:-)
Haines Brown wrote: > > Chuck, > > > Date: Sun, 24 Nov 2002 13:55:11 -0500 > > From: Chuck Gelm <[EMAIL PROTECTED]> > > X-Accept-Language: en > > CC: [EMAIL PROTECTED] > > > > Please address your linux-newbie messages to > > [EMAIL PROTECTED] and not to > > [EMAIL PROTECTED] and not to [EMAIL PROTECTED] without > > [EMAIL PROTECTED] > > > > as I cannot 'reply' to [EMAIL PROTECTED] without adding > > that address manually & I see no reason to reply to you alone. > > > > If you cannot do this, I'll edit to suit. ;-) > > Chuck. I quite understand. Somehow a CC: [EMAIL PROTECTED] > got in there, and so when I replied, it was reproduced. The header of > this message looks clean, and so it's a kind of test. It goes to you, > and a CC: for the list and back to me. > > > Yes, AFAIK, the eth# device that PPPOE is going to use should be > > up. However, it should not have an IP address. > > Yes, the eth0 is up and running. The problem was that the > configuration utility gave me the choice of a static address or DHCP, > and I was unable to enter " ". I can get back to the files themselves, > but right now on the machine I'm using, I have a permanent address for > my machine (192.168.0.1) that is simply ignored when I set up a DSL > connection. To remove the IPADDRESS from eth0, do ifconfig eth0 down ifconfig eth0 0.0.0.0 up > > > Actually, when I run redhat-configuration-network, I see not only > > > eth0, but also ppp0 > > I simply killed that unwanted ppp0, and it goes better. > > > Who is running Red Hat 8.0 and Roaring Penguin? > > 15% of all linux users? ;-) Naw, not how many or percentile, but who, specifically, can help us with a replica of your system. ;-) > With eth0 up and running, and having defined the inteface property in > network configuration, I then proceed to configure Roaring Penguin. > > Before I do I run adsl-status and am told, naturally, that there's no > /etc/ppp/pppoe.conf file. I then proceed to configure Roaring Penguin > (I'm comfortable with that), and at the end save the > configuration. However, no /etc/ppp/pppoe.conf file shows up. locate pppoe.conf on my system reports: /etc/ppp/pppoe.conf /usr/local/rp-pppoe-3.5/configs/pppoe.conf I think that 'adsl-setup' should have created a 'pppoe.conf' file. Where it was placed, I'm not sure. > Then I start adsl and get: ipchains: protocol not available. My first > reaction was that iptables were blocking ppp, but now I don't think > so. > I think that IPTABLES is blocking IPCHAINS. - I think that the default Red Hat 8.0 kernel uses IPTABLES and not IPCHAINS. - I think that rp-pppoe_v3.x uses IPCHAINS and not IPTABLES. - I think that when (if?) adsl-setup creates an IPCHAINS ruleset it is useless to your kernel as your kernel is expecting an IPTABLES ruleset. :-| > Nevertheless, when I run > > ipchains -L ... REJECT tcp anysource anydest tcp > flags:SYN,RSG,AC... > > However, I can read the error above to mean that ipchains is telling > me there's no ppp protocol running. That, with the absense of a > configuraion file, suggests that Roaring Penguin failed to configure > pppoe. I did all this as root, but I'll have to check permissions, > etc. to make sure the configuration file can be created. Also, I can > try importing my old config file, which should be the same. > > Haines Give Ray what he asked for. "uname -a", "ifconfig -a", & "netstat -nr". I've edited some IP addresses. Here are mine: Linux firewall 2.2.19.firewall #8 Wed Aug 28 18:23:22 EDT 2002 i486 unknown Chain input (policy ACCEPT): target prot opt source destination ports DENY udp ----l- anywhere anywhere any -> 0:1023 DENY tcp ----l- anywhere anywhere any -> 0:1023 DENY tcp -y--l- anywhere anywhere any -> any DENY icmp ----l- anywhere anywhere echo-request Chain forward (policy DENY): target prot opt source destination ports MASQ all ------ anywhere anywhere n/a Chain output (policy ACCEPT): Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 000.72.131.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 000.72.131.1 0.0.0.0 UG 0 0 0 ppp0 And here is my pppoe.conf for your perusal: ETH='eth1' USER='[EMAIL PROTECTED]' DEMAND=no DNSTYPE=NOCHANGE PEERDNS=no DNS1= DNS2= 000.000.000.000 ;-) DEFAULTROUTE=yes CONNECT_TIMEOUT=30 CONNECT_POLL=2 ACNAME= SERVICENAME= PING="." CF_BASE=`basename $CONFIG` PIDFILE="/var/run/$CF_BASE-adsl.pid" SYNCHRONOUS=no CLAMPMSS=1412 LCP_INTERVAL=20 LCP_FAILURE=3 PPPOE_TIMEOUT=80 FIREWALL=MASQUERADE ; <---- see /etc/ppp/firewall-standalone LINUX_PLUGIN= PPPOE_EXTRA="" PPPD_EXTRA="" HTH, Chuck - To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.linux-learn.org/faqs
