network. I can't ping any of the other machines but I'm able to ping my
> network card which has ip : 192.168.1.2
>
> The other machines has 192.168.1.1, .3 and .4 and they haven't got any
> problem communicating with each other.
>
> Netmask is 255.255.255.0
> Network is 192.168.1.0 (-duh :)
>
> By the way... I have a Compaq Netflex card and the driver/module for it
is
> called ThunderLan or TLAN... I think maybe there is some problem there
but I
> did use that card on another pc with Red Hat 5.2
> I get an message saying : " trying TLAN : eth0 : autonegotiation" -I got
> pissed off from this msg and commented it out from the source and
recompiled
> the module.
>
> It shouldn't be so hard setting up a local network but this time I'm
> lost.... -help!!
>
>
> stromsvik
>
>
================== Posted via CNET Linux Help ==================
http://www.searchlinux.com
------------------------------
From: Steve Grant <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Linux as a file server
Date: 13 Aug 1999 18:30:52 GMT
I am fairly new to Linux and I would eventually like to replace our Novell
file servers with Linux in a small office environment.
Is there a Windows 9x client available for this purpose? Something like
the Novell Client would be wonderful, or is it more complicated than a
simple client to access files on a Linux server from a windows network?
If you know of any freely available, I would like to get the URL so I
could give them a try at home.
Any help would be appreciated.
Thanks
Steve
================== Posted via CNET Linux Help ==================
http://www.searchlinux.com
------------------------------
From: Steve Grant <[EMAIL PROTECTED]>
Subject: Re: Windows Server, Linux Client? [Samba Peer to Peer? Revised]
Date: 13 Aug 1999 18:30:53 GMT
Marc Marais wrote:
>
>
> Chris Testa wrote in message <7oqjfa$1on$[EMAIL PROTECTED]>...
> >OK, here is my problem. For the past while I have had a LAN connecting
my
> >parents Win95 machine to my Win98 macine. The 95 machine has a
connection
> >to the phone line, and I have been using a Proxy server to connect to
that
> >machine and use the net at the same time. On Sunday I installed Red Hat
> 6.0
> >on my machine. My problem is that I want to connect to the internet
using
> >Linux through my parent's machine like I have always done, but I can't
find
> >any info on how to do it. My ISP dynamically allocates our IP address,
so
> >that complicates the matter. Basically, here's the setup:
> >
> [> /dev/null]
> >
> >- Chris
> >
For what you are describing, I have a similar setup at home and use
Winroute www.winroute.com on the gateway machine (the comp connected to
the internet) I believe there are other proxy programs out there that
will do what you need, like Wingate...
Hope this helps.
Steve
================== Posted via CNET Linux Help ==================
http://www.searchlinux.com
------------------------------
From: "Suddn" <[EMAIL PROTECTED]>
Subject: Re: @Home Cable Modem and Linux
Date: Fri, 13 Aug 1999 18:34:14 GMT
Sometimes the LAN cards that @HOME gives you, screw up. It has to do with
the PnP. You may want to disable it. I think that sometimes you need to
run a utility to do this. Maybe someone else can fill in the gaps.
Chad Pierce wrote in message ...
>Hiya,
> I have installed Mandrake-Linux 6.0 and need help getting the @home cable
>modem to work, using my 3 Com 3C9XX ethernet card. Linux recognized the
>ethernet card, but when I go in to set up the network connection, I get no
>response from @home. Is there a trick to setting up the @home service.
>I've spent about 4 hours trying to get this to work, and am now desperate.
>I want to ditch windows, but without my cable modem, I would be lost. So I
>still have to keep it running. If anyone can help, I'd be appreciative.
>Chad
>
>
------------------------------
From: [EMAIL PROTECTED] (Ken Williams)
Crossposted-To: comp.os.linux.misc
Subject: Re: Linux as a file server
Date: Fri, 13 Aug 1999 18:39:03 GMT
In article <7p1o8s$hnn$[EMAIL PROTECTED]>, Steve Grant <[EMAIL PROTECTED]> wrote:
>I am fairly new to Linux and I would eventually like to replace our Novell
>file servers with Linux in a small office environment.
>Is there a Windows 9x client available for this purpose? Something like
>the Novell Client would be wonderful, or is it more complicated than a
>simple client to access files on a Linux server from a windows network?
>If you know of any freely available, I would like to get the URL so I
>could give them a try at home.
You need to use samba on the server side and Microsoft client for Microsoft
Networks which is included in all Windows 95/98/NT's to allow the
workstations to log in. Your probably using the client for ms networks now to
share files between the workstations.
------------------------------
From: Wei-shi Tsai <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.help,comp.os.linux.questions,comp.os.linux.setup
Subject: PPP module problems, part 2
Date: Fri, 13 Aug 1999 18:38:09 GMT
This is a multi-part message in MIME format.
==============6CE1F54307DEB8BC79F84304
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
OK, I'm in trouble with my PPP modules again.
I attempted to execute pppd, but it returns that the kernel does not
support pppd. However, I know I compiled the support in the kernel! Am
I missing something?
I am using kernel version 2.2.10 and pppd version 2.3.7. I have
attached the output of lsmod and dmesg.
--
Wei-shi Tsai
Cymbeline on #descent, Kahn, and ICQ(UIN:2801023)
The Lost Material Defender Page:
http://www.crosswinds.net/dallas/~perdita/index.html
MoonieCode(1.8.11):
SM:5+ F:sMe++>Mo+>:vZo<Bl+>:aLu+Ry+:pClR2 D:sMa<:vBe-Wi-> X:a0s|35d++
O:d+:s?:?o?:a--:h--- P:a+:s6:w-:f?:eBrD:hBkm:t-:cAs:y---:r+|
==============6CE1F54307DEB8BC79F84304
Content-Type: text/plain; charset=us-ascii;
name="Lsmod"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="Lsmod"
perdita:~# lsmod
Module Size Used by
v_midi 4672 0 (unused)
opl3 10264 0 (unused)
mpu401 17668 0 (unused)
sb 31528 0 (unused)
uart401 5628 0 [sb]
sound 55128 0 [v_midi opl3 mpu401 sb uart401]
soundcore 2208 7 [sb sound]
bsd_comp 3468 0 (unused)
ppp 19412 0 [bsd_comp]
slhc 4188 0 [ppp]
perdita:~#
==============6CE1F54307DEB8BC79F84304
Content-Type: text/plain; charset=us-ascii;
name="Dmesg"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="Dmesg"
Linux version 2.2.10 (root@perdita) (gcc version 2.7.2.3) #7 Fri Aug 13 10:46:08 CDT
1999
Detected 200459351 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 399.77 BogoMIPS
Memory: 30640k/32704k available (1040k kernel code, 412k reserved, 556k data, 56k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium MMX stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfdba1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
parport0: PC-style at 0x3bc [SPP]
parport0: no IEEE-1284 device present.
parport1: PC-style at 0x378 [SPP,PS2]
parport1: no IEEE-1284 device present.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
lp1: using parport1 (polling).
loop: registered device at major 7
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC34300L, ATA DISK drive
hdb: FX240S, ATAPI CDROM drive
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: WDC AC34300L, 4104MB w/256kB Cache, CHS=523/255/63, UDMA
hdb: ATAPI 24X CD-ROM drive, 256kB Cache
Uniform CDROM driver Revision: 2.55
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ppa: Version 2.03 (for Linux 2.2.x)
WARNING - no ppa compatible devices found.
As of 31/Aug/1998 Iomega started shipping parallel
port ZIP drives with a different interface which is
supported by the imm (ZIP Plus) driver. If the
cable is marked with "AutoDetect", this is what has
happened.
imm: Version 2.03 (for Linux 2.0.0)
imm: No devices found, aborting driver load.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: hda1 hda2 hda3
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 56k freed
Adding Swap: 64256k swap-space (priority -1)
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
PPP BSD Compression module registered
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 3.01 detected OK (240)
ESS chip ES1688 detected (kernel 2.0 compatible)
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
MIDI Loopback device driver
js: Version 1.2.13 using 200 MHz RDTSC timer.
joy-analog: no joysticks found
VFS: Disk change detected on device ide0(3,64)
==============6CE1F54307DEB8BC79F84304==
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.networking) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Networking Digest
******************************
