Hi,
Sorry for the delay on looking at this, it's looking pretty good in
general. Few more mostly cosmetic comments below.
* Tero Kristo <[EMAIL PROTECTED]> [080603 01:53]:
> UART usage (e.g. serial console) now denies sleep for 5 seconds. This
> makes it possible to use serial console when dynamic idle is enabled.
>
> Also moved code from pm-debug.c to serial.c, and made pm24xx.c use this
> new implementation.
>
> Signed-off-by: Tero Kristo <[EMAIL PROTECTED]>
> ---
> arch/arm/mach-omap2/pm-debug.c | 132
> ------------------------------------
> arch/arm/mach-omap2/pm.h | 8 --
> arch/arm/mach-omap2/pm24xx.c | 53 ++++++++++-----
> arch/arm/mach-omap2/pm34xx.c | 5 ++
> arch/arm/mach-omap2/serial.c | 118 ++++++++++++++++++++++++++++++++
> include/asm-arm/arch-omap/common.h | 3 +
> 6 files changed, 162 insertions(+), 157 deletions(-)
>
<snip>
> diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
> index b0fa582..65571f9 100644
> --- a/arch/arm/mach-omap2/serial.c
> +++ b/arch/arm/mach-omap2/serial.c
> @@ -23,8 +23,47 @@
> #include <asm/arch/common.h>
> #include <asm/arch/board.h>
>
> +#include "prm.h"
> +#include "pm.h"
> +
> +#define SERIAL_AWAKE_TIME 5
> +
> static struct clk *uart_ick[OMAP_MAX_NR_PORTS];
> static struct clk *uart_fck[OMAP_MAX_NR_PORTS];
> +static s64 omap_serial_next_sleep;
> +
> +static const u32 omap2_uart_wk_st[OMAP_MAX_NR_PORTS] = {
> + PM_WKST1, PM_WKST1, OMAP24XX_PM_WKST2
> +};
> +static const u32 omap2_uart_wk_en[OMAP_MAX_NR_PORTS] = {
> + PM_WKEN1, PM_WKEN1, OMAP24XX_PM_WKEN2
> +};
> +const u32 omap2_uart_wk_bit[OMAP_MAX_NR_PORTS] = {
> + OMAP24XX_ST_UART1, OMAP24XX_ST_UART2, OMAP24XX_ST_UART3
> +};
> +
> +#if defined(CONFIG_ARCH_OMAP2)
> +static const u32 omap_uart_fclk_mask[OMAP_MAX_NR_PORTS] = {
> + OMAP24XX_EN_UART1, OMAP24XX_EN_UART2, OMAP24XX_EN_UART3
> +};
> +#endif
> +
> +#if defined(CONFIG_ARCH_OMAP3)
> +static const u32 omap_uart_fclk_mask[OMAP_MAX_NR_PORTS] = {
> + OMAP3430_EN_UART1, OMAP3430_EN_UART2, OMAP3430_EN_UART3
> +};
The above should be omap24xx_uart_fclk_mask and omap34xx_uart_fclk_mask.
Otherwise we cannot compile in both 24xx and 34xx into the same kernel.
> +/* UART padconfig registers, these may differ if non-default padconfig
> + is used */
> +#define CONTROL_PADCONF_UART1_RX 0x48002182
> +#define CONTROL_PADCONF_UART2_RX 0x4800217A
> +#define CONTROL_PADCONF_UART3_RX 0x4800219E
> +#define PADCONF_WAKEUP_ST 0x8000
> +
> +static const u32 omap_uart_padconf[OMAP_MAX_NR_PORTS] = {
> + CONTROL_PADCONF_UART1_RX, CONTROL_PADCONF_UART2_RX,
> CONTROL_PADCONF_UART3_RX
> +};
> +#endif
This should be omap34xx_uart_padconf is only used for 34xx. Also, it's
currently not defined for 24xx and breaks build.
> static struct plat_serial8250_port serial_platform_data[] = {
> {
> @@ -83,6 +122,15 @@ static inline void __init omap_serial_reset(struct
> plat_serial8250_port *p)
> serial_write_reg(p, UART_OMAP_SYSC, (0x02 << 3) | (1 << 2) | (1 << 0));
> }
>
> +static void omap_serial_kick(void)
> +{
> + struct timespec t;
> +
> + getnstimeofday(&t);
> + omap_serial_next_sleep = timespec_to_ns(&t) +
> + (s64)SERIAL_AWAKE_TIME * (s64)1000000000;
> +}
> +
> void omap_serial_enable_clocks(int enable)
> {
> int i;
> @@ -99,6 +147,71 @@ void omap_serial_enable_clocks(int enable)
> }
> }
>
> +void omap_serial_fclk_mask(u32 *f1, u32 *f2)
> +{
> + if (uart_ick[0])
> + *f1 &= ~omap_uart_fclk_mask[0];
> + if (uart_ick[1])
> + *f1 &= ~omap_uart_fclk_mask[1];
> + if (uart_ick[2])
> + *f2 &= ~omap_uart_fclk_mask[2];
> +}
> +
> +void omap_serial_check_wakeup(void)
> +{
> + int i;
> +
> + if (cpu_is_omap34xx())
> + for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
> + if (!uart_ick[i])
> + continue;
> + if (omap_readw(omap_uart_padconf[i]) &
> PADCONF_WAKEUP_ST)
> + omap_serial_kick();
> + return;
> + }
The formatting for return above looks one tab too much to the right?
> + if (cpu_is_omap24xx()) {
> + u32 l;
> +
> + for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
> + if (!uart_ick[i])
> + continue;
> + l = prm_read_mod_reg(CORE_MOD, omap2_uart_wk_st[i]);
> + if (l & omap2_uart_wk_bit[i])
> + omap_serial_kick();
> + return;
> + }
> + }
> +}
Here too.
> +int omap_serial_can_sleep(void)
> +{
> + s64 cnt;
> + int i;
> + struct timespec t;
> +
> + struct plat_serial8250_port *p = serial_platform_data;
> +
> + getnstimeofday(&t);
> + cnt = timespec_to_ns(&t);
> +
> + for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
> + if (!uart_ick[i])
> + continue;
> + /* Check if we have data in the transmit buffer */
> + if ((serial_read_reg(p + i, UART_LSR) &
> (UART_LSR_TEMT|UART_LSR_THRE))
> + != (UART_LSR_TEMT|UART_LSR_THRE)) {
> + omap_serial_kick();
> + return 0;
> + }
> + }
> +
> + if (omap_serial_next_sleep - cnt >= 0)
> + return 0;
> +
> + return 1;
> +}
> +
> void __init omap_serial_init(void)
> {
> int i;
> @@ -142,7 +255,12 @@ void __init omap_serial_init(void)
> clk_enable(uart_fck[i]);
>
> omap_serial_reset(p);
> +
> + if (cpu_is_omap24xx())
> + prm_set_mod_reg_bits(omap2_uart_wk_bit[i], CORE_MOD,
> omap2_uart_wk_en[i]);
> }
How about run the patch through checkpatch.pl, this line looks too long?
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
