"ext Tony Lindgren" <[EMAIL PROTECTED]> writes:
> Hi,
>
> * Jouni Hogander <[EMAIL PROTECTED]> [080516 03:57]:
>> Add common omap2/3 function to check wether there is irq pending.
>> Switch to use it in omap2 pm code instead of its own.
>>
>> Signed-off-by: Jouni Hogander <[EMAIL PROTECTED]>
>> ---
>> arch/arm/mach-omap2/irq.c | 29 +++++++++++++++++++++++------
>> arch/arm/mach-omap2/pm24xx.c | 19 +++----------------
>> include/asm-arm/arch-omap/irqs.h | 1 +
>> 3 files changed, 27 insertions(+), 22 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c
>> index ac062ee..f1e1e2e 100644
>> --- a/arch/arm/mach-omap2/irq.c
>> +++ b/arch/arm/mach-omap2/irq.c
>> @@ -20,12 +20,13 @@
>>
>> /* selected INTC register offsets */
>>
>> -#define INTC_REVISION 0x0000
>> -#define INTC_SYSCONFIG 0x0010
>> -#define INTC_SYSSTATUS 0x0014
>> -#define INTC_CONTROL 0x0048
>> -#define INTC_MIR_CLEAR0 0x0088
>> -#define INTC_MIR_SET0 0x008c
>> +#define INTC_REVISION 0x0000
>> +#define INTC_SYSCONFIG 0x0010
>> +#define INTC_SYSSTATUS 0x0014
>> +#define INTC_CONTROL 0x0048
>> +#define INTC_MIR_CLEAR0 0x0088
>> +#define INTC_MIR_SET0 0x008c
>> +#define INTC_PENDING_IRQ0 0x0098
>>
>> /*
>> * OMAP2 has a number of different interrupt controllers, each interrupt
>> @@ -122,6 +123,22 @@ static void __init omap_irq_bank_init_one(struct
>> omap_irq_bank *bank)
>> intc_bank_write_reg(1 << 0, bank, INTC_SYSCONFIG);
>> }
>>
>> +int omap_irq_pending(void)
>> +{
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
>> + struct omap_irq_bank *bank = irq_banks + i;
>> + int irq;
>> +
>> + for (irq = 0; irq < bank->nr_irqs; irq += 32)
>> + if (intc_bank_read_reg(bank, INTC_PENDING_IRQ0 +
>> + ((irq >> 5) << 5)))
>> + return 1;
>> + }
>> + return 0;
>> +}
>> +
>
> In this case it should be enough to know if anything is set in the
> bank registers, so you should be able to leave out the second for loop.
> At most you need to read only the four bank registers. No need to check
> for individual interrupts.
Current code is presenting each interrupt controller as a bank. I
think in TRM they are talking about banks in each controller. So there
is three banks in mpu intc 0..2. This is in arch/arm/mach-omap2/irq.c:
* OMAP2 has a number of different interrupt controllers, each interrupt
* controller is identified as its own "bank". Register definitions are
* fairly consistent for each bank, but not all registers are implemented
* for each bank.. when in doubt, consult the TRM.
*/
So the first loop is going through controllers which is only mpu
intc. Second loop is going through bank registers. I'm using irq only
for finding out right offset for bank register. This is another
implementation. Which does exactly same thing:
int omap_irq_pending(void)
{
int i, j;
for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
struct omap_irq_bank *bank = irq_banks + i;
for (j = 0; j < 3; j++)
if (intc_bank_read_reg(bank, INTC_PENDING_IRQ0 +
0x20 * j))
return 1;
}
return 0;
}
If you think this is better I can change it. In first version I was
just trying to follow practices used in irq.c for finding out offsets.
--
Jouni Högander
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
