* Felipe Balbi <[EMAIL PROTECTED]> [080419 13:12]: > On Sat, Apr 19, 2008 at 09:24:50PM +0530, Syed Mohammed, Khasim wrote: > > > > > > > -----Original Message----- > > > From: Felipe Balbi [mailto:[EMAIL PROTECTED] > > > Sent: Saturday, April 19, 2008 6:22 PM > > > To: Tony Lindgren > > > Cc: Felipe Balbi; Syed Mohammed, Khasim; [email protected]; > > > [EMAIL PROTECTED] > > > Subject: Re: [PATCH 3/4] Adding support for OMAP3 Beagle Board > > > > > > On Fri, Apr 18, 2008 at 12:05:54PM -0700, Tony Lindgren wrote: > > > > > > +#ifndef __ASM_ARCH_OMAP3_BEAGLE_H > > > > > > +#define __ASM_ARCH_OMAP3_BEAGLE_H > > > > > > + > > > > > > +#ifdef CONFIG_TWL4030_CORE > > > > > > + > > > > > > +#define TWL4030_IRQNUM INT_34XX_SYS_NIRQ > > > > > > + > > > > > > +/* TWL4030 Primary Interrupt Handler (PIH) interrupts */ > > > > > > +#define IH_TWL4030_BASE IH_BOARD_BASE > > > > > > +#define IH_TWL4030_END (IH_TWL4030_BASE+8) > > > > > > +#define IH_TWL4030_PWRBASE (IH_TWL4030_END) > > > > > > +#define IH_TWL4030_PWRBASE_END (IH_TWL4030_PWRBASE+8) > > > > > > + > > > > > > +#ifdef CONFIG_TWL4030_GPIO > > > > > > +/* TWL4030 GPIO Interrupts */ > > > > > > +#define IH_TWL4030_GPIO_BASE (IH_TWL4030_PWRBASE_END) > > > > > > +#define IH_TWL4030_GPIO_END (IH_TWL4030_GPIO_BASE+18) > > > > > > +#define NR_IRQS (IH_TWL4030_GPIO_END) > > > > > > +#else > > > > > > +#define NR_IRQS (IH_TWL4030_PWRBASE_END) > > > > > > +#endif /* CONFIG_I2C_TWL4030_GPIO */ > > > > > > > > > > shouldn't you consider the power base as the other boards ? > > > > > > > > Felipe, can you clarify what you mean here? > > > > > > Just check board-3430sdp.h > > > > > > #ifdef CONFIG_TWL4030_CORE > > > > > > #define TWL4030_IRQNUM INT_34XX_SYS_NIRQ > > > > > > /* TWL4030 Primary Interrupt Handler (PIH) interrupts */ > > > #define IH_TWL4030_BASE IH_BOARD_BASE > > > #define IH_TWL4030_END (IH_TWL4030_BASE+8) > > > > > > #define IH_TWL4030_PWRBASE (IH_TWL4030_END) > > > #define IH_TWL4030_PWRBASE_END (IH_TWL4030_PWRBASE+8) > > > > > > #ifdef CONFIG_TWL4030_GPIO > > > > > > /* TWL4030 GPIO Interrupts */ > > > #define IH_TWL4030_GPIO_BASE (IH_TWL4030_PWRBASE_END) > > > #define IH_TWL4030_GPIO_END (IH_TWL4030_GPIO_BASE+18) > > > #define NR_IRQS (IH_TWL4030_GPIO_END) > > > #else > > > #define NR_IRQS (IH_TWL4030_PWRBASE_END) > > > #endif /* CONFIG_I2C_TWL4030_GPIO */ > > > #endif /* End of support for TWL4030 */ > > > #endif /* __ASM_ARCH_OMAP_3430SDP_H */ > > > > > > if there are no such defines for power base, it will break compilation > > > of twl4030-pwrirq.c which is always built whenever we enable twl4030 > > > support. > > > > > > > At present I have enabled TWL4030 support in both EVM and beagle patches > > and it is tested booting on both beagle and evm boards, "with out these > > defines". > > > > So, these defines are not required now. They will be added when necessary > > along with relevant functionality. I could have added but then your comment > > might have been, why to add these defines when they are not used :) > > I can't see how can you possibly build twl4030 support without those > defines. Looking at > drivers/i2c/chips/twl4030-pwrirq.c:twl4030_pwrirq_enableint(): > > static void twl4030_pwrirq_enableint(unsigned int irq) > { > twl4030_pwrirq_pending_unmask |= 1 << (irq - IH_TWL4030_PWRBASE); > if (twl4030_pwrirq_unmask_thread && > twl4030_pwrirq_unmask_thread->state != TASK_RUNNING) > wake_up_process(twl4030_pwrirq_unmask_thread); > } > > I clearly see the use of IH_TWL4030_PWRBASE and looking at > drivers/i2c/chips/Makefile: > > obj-$(CONFIG_TWL4030_CORE) += twl4030-core.o twl4030-pwrirq.o > > I also clearly see that compilation it will always fail whenever you enable > CONFIG_TWL4030_CORE. > > But you already put such defines anyway :-p
OK, PWRBASE is now defined, pushing these today. Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
