OmniVision ov3640 smart sensor driver (3MP) is not supported
on ZOOM2 board.
Signed-off-by: Leed Aguilar <[EMAIL PROTECTED]>
Ack-by: Dominic Curran <[EMAIL PROTECTED]>
---
arch/arm/mach-omap2/board-zoom2.c | 213 +------------------------------------
1 files changed, 1 insertions(+), 212 deletions(-)
diff --git a/arch/arm/mach-omap2/board-zoom2.c
b/arch/arm/mach-omap2/board-zoom2.c
index 6bbf6cc..c823750 100755
--- a/arch/arm/mach-omap2/board-zoom2.c
+++ b/arch/arm/mach-omap2/board-zoom2.c
@@ -47,28 +47,6 @@
#include <mach/prcm_34xx.h>
#endif
-#ifdef CONFIG_VIDEO_OMAP3
-#include <media/v4l2-int-device.h>
-#include <../drivers/media/video/omap34xxcam.h>
-#include <../drivers/media/video/isp/ispreg.h>
-#if defined(CONFIG_VIDEO_OV3640) || defined(CONFIG_VIDEO_OV3640_MODULE)
-#include <../drivers/media/video/ov3640.h>
-#include <../drivers/media/video/isp/ispcsi2.h>
-static struct omap34xxcam_hw_config *hwc;
-#define OV3640_CSI2_CLOCK_POLARITY 0 /* +/- pin order */
-#define OV3640_CSI2_DATA0_POLARITY 0 /* +/- pin order */
-#define OV3640_CSI2_DATA1_POLARITY 0 /* +/- pin order */
-#define OV3640_CSI2_CLOCK_LANE 1 /* Clock lane position: 1 */
-#define OV3640_CSI2_DATA0_LANE 2 /* Data0 lane position: 2 */
-#define OV3640_CSI2_DATA1_LANE 3 /* Data1 lane position: 3 */
-#define OV3640_CSI2_PHY_THS_TERM 4
-#define OV3640_CSI2_PHY_THS_SETTLE 14
-#define OV3640_CSI2_PHY_TCLK_TERM 0
-#define OV3640_CSI2_PHY_TCLK_MISS 1
-#define OV3640_CSI2_PHY_TCLK_SETTLE 14
-#endif
-#endif
-
#define SDP3430_SMC91X_CS 3
#define ENABLE_VAUX1_DEDICATED 0x03
#define ENABLE_VAUX1_DEV_GRP 0x20
@@ -311,7 +289,6 @@ static struct twl4030_keypad_data ldp_kp_twl4030_data = {
.rep = 1,
.irq = TWL4030_MODIRQ_KEYPAD,
};
-static int ts_gpio;
static int __init msecure_init(void)
{
@@ -484,182 +461,6 @@ static struct twl4030_platform_data ldp_twldata = {
.keypad = &ldp_kp_twl4030_data,
};
-#if defined(CONFIG_VIDEO_OV3640) || defined(CONFIG_VIDEO_OV3640_MODULE)
-
-static struct omap34xxcam_sensor_config ov3640_hwc = {
- .sensor_isp = 0,
-#if defined(CONFIG_VIDEO_OV3640_CSI2)
- .xclk = OMAP34XXCAM_XCLK_B,
-#else
- .xclk = OMAP34XXCAM_XCLK_A,
-#endif
- .capture_mem = 2592 * 1944 * 2 * 2,
-};
-
-static struct isp_interface_config ov3640_if_config = {
- .ccdc_par_ser = ISP_CSIA,
- .dataline_shift = 0x0,
- .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE,
- .vdint0_timing = 0x0,
- .vdint1_timing = 0x0,
- .strobe = 0x0,
- .prestrobe = 0x0,
- .shutter = 0x0,
- .prev_sph = 2,
- .prev_slv = 1,
- .wenlog = ISPCCDC_CFG_WENLOG_AND,
- .u.csi.crc = 0x0,
- .u.csi.mode = 0x0,
- .u.csi.edge = 0x0,
- .u.csi.signalling = 0x0,
- .u.csi.strobe_clock_inv = 0x0,
- .u.csi.vs_edge = 0x0,
- .u.csi.channel = 0x1,
- .u.csi.vpclk = 0x1,
- .u.csi.data_start = 0x0,
- .u.csi.data_size = 0x0,
- .u.csi.format = V4L2_PIX_FMT_SGRBG10,
-};
-
-static int ov3640_sensor_set_prv_data(void *priv)
-{
-
- hwc = priv;
- hwc->u.sensor.xclk = ov3640_hwc.xclk;
- hwc->u.sensor.sensor_isp = ov3640_hwc.sensor_isp;
- hwc->dev_index = 1;
- hwc->dev_minor = 4;
- hwc->dev_type = OMAP34XXCAM_SLAVE_SENSOR;
- hwc->interface_type = ISP_CSIA;
-
-#if defined(CONFIG_VIDEO_OV3640_CSI2)
- hwc->csi2.hw_csi2.lanes.clock.polarity = OV3640_CSI2_CLOCK_POLARITY;
- hwc->csi2.hw_csi2.lanes.clock.position = OV3640_CSI2_CLOCK_LANE;
- hwc->csi2.hw_csi2.lanes.data[0].polarity = OV3640_CSI2_DATA0_POLARITY;
- hwc->csi2.hw_csi2.lanes.data[0].position = OV3640_CSI2_DATA0_LANE;
- hwc->csi2.hw_csi2.lanes.data[1].polarity = OV3640_CSI2_DATA1_POLARITY;
- hwc->csi2.hw_csi2.lanes.data[1].position = OV3640_CSI2_DATA1_LANE;
- hwc->csi2.hw_csi2.phy.ths_term = OV3640_CSI2_PHY_THS_TERM;
- hwc->csi2.hw_csi2.phy.ths_settle = OV3640_CSI2_PHY_THS_SETTLE;
- hwc->csi2.hw_csi2.phy.tclk_term = OV3640_CSI2_PHY_TCLK_TERM;
- hwc->csi2.hw_csi2.phy.tclk_miss = OV3640_CSI2_PHY_TCLK_MISS;
- hwc->csi2.hw_csi2.phy.tclk_settle = OV3640_CSI2_PHY_TCLK_SETTLE;
-#endif
-
- return 0;
-}
-
-static int ov3640_sensor_power_set(enum v4l2_power power)
-{
- struct isp_csi2_lanes_cfg lanecfg;
- struct isp_csi2_phy_cfg phyconfig;
- static enum v4l2_power previous_power = V4L2_POWER_OFF;
- switch (power) {
- case V4L2_POWER_ON:
- printk(KERN_DEBUG "ov3640_sensor_power_set(ON)\n");
- if (previous_power == V4L2_POWER_OFF)
- isp_csi2_reset();
- lanecfg.clk.pol = OV3640_CSI2_CLOCK_POLARITY;
- lanecfg.clk.pos = OV3640_CSI2_CLOCK_LANE;
- lanecfg.data[0].pol = OV3640_CSI2_DATA0_POLARITY;
- lanecfg.data[0].pos = OV3640_CSI2_DATA0_LANE;
- lanecfg.data[1].pol = OV3640_CSI2_DATA1_POLARITY;
- lanecfg.data[1].pos = OV3640_CSI2_DATA1_LANE;
- lanecfg.data[2].pol = 0;
- lanecfg.data[2].pos = 0;
- lanecfg.data[3].pol = 0;
- lanecfg.data[3].pos = 0;
- isp_csi2_complexio_lanes_config(&lanecfg);
- isp_csi2_complexio_lanes_update(true);
-
- phyconfig.ths_term = OV3640_CSI2_PHY_THS_TERM;
- phyconfig.ths_settle = OV3640_CSI2_PHY_THS_SETTLE;
- phyconfig.tclk_term = OV3640_CSI2_PHY_TCLK_TERM;
- phyconfig.tclk_miss = OV3640_CSI2_PHY_TCLK_MISS;
- phyconfig.tclk_settle = OV3640_CSI2_PHY_TCLK_SETTLE;
- isp_csi2_phy_config(&phyconfig);
- isp_csi2_phy_update(true);
-
- isp_configure_interface(&ov3640_if_config);
-
- if (previous_power == V4L2_POWER_OFF) {
-#ifdef CONFIG_TWL4030_CORE
- /* turn on analog power */
-#if defined(CONFIG_VIDEO_OV3640_CSI2)
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_1_8_V, TWL4030_VAUX4_DEDICATED);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_DEV_GRP_P1, TWL4030_VAUX4_DEV_GRP);
-#else
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_2_8_V, TWL4030_VAUX2_DEDICATED);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_DEV_GRP_P1, TWL4030_VAUX2_DEV_GRP);
-#endif
- udelay(100);
-#else
-#error "no power companion board defined!"
-#endif
- /* Request and configure gpio pins */
- if (omap_request_gpio(OV3640_RESET_GPIO) != 0) {
- printk(KERN_ERR "Could not request GPIO %d",
- OV3640_RESET_GPIO);
- return -EIO;
- }
- if (omap_request_gpio(OV3640_STANDBY_GPIO) != 0) {
- printk(KERN_ERR "Could not request GPIO %d",
- OV3640_STANDBY_GPIO);
- return -EIO;
- }
- /* set to output mode */
- omap_set_gpio_direction(OV3640_RESET_GPIO, 0);
- omap_set_gpio_direction(OV3640_STANDBY_GPIO, 0);
-
- /* Turn ON Omnivision sensor */
- omap_set_gpio_dataout(OV3640_RESET_GPIO, 1);
- omap_set_gpio_dataout(OV3640_STANDBY_GPIO, 0);
- udelay(100);
-
- /* RESET Omnivision sensor */
- omap_set_gpio_dataout(OV3640_RESET_GPIO, 0);
- udelay(100);
- omap_set_gpio_dataout(OV3640_RESET_GPIO, 1);
- }
- break;
- case V4L2_POWER_OFF:
- printk(KERN_DEBUG "ov3640_sensor_power_set(OFF)\n");
- /* Power Down Sequence */
-
-#ifdef CONFIG_TWL4030_CORE
-#if defined(CONFIG_VIDEO_OV3640_CSI2)
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_DEV_GRP_NONE, TWL4030_VAUX4_DEV_GRP);
-#else
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
- VAUX_DEV_GRP_NONE, TWL4030_VAUX2_DEV_GRP);
-#endif
-#else
-#error "no power companion board defined!"
-#endif
- omap_free_gpio(OV3640_RESET_GPIO);
- omap_free_gpio(OV3640_STANDBY_GPIO);
- break;
- case V4L2_POWER_STANDBY:
- printk(KERN_DEBUG "ov3640_sensor_power_set(STANDBY)\n");
- break;
- }
- previous_power = power;
- return 0;
-}
-
-static struct ov3640_platform_data sdp3430_ov3640_platform_data = {
- .power_set = ov3640_sensor_power_set,
- .priv_data_set = ov3640_sensor_set_prv_data,
- .default_regs = ov3640_common[0],
-};
-
-#endif
-
static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
@@ -669,21 +470,11 @@ static struct i2c_board_info __initdata
ldp_i2c_boardinfo[] = {
},
};
-static struct i2c_board_info __initdata ldp_i2c_boardinfo_2[] = {
-#if defined(CONFIG_VIDEO_OV3640) || defined(CONFIG_VIDEO_OV3640_MODULE)
- {
- I2C_BOARD_INFO("ov3640", OV3640_I2C_ADDR),
- .platform_data = &sdp3430_ov3640_platform_data,
- },
-#endif
-};
-
static int __init omap_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, ldp_i2c_boardinfo,
ARRAY_SIZE(ldp_i2c_boardinfo));
- omap_register_i2c_bus(2, 100, ldp_i2c_boardinfo_2,
- ARRAY_SIZE(ldp_i2c_boardinfo_2));
+ omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
@@ -694,8 +485,6 @@ static void __init omap_ldp_init(void)
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
omap_board_config = ldp_config;
omap_board_config_size = ARRAY_SIZE(ldp_config);
- ts_gpio = 54;
- ldp_spi_board_info[0].irq = OMAP_GPIO_IRQ(ts_gpio);
spi_register_board_info(ldp_spi_board_info,
ARRAY_SIZE(ldp_spi_board_info));
--
1.6.0
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
