From: Leed Aguilar <[EMAIL PROTECTED]>
This patch sets the proper padconfig value for wvga spi chip select.
Also ensures that dvi output is disable.
LCD data lines has been changed to 24 for Zoom2
Signed-off-by: Leed Aguilar <[EMAIL PROTECTED]>
---
arch/arm/mach-omap2/mux.c | 15 ++++++++++++---
arch/arm/plat-omap/display.c | 4 ++--
arch/arm/plat-omap/include/mach/mux.h | 8 ++++++++
drivers/video/omap/omap_disp_out.c | 25 +++++++++++++++++--------
4 files changed, 39 insertions(+), 13 deletions(-)
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 0e650a4..cd6de1d 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -25,10 +25,11 @@
*/
#include <linux/module.h>
#include <linux/init.h>
-#include <asm/system.h>
#include <linux/io.h>
#include <linux/spinlock.h>
+#include <asm/system.h>
+
#include <mach/control.h>
#include <mach/mux.h>
@@ -450,7 +451,7 @@ MUX_CFG_34XX("AD2_3430_USB3FS_PHY_MM3_TXDAT", 0x188,
MUX_CFG_34XX("AC1_3430_USB3FS_PHY_MM3_TXEN_N", 0x18a,
OMAP34XX_MUX_MODE6 | OMAP34XX_PIN_OUTPUT)
- /* UART3 */
+/* UART3 */
MUX_CFG_34XX("R21_3430_UART3_CTS_RCTX", 0x19a,
OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLDOWN)
MUX_CFG_34XX("T21_3430_UART3_RTS_SD", 0x19c,
@@ -460,11 +461,15 @@ MUX_CFG_34XX("U21_3430_UART3_RX_IRRX", 0x19e,
MUX_CFG_34XX("V21_3430_UART3_TX_IRTX", 0x1a0,
OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLDOWN)
- /* GPIO */
+/* GPIO */
MUX_CFG_34XX("T21_3430_GPIO164", 0x19c,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLDOWN)
MUX_CFG_34XX("V21_3430_GPIO166", 0x1a0,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLDOWN)
+MUX_CFG_34XX("AF21_3430_GPIO8", 0xa16,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("B23_3430_GPIO167", 0x130,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
/* 34XX GPIO - bidirectional, unless the name has an "_OUT" suffix.
* No internal pullup/pulldown without "_UP" or "_DOWN" suffix.
@@ -473,6 +478,10 @@ MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+
+/* McSPI */
+MUX_CFG_34XX("AB1_3430_McSPI1_CS2", 0x1d2,
+ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLDOWN)
};
#define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)
diff --git a/arch/arm/plat-omap/display.c b/arch/arm/plat-omap/display.c
index 9ec7ff2..2fca7a9 100644
--- a/arch/arm/plat-omap/display.c
+++ b/arch/arm/plat-omap/display.c
@@ -1975,10 +1975,10 @@ omap2_disp_config_lcd(u32 clkdiv, u32 hbp, u32 hfp, u32
hsw,
#endif
dispc_reg_out(DISPC_DIVISOR, divisor);
control = dispc_reg_in(DISPC_CONTROL);
-#ifdef CONFIG_FB_OMAP_720P_STREAMING
+#if defined(CONFIG_FB_OMAP_720P_STREAMING) || defined(CONFIG_MACH_OMAP_ZOOM2)
control |= DISPC_CONTROL_TFTDATALINES_OALSB24B;
#else
-#if defined(CONFIG_MACH_OMAP_LDP) || defined(CONFIG_MACH_OMAP_ZOOM2)
+#ifdef CONFIG_MACH_OMAP_LDP
control |= DISPC_CONTROL_TFTDATALINES_OALSB18B;
#else
control |= DISPC_CONTROL_TFTDATALINES_OALSB16B;
diff --git a/arch/arm/plat-omap/include/mach/mux.h
b/arch/arm/plat-omap/include/mach/mux.h
index 0447a78..4055763 100644
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -785,8 +785,13 @@ enum omap34xx_index {
T21_3430_UART3_RTS_SD,
U21_3430_UART3_RX_IRRX,
V21_3430_UART3_TX_IRTX,
+
+ /* GPIO */
T21_3430_GPIO164,
V21_3430_GPIO166,
+ AF21_3430_GPIO8,
+ B23_3430_GPIO167,
+
/* 34xx GPIO
* - normally these are bidirectional, no internal pullup/pulldown
* - "_UP" suffix (GPIO3_UP) if internal pullup is configured
@@ -795,6 +800,9 @@ enum omap34xx_index {
*/
AH8_34XX_GPIO29,
J25_34XX_GPIO170,
+
+ /* McSPI */
+ AB1_3430_McSPI1_CS2,
};
struct omap_mux_cfg {
diff --git a/drivers/video/omap/omap_disp_out.c
b/drivers/video/omap/omap_disp_out.c
index 62bf126..4dc818e 100755
--- a/drivers/video/omap/omap_disp_out.c
+++ b/drivers/video/omap/omap_disp_out.c
@@ -30,25 +30,29 @@
#include <linux/fb.h>
#include <linux/delay.h>
#include <linux/device.h>
-#include <mach/hardware.h>
+#include <linux/delay.h>
+#include <linux/workqueue.h>
+#include <linux/platform_device.h>
+
#include <asm/uaccess.h>
#include <asm/delay.h>
-#include <linux/delay.h>
-#include <mach/display.h>
+
#include <mach/gpio.h>
#include <mach/clock.h>
+#include <mach/hardware.h>
+#include <mach/mux.h>
+#include <mach/power_companion.h>
+#include <mach/resource.h>
+#include <mach/display.h>
+
#if defined(CONFIG_MACH_OMAP_2430SDP) || defined (CONFIG_MACH_OMAP_3430SDP) ||\
defined(CONFIG_MACH_OMAP_LDP) || defined(CONFIG_MACH_OMAP_ZOOM2)
#include <linux/i2c/twl4030.h>
#endif
-#include <linux/workqueue.h>
-#include <mach/power_companion.h>
-#include <mach/resource.h>
#ifdef CONFIG_PM
#include <linux/notifier.h>
#include <linux/pm.h>
#endif
-#include <linux/platform_device.h>
#ifdef CONFIG_FB_OMAP_LCD_WVGA
#include <linux/spi/spi.h>
#endif
@@ -129,7 +133,7 @@
#define LCD_PANEL_RESET_GPIO 55
#define LCD_PANEL_QVGA_GPIO 56
#define LCD_PANEL_BACKLIGHT_GPIO (7 + OMAP_MAX_GPIO_LINES)
-#define DVI_OUTPUT_GPIO 8
+#define DVI_OUTPUT_GPIO 8
#define DVI_POWER_ON_GPIO 167
#elif defined(CONFIG_OMAP3430_ES2)
#define LCD_PANEL_ENABLE_GPIO 5
@@ -666,6 +670,7 @@ int initialize_nec_wvgalcd(void)
spi_wvgalcd_send(157, 0x00); /* R157 = 00h */
udelay(20);
spi_wvgalcd_send(2, 0x00); /* R2 = 00h */
+
return 0;
}
#endif
@@ -922,10 +927,14 @@ lcd_probe(struct platform_device *odev)
#ifdef CONFIG_FB_OMAP_LCD_WVGA
static int wvgalcd_probe(struct spi_device *spi)
{
+ omap_cfg_reg(AF21_3430_GPIO8);
+ omap_cfg_reg(B23_3430_GPIO167);
+ omap_cfg_reg(AB1_3430_McSPI1_CS2);
wvgalcd_spi = spi;
wvgalcd_spi->mode = SPI_MODE_0;
wvgalcd_spi->bits_per_word = 32;
spi_setup(wvgalcd_spi);
+
return omap_lcd_init(0);
}
#endif
--
1.6.0
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
