* David Brownell <[EMAIL PROTECTED]> [081016 12:34]:
> From: David Brownell <[EMAIL PROTECTED]>
>
> Simplify handling of VBUS and ID status and the USB_PRES interrupt.
> This seems to resolve the problems I previously saw on Beagle and
> Overo boards.
>
> - Read the status directly, instead of trying to infer it from
> dodgey side effects of IRQ handling and trigger tweaking.
>
> - Stop trying to arrange those dodgey side effects; just leave
> the IRQ enabled at all times.
>
> - Check that status as part of driver probe, so the PHY can
> always be active by the time it's needed. (BUGFIX!)
>
> - Re-sequence probe() to be less racey, and to avoid duplicating
> logic found elsewhere (notably irq handling and PHY activation).
>
> - Make the irq_chip be the exclusive owner of PWR_EDR (finally).
>
> - Get rid of needless work_struct ... in this irq handling thread,
> it's safe and cheap to call sysfs_notify() directly.
>
> Stop enabling IRQs on the USB subchip. There's no IRQ handler for
> them, and since ALT_INT_REROUTE isn't being set they'll never
> arrive ... so there's no point to enabling them.
>
> Also add some comments about other things such an otg_transciever
> driver should be doing, fixing minor omissions; and remove some
> unnecessary file inclusions.
Pushing today, I guess that's it for the USB problems for now.
Tony
>
> Signed-off-by: David Brownell <[EMAIL PROTECTED]>
> ---
> NOTE: applies on top of the previous patches updating IRQ
> handling and creating drivers/mfd/twl4030-irq.c ...
>
> drivers/i2c/chips/twl4030-usb.c | 209 ++++++++++++++++++--------------------
> 1 file changed, 104 insertions(+), 105 deletions(-)
>
> --- a/drivers/i2c/chips/twl4030-usb.c
> +++ b/drivers/i2c/chips/twl4030-usb.c
> @@ -26,16 +26,12 @@
>
> #include <linux/module.h>
> #include <linux/init.h>
> -#include <linux/time.h>
> #include <linux/interrupt.h>
> -#include <linux/irq.h>
> #include <linux/platform_device.h>
> #include <linux/spinlock.h>
> #include <linux/workqueue.h>
> #include <linux/io.h>
> -#include <linux/usb.h>
> -#include <linux/usb/ch9.h>
> -#include <linux/usb/gadget.h>
> +#include <linux/delay.h>
> #include <linux/usb/otg.h>
> #include <linux/i2c/twl4030.h>
> #include <mach/usb.h>
> @@ -237,10 +233,6 @@
> #define PMBR1 0x0D
> #define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
>
> -/* In module TWL4030_MODULE_INT */
> -#define REG_PWR_EDR1 0x05
> -#define USB_PRES_FALLING (1 << 4)
> -#define USB_PRES_RISING (1 << 5)
>
> /* bits in OTG_CTRL */
> #define OTG_XCEIV_OUTPUTS \
> @@ -256,8 +248,14 @@
> OTG_CTRL_BITS)
>
>
> +enum linkstat {
> + USB_LINK_UNKNOWN = 0,
> + USB_LINK_NONE,
> + USB_LINK_VBUS,
> + USB_LINK_ID,
> +};
> +
> struct twl4030_usb {
> - struct work_struct irq_work;
> struct otg_transceiver otg;
> struct device *dev;
>
> @@ -267,8 +265,8 @@ struct twl4030_usb {
> /* pin configuration */
> enum twl4030_usb_mode usb_mode;
>
> - unsigned vbus:1;
> int irq;
> + u8 linkstat;
> u8 asleep;
> bool irq_enabled;
> };
> @@ -326,21 +324,27 @@ static inline int twl4030_usb_write(stru
> return ret;
> }
>
> -static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
> +static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8
> address)
> {
> u8 data;
> int ret = 0;
>
> - ret = twl4030_i2c_read_u8(TWL4030_MODULE_USB, &data, address);
> + ret = twl4030_i2c_read_u8(module, &data, address);
> if (ret >= 0)
> ret = data;
> else
> dev_warn(twl->dev,
> - "TWL4030:USB:Read[0x%x] Error %d\n", address, ret);
> + "TWL4030:readb[0x%x,0x%x] Error %d\n",
> + module, address, ret);
>
> return ret;
> }
>
> +static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
> +{
> + return twl4030_readb(twl, TWL4030_MODULE_USB, address);
> +}
> +
> /*-------------------------------------------------------------------------*/
>
> static inline int
> @@ -357,6 +361,39 @@ twl4030_usb_clear_bits(struct twl4030_us
>
> /*-------------------------------------------------------------------------*/
>
> +static enum linkstat twl4030_usb_linkstat(struct twl4030_usb *twl)
> +{
> + int status;
> + int linkstat = USB_LINK_UNKNOWN;
> +
> + /* STS_HW_CONDITIONS */
> + status = twl4030_readb(twl, TWL4030_MODULE_PM_MASTER, 0x0f);
> + if (status < 0)
> + dev_err(twl->dev, "USB link status err %d\n", status);
> + else if (status & BIT(7))
> + linkstat = USB_LINK_VBUS;
> + else if (status & BIT(2))
> + linkstat = USB_LINK_ID;
> + else
> + linkstat = USB_LINK_NONE;
> +
> + dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
> + status, status, linkstat);
> +
> + spin_lock_irq(&twl->lock);
> + twl->linkstat = linkstat;
> + if (linkstat == USB_LINK_ID) {
> + twl->otg.default_a = true;
> + twl->otg.state = OTG_STATE_A_IDLE;
> + } else {
> + twl->otg.default_a = false;
> + twl->otg.state = OTG_STATE_B_IDLE;
> + }
> + spin_unlock_irq(&twl->lock);
> +
> + return linkstat;
> +}
> +
> static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
> {
> twl->usb_mode = mode;
> @@ -410,24 +447,6 @@ static void twl4030_i2c_access(struct tw
> }
> }
>
> -static void usb_irq_enable(struct twl4030_usb *twl, int trigger)
> -{
> - set_irq_type(twl->irq, trigger);
> -
> - if (!twl->irq_enabled) {
> - enable_irq(twl->irq);
> - twl->irq_enabled = true;
> - }
> -}
> -
> -static void usb_irq_disable(struct twl4030_usb *twl)
> -{
> - if (twl->irq_enabled) {
> - disable_irq(twl->irq);
> - twl->irq_enabled = false;
> - }
> -}
> -
> static void twl4030_phy_power(struct twl4030_usb *twl, int on)
> {
> u8 pwr;
> @@ -448,16 +467,9 @@ static void twl4030_phy_power(struct twl
>
> static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
> {
> - if (controller_off)
> - usb_irq_disable(twl);
> -
> if (twl->asleep)
> return;
>
> - if (!controller_off)
> - /* enable rising edge interrupt to detect cable attach */
> - usb_irq_enable(twl, IRQ_TYPE_EDGE_RISING);
> -
> twl4030_phy_power(twl, 0);
> twl->asleep = 1;
> }
> @@ -467,9 +479,6 @@ static void twl4030_phy_resume(struct tw
> if (!twl->asleep)
> return;
>
> - /* enable falling edge interrupt to detect cable detach */
> - usb_irq_enable(twl, IRQ_TYPE_EDGE_FALLING);
> -
> twl4030_phy_power(twl, 1);
> twl4030_i2c_access(twl, 1);
> twl4030_usb_set_mode(twl, twl->usb_mode);
> @@ -514,25 +523,18 @@ static ssize_t twl4030_usb_vbus_show(str
> int ret = -EINVAL;
>
> spin_lock_irqsave(&twl->lock, flags);
> - ret = sprintf(buf, "%s\n", twl->vbus ? "on" : "off");
> + ret = sprintf(buf, "%s\n",
> + (twl->linkstat == USB_LINK_VBUS) ? "on" : "off");
> spin_unlock_irqrestore(&twl->lock, flags);
>
> return ret;
> }
> static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
>
> -static void twl4030_usb_irq_work(struct work_struct *work)
> -{
> - struct twl4030_usb *twl = container_of(work,
> - struct twl4030_usb, irq_work);
> -
> - sysfs_notify(&twl->dev->kobj, NULL, "vbus");
> -}
> -
> static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
> {
> struct twl4030_usb *twl = _twl;
> - u8 val;
> + int status;
>
> #ifdef CONFIG_LOCKDEP
> /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which
> @@ -542,27 +544,28 @@ static irqreturn_t twl4030_usb_irq(int i
> local_irq_enable();
> #endif
>
> - /* FIXME stop accessing PWR_EDR1 ... if nothing else, we
> - * know which edges we told the IRQ to trigger on. And
> - * there seem to be OTG_specific registers and irqs that
> - * provide the right info without guessing like this:
> - * USB_INT_STS, ID_STATUS, STS_HW_CONDITIONS, etc.
> - */
> + status = twl4030_usb_linkstat(twl);
> + if (status != USB_LINK_UNKNOWN) {
>
> - /* action based on cable attach or detach */
> - WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
> - &val, REG_PWR_EDR1) < 0);
> + /* FIXME add a set_power() method so that B-devices can
> + * configure the charger appropriately. It's not always
> + * correct to consume VBUS power, and how much current to
> + * consume is a function of the USB configuration chosen
> + * by the host.
> + *
> + * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
> + * its disconnect() sibling, when changing to/from the
> + * USB_LINK_VBUS state. musb_hdrc won't care until it
> + * starts to handle softconnect right.
> + */
> + twl4030charger_usb_en(status == USB_LINK_VBUS);
>
> - if (val & USB_PRES_RISING) {
> - twl4030_phy_resume(twl);
> - twl4030charger_usb_en(1);
> - twl->vbus = 1;
> - } else {
> - twl4030charger_usb_en(0);
> - twl->vbus = 0;
> - twl4030_phy_suspend(twl, 0);
> + if (status == USB_LINK_NONE)
> + twl4030_phy_suspend(twl, 0);
> + else
> + twl4030_phy_resume(twl);
> }
> - schedule_work(&twl->irq_work);
> + sysfs_notify(&twl->dev->kobj, NULL, "vbus");
>
> return IRQ_HANDLED;
> }
> @@ -608,11 +611,6 @@ static int twl4030_set_peripheral(struct
>
> twl->otg.state = OTG_STATE_B_IDLE;
>
> - twl4030_usb_set_bits(twl, USB_INT_EN_RISE,
> - USB_INT_SESSVALID | USB_INT_VBUSVALID);
> - twl4030_usb_set_bits(twl, USB_INT_EN_FALL,
> - USB_INT_SESSVALID | USB_INT_VBUSVALID);
> -
> return 0;
> }
>
> @@ -639,8 +637,7 @@ static int twl4030_set_host(struct otg_t
> twl4030_usb_set_bits(twl, TWL4030_OTG_CTRL,
> TWL4030_OTG_CTRL_DMPULLDOWN
> | TWL4030_OTG_CTRL_DPPULLDOWN);
> - twl4030_usb_set_bits(twl, USB_INT_EN_RISE, USB_INT_IDGND);
> - twl4030_usb_set_bits(twl, USB_INT_EN_FALL, USB_INT_IDGND);
> +
> twl4030_usb_set_bits(twl, FUNC_CTRL, FUNC_CTRL_SUSPENDM);
> twl4030_usb_set_bits(twl, TWL4030_OTG_CTRL, TWL4030_OTG_CTRL_DRVVBUS);
>
> @@ -651,8 +648,7 @@ static int __init twl4030_usb_probe(stru
> {
> struct twl4030_usb_data *pdata = pdev->dev.platform_data;
> struct twl4030_usb *twl;
> - int status;
> - u8 vbus;
> + int status;
>
> twl = kzalloc(sizeof *twl, GFP_KERNEL);
> if (!twl)
> @@ -663,26 +659,38 @@ static int __init twl4030_usb_probe(stru
> return -EINVAL;
> }
>
> - WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
> - &vbus, REG_PWR_EDR1) < 0);
> - vbus &= USB_PRES_RISING;
> -
> twl->dev = &pdev->dev;
> twl->irq = platform_get_irq(pdev, 0);
> + twl->otg.dev = twl->dev;
> + twl->otg.label = "twl4030";
> twl->otg.set_host = twl4030_set_host;
> twl->otg.set_peripheral = twl4030_set_peripheral;
> twl->otg.set_suspend = twl4030_set_suspend;
> twl->usb_mode = pdata->usb_mode;
> - twl->vbus = vbus ? 1 : 0;
> + twl->asleep = 1;
>
> /* init spinlock for workqueue */
> spin_lock_init(&twl->lock);
>
> - /* init irq workqueue before request_irq */
> - INIT_WORK(&twl->irq_work, twl4030_usb_irq_work);
> + twl4030_usb_ldo_init(twl);
> + otg_set_transceiver(&twl->otg);
> +
> + platform_set_drvdata(pdev, twl);
> + if (device_create_file(&pdev->dev, &dev_attr_vbus))
> + dev_warn(&pdev->dev, "could not create sysfs file\n");
>
> + /* Our job is to use irqs and status from the power module
> + * to keep the transceiver disabled when nothing's connected.
> + *
> + * FIXME we actually shouldn't start enabling it until the
> + * USB controller drivers have said they're ready, by calling
> + * set_host() and/or set_peripheral() ... OTG_capable boards
> + * need both handles, otherwise just one suffices.
> + */
> twl->irq_enabled = true;
> - status = request_irq(twl->irq, twl4030_usb_irq, 0, "twl4030_usb", twl);
> + status = request_irq(twl->irq, twl4030_usb_irq,
> + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
> + "twl4030_usb", twl);
> if (status < 0) {
> dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
> twl->irq, status);
> @@ -690,25 +698,17 @@ static int __init twl4030_usb_probe(stru
> return status;
> }
>
> - twl4030_usb_ldo_init(twl);
> - twl4030_phy_power(twl, 1);
> - twl4030_i2c_access(twl, 1);
> - twl4030_usb_set_mode(twl, twl->usb_mode);
> -
> - twl->asleep = 0;
> -
> - if (twl->usb_mode == T2_USB_MODE_ULPI) {
> - twl4030_i2c_access(twl, 0);
> - twl4030_phy_suspend(twl, 0);
> - }
> + /* The IRQ handler just handles changes from the previous states
> + * of the ID and VBUS pins ... in probe() we must initialize that
> + * previous state. The easy way: fake an IRQ.
> + *
> + * REVISIT: a real IRQ might have happened already, if PREEMPT is
> + * enabled. Else the IRQ may not yet be configured or enabled,
> + * because of scheduling delays.
> + */
> + twl4030_usb_irq(twl->irq, twl);
>
> - otg_set_transceiver(&twl->otg);
> - platform_set_drvdata(pdev, twl);
> dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
> -
> - if (device_create_file(&pdev->dev, &dev_attr_vbus))
> - dev_warn(&pdev->dev, "could not create sysfs file\n");
> -
> return 0;
> }
>
> @@ -717,7 +717,6 @@ static int __exit twl4030_usb_remove(str
> struct twl4030_usb *twl = platform_get_drvdata(pdev);
> int val;
>
> - usb_irq_disable(twl);
> free_irq(twl->irq, twl);
> device_remove_file(twl->dev, &dev_attr_vbus);
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
