From: Vaibhav Hiremath <[email protected]>
This is first version of OMAP3EVM Mulit-Media Daughter
Card support.
Tested:
- TVP5146 (BT656) decoder interface on top of
Sergio's ISP-Camera patches.
- Loopback application, capturing image through TVP5146
and displaying it onto the TV/LCD on top of Hardik's
V4L2 driver.
- Basic functionality of HSUSB Transceiver USB-83320
-
TODO:
- Camera sensor support
- Driver header file inclusion (dependency on ISP-Camera patches)
- Some more clean-up may required.
Signed-off-by: Brijesh Jadav <[email protected]>
Signed-off-by: Hardik Shah <[email protected]>
Signed-off-by: Manjunath Hadli <[email protected]>
Signed-off-by: R Sivaraj <[email protected]>
Signed-off-by: Vaibhav Hiremath <[email protected]>
---
arch/arm/mach-omap2/Kconfig | 4 +
arch/arm/mach-omap2/Makefile | 1 +
arch/arm/mach-omap2/board-omap3evm-dc.c | 417 +++++++++++++++++++++++++++++++
arch/arm/mach-omap2/board-omap3evm-dc.h | 43 ++++
arch/arm/mach-omap2/mux.c | 7 +
arch/arm/plat-omap/include/mach/mux.h | 4 +
6 files changed, 476 insertions(+), 0 deletions(-)
mode change 100644 => 100755 arch/arm/mach-omap2/Kconfig
mode change 100644 => 100755 arch/arm/mach-omap2/Makefile
create mode 100755 arch/arm/mach-omap2/board-omap3evm-dc.c
create mode 100755 arch/arm/mach-omap2/board-omap3evm-dc.h
mode change 100644 => 100755 arch/arm/mach-omap2/mux.c
mode change 100644 => 100755 arch/arm/plat-omap/include/mach/mux.h
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
old mode 100644
new mode 100755
index ca24a7a..094c97f
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -121,6 +121,10 @@ config MACH_OMAP3EVM
bool "OMAP 3530 EVM board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
+config MACH_OMAP3EVM_DC
+ bool "OMAP 3530 EVM daughter card board"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX && MACH_OMAP3EVM
+
config MACH_OMAP3_BEAGLE
bool "OMAP3 BEAGLE board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
old mode 100644
new mode 100755
index 3897347..16fa35a
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o \
usb-musb.o usb-ehci.o \
board-omap3evm-flash.o \
twl4030-generic-scripts.o
+obj-$(CONFIG_MACH_OMAP3EVM_DC) += board-omap3evm-dc.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \
usb-musb.o usb-ehci.o \
mmc-twl4030.o \
diff --git a/arch/arm/mach-omap2/board-omap3evm-dc.c
b/arch/arm/mach-omap2/board-omap3evm-dc.c
new file mode 100755
index 0000000..233c219
--- /dev/null
+++ b/arch/arm/mach-omap2/board-omap3evm-dc.c
@@ -0,0 +1,417 @@
+/*
+ * arch/arm/mach-omap2/board-omap3evm-dc.c
+ *
+ * Driver for OMAP3 EVM Daughter Card
+ *
+ * Copyright (C) 2008 Texas Instruments Inc
+ * Author: Vaibhav Hiremath <[email protected]>
+ *
+ * Contributors:
+ * Anuj Aggarwal <[email protected]>
+ * Sivaraj R <[email protected]>
+ *
+ * This package is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel_stat.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <mach/io.h>
+#include <mach/mux.h>
+
+#if defined(CONFIG_VIDEO_TVP514X) || defined(CONFIG_VIDEO_TVP514X_MODULE)
+#include <linux/videodev2.h>
+#include <media/v4l2-int-device.h>
+#include <media/tvp514x.h>
+/* include V4L2 camera driver related header file */
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+#include <../drivers/media/video/omap34xxcam.h>
+#include <../drivers/media/video/isp/ispreg.h>
+#endif /* #ifdef CONFIG_VIDEO_OMAP3 */
+#endif /* #ifdef CONFIG_VIDEO_TVP514X*/
+
+#include "board-omap3evm-dc.h"
+
+#define MODULE_NAME "omap3evmdc"
+
+#ifdef DEBUG
+#define dprintk(fmt, args...) printk(KERN_ERR MODULE_NAME ": " fmt, ## args)
+#else
+#define dprintk(fmt, args...)
+#endif /* #ifdef DEBUG */
+
+/* Macro Definitions */
+
+/* System control module register offsets */
+#define REG_CONTROL_PADCONF_I2C2_SDA (0x480021C0u)
+#define REG_CONTROL_PADCONF_I2C3_SDA (0x480021C4u)
+
+#define PADCONF_I2C3_SCL_MASK (0xFFFF0000u)
+#define PADCONF_I2C3_SDA_MASK (0x0000FFFFu)
+
+/* mux mode 0 (enable I2C3 SCL), pull-up enable, input enable */
+#define PADCONF_I2C3_SCL_DEF (0x01180000u)
+/* mux mode 0 (enable I2C3 SDA), pull-up enable, input enable */
+#define PADCONF_I2C3_SDA_DEF (0x00000118u)
+
+/* GPIO pins */
+#define GPIO134_SEL_Y (134)
+#define GPIO54_SEL_EXP_CAM (54)
+#define GPIO136_SEL_CAM (136)
+
+/* board internal information (BEGIN) */
+
+/* I2C bus to which all I2C slave devices are attached */
+#define BOARD_I2C_BUSNUM (3)
+
+/* I2C address of chips present in board */
+#define TVP5146_I2C_ADDR (0x5D)
+
+/* Register offsets */
+#define REG_BUS_CTRL1 (0x00000180u)
+#define REG_BUS_CTRL2 (0x000001C0u)
+
+/* Bit defines for Bus Control 1 register */
+#define TVP5146_EN_SHIFT (0x0000u)
+#define TVP5146_EN_MASK (1u << TVP5146_EN_SHIFT)
+
+#define CAMERA_SENSOR_EN_SHIFT (0x0008u)
+#define CAMERA_SENSOR_EN_MASK (1u << CAMERA_SENSOR_EN_SHIFT)
+
+/* default value for bus control registers */
+#define BUS_CONTROL1_DEF (0x0141u) /* Disable all mux */
+#define BUS_CONTROL2_DEF (0x010Au) /* Disable all mux */
+
+#if defined(CONFIG_VIDEO_TVP514X) || defined(CONFIG_VIDEO_TVP514X_MODULE)
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+static struct omap34xxcam_hw_config decoder_hwc = {
+ .dev_index = 0,
+ .dev_minor = 0,
+ .dev_type = OMAP34XXCAM_SLAVE_SENSOR,
+ .u.sensor.xclk = OMAP34XXCAM_XCLK_NONE,
+ .u.sensor.sensor_isp = 1,
+};
+
+static struct isp_interface_config tvp5146_if_config = {
+ .ccdc_par_ser = ISP_PARLL_YUV_BT,
+ .dataline_shift = 0x1,
+ .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE,
+ .vdint0_timing = 0x0,
+ .vdint1_timing = 0x0,
+ .strobe = 0x0,
+ .prestrobe = 0x0,
+ .shutter = 0x0,
+ .u.par.par_bridge = 0x0,
+ .u.par.par_clk_pol = 0x0,
+};
+#endif
+
+static struct v4l2_ifparm ifparm = {
+ .if_type = V4L2_IF_TYPE_BT656,
+ .u = {
+ .bt656 = {
+ .frame_start_on_rising_vs = 1,
+ .bt_sync_correct = 0,
+ .swap = 0,
+ .latch_clk_inv = 0,
+ .nobt_hs_inv = 0, /* active high */
+ .nobt_vs_inv = 0, /* active high */
+ .mode = V4L2_IF_TYPE_BT656_MODE_BT_8BIT,
+ .clock_min = TVP514X_XCLK_BT656,
+ .clock_max = TVP514X_XCLK_BT656,
+ },
+ },
+};
+
+/**
+ * @brief tvp5146_ifparm - Returns the TVP5146 decoder interface parameters
+ *
+ * @param p - pointer to v4l2_ifparm structure
+ *
+ * @return result of operation - 0 is success
+ */
+static int tvp5146_ifparm(struct v4l2_ifparm *p)
+{
+ if (p == NULL)
+ return -EINVAL;
+
+ *p = ifparm;
+ return 0;
+}
+
+/**
+ * @brief tvp5146_set_prv_data - Returns tvp5146 omap34xx driver private data
+ *
+ * @param priv - pointer to omap34xxcam_hw_config structure
+ *
+ * @return result of operation - 0 is success
+ */
+static int tvp5146_set_prv_data(void *priv)
+{
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+ struct omap34xxcam_hw_config *hwc = priv;
+
+ if (priv == NULL)
+ return -EINVAL;
+
+ hwc->u.sensor.sensor_isp = decoder_hwc.u.sensor.sensor_isp;
+ hwc->u.sensor.xclk = decoder_hwc.u.sensor.xclk;
+ hwc->dev_index = decoder_hwc.dev_index;
+ hwc->dev_minor = decoder_hwc.dev_minor;
+ hwc->dev_type = decoder_hwc.dev_type;
+ return 0;
+#else
+ return -EINVAL;
+#endif
+}
+
+/**
+ * @brief omap3evmdc_set_mux - Sets mux to enable/disable signal routing to
+ * different peripherals present in board
+ * IMPORTANT - This function will take care of writing appropriate values for
+ * active low signals as well
+ *
+ * @param mux_id - enum, mux id to enable/disable
+ * @param value - enum, ENABLE_MUX for enabling and DISABLE_MUX for disabling
+ *
+ * @return result of operation - 0 is success
+ */
+static int omap3evmdc_set_mux(enum omap3evmdc_mux mux_id, enum config_mux
value)
+{
+ int err = 0;
+
+ if (unlikely(mux_id >= NUM_MUX)) {
+ dprintk("Invalid mux id\n");
+ return -EPERM;
+ }
+
+
+ switch (mux_id) {
+ case MUX_TVP5146:
+ /* active low signal. set 0 to enable, 1 to disable */
+ if (ENABLE_MUX == value) {
+ /* pull down the GPIO GPIO134 = 0 */
+ gpio_set_value(GPIO134_SEL_Y, 0);
+ /* pull up the GPIO GPIO54 = 1 */
+ gpio_set_value(GPIO54_SEL_EXP_CAM, 1);
+ /* pull up the GPIO GPIO136 = 1 */
+ gpio_set_value(GPIO136_SEL_CAM, 1);
+ } else
+ /* pull up the GPIO GPIO134 = 0 */
+ gpio_set_value(GPIO134_SEL_Y, 1);
+
+ break;
+
+ case MUX_CAMERA_SENSOR:
+ /* active low signal. set 0 to enable, 1 to disable */
+ if (ENABLE_MUX == value) {
+ /* pull up the GPIO GPIO134 = 0 */
+ gpio_set_value(GPIO134_SEL_Y, 1);
+ /* pull up the GPIO GPIO54 = 1 */
+ gpio_set_value(GPIO54_SEL_EXP_CAM, 1);
+ /* pull down the GPIO GPIO136 = 1 */
+ gpio_set_value(GPIO136_SEL_CAM, 0);
+ } else
+ /* pull up the GPIO GPIO136 = 1 */
+ gpio_set_value(GPIO136_SEL_CAM, 1);
+
+ break;
+
+ case MUX_EXP_CAMERA_SENSOR:
+ /* active low signal. set 0 to enable, 1 to disable */
+ if (ENABLE_MUX == value) {
+ /* pull up the GPIO GPIO134 = 1 */
+ gpio_set_value(GPIO134_SEL_Y, 1);
+ /* pull down the GPIO GPIO54 = 1 */
+ gpio_set_value(GPIO54_SEL_EXP_CAM, 0);
+ /* pull up the GPIO GPIO136 = 1 */
+ gpio_set_value(GPIO136_SEL_CAM, 1);
+ } else
+ /* pull up the GPIO GPIO54 = 1 */
+ gpio_set_value(GPIO54_SEL_EXP_CAM, 1);
+
+ break;
+
+ case NUM_MUX:
+ default:
+ dprintk("Invalid mux id\n");
+ err = -EPERM;
+ }
+
+ return err;
+}
+/**
+ * @brief tvp5146_power_set - Power-on or power-off TVP5146 device
+ *
+ * @param power - enum, Power on/off, resume/standby
+ *
+ * @return result of operation - 0 is success
+ */
+static int tvp5146_power_set(enum v4l2_power power)
+{
+ switch (power) {
+ case V4L2_POWER_OFF:
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+ if (isp_free_interface(ISP_PARLL_YUV_BT))
+ return -ENODEV;
+#endif
+ /* Disable mux for TVP5146 decoder data path */
+ if (omap3evmdc_set_mux(MUX_TVP5146, DISABLE_MUX))
+ return -ENODEV;
+ break;
+
+ case V4L2_POWER_STANDBY:
+ break;
+
+ case V4L2_POWER_ON:
+ /* Enable mux for TVP5146 decoder data path */
+ if (omap3evmdc_set_mux(MUX_TVP5146, ENABLE_MUX))
+ return -ENODEV;
+
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+ if (isp_request_interface(ISP_PARLL_YUV_BT))
+ return -ENODEV;
+
+ isp_configure_interface(&tvp5146_if_config);
+#endif
+ break;
+
+ default:
+ return -ENODEV;
+ break;
+ }
+ return 0;
+}
+
+static struct tvp514x_platform_data tvp5146_pdata = {
+ .master = "omap34xxcam",
+ .power_set = tvp5146_power_set,
+ .priv_data_set = tvp5146_set_prv_data,
+ .ifparm = tvp5146_ifparm,
+
+ /* Some interface dependent params */
+ .clk_polarity = 0, /* data clocked out on falling edge */
+ .hs_polarity = 1, /* 0 - Active low, 1- Active high */
+ .vs_polarity = 1, /* 0 - Active low, 1- Active high */
+};
+
+static struct i2c_board_info __initdata tvp5146_i2c_board_info = {
+ I2C_BOARD_INFO("tvp5146m2", TVP5146_I2C_ADDR),
+ .platform_data = &tvp5146_pdata,
+};
+
+#endif /* #ifdef CONFIG_VIDEO_TVP514X */
+
+/**
+ * @brief omap3evmdc_mdc_config - GPIO configuration for
+ * GPIO 134, 54 and 136
+ *
+ * @return result of operation - 0 is success
+ */
+static int omap3evmdc_mdc_config(void)
+{
+ /* Setting the MUX configuration */
+ omap_cfg_reg(GPIO134_VDIN_SEL_Y);
+ omap_cfg_reg(GPIO54_VDIN_SEL_EXP_CAM);
+ omap_cfg_reg(GPIO136_VDIN_SEL_CAM);
+
+ if (gpio_request(GPIO134_SEL_Y, "GPIO134_SEL_Y") < 0) {
+ dprintk("can't get GPIO 134\n");
+ return -EINVAL;
+ }
+
+ if (gpio_request(GPIO54_SEL_EXP_CAM, "GPIO54_SEL_EXP_CAM") < 0) {
+ dprintk("can't get GPIO 54\n");
+ return -EINVAL;
+ }
+
+ if (gpio_request(GPIO136_SEL_CAM, "GPIO136_SEL_CAM") < 0) {
+ dprintk("can't get GPIO 136\n");
+ return -EINVAL;
+ }
+
+ /* Make GPIO as output */
+ gpio_direction_output(GPIO134_SEL_Y, 0);
+ /* Make GPIO as output */
+ gpio_direction_output(GPIO54_SEL_EXP_CAM, 0);
+ /* Make GPIO as output */
+ gpio_direction_output(GPIO136_SEL_CAM, 0);
+
+ return 0;
+}
+
+/**
+ * @brief omap3evmdc_init - module init function. Should be called before any
+ * client driver init call
+ *
+ * @return result of operation - 0 is success
+ */
+static int __init omap3evmdc_init(void)
+{
+ int err;
+
+ /*
+ * I2C3 SCL pin mux settings - mux mode 0, pull-up enable, input enable
+ * Uses the MSB 16-bit of this register, retain the LSB 16-bit.
+ * This pin is shared with gpio_184 (mux mode 4)
+ */
+ omap_writel(((omap_readl(REG_CONTROL_PADCONF_I2C2_SDA) &
+ ~PADCONF_I2C3_SCL_MASK) | PADCONF_I2C3_SCL_DEF),
+ REG_CONTROL_PADCONF_I2C2_SDA);
+
+ /*
+ * I2C3 SDA pin mux settings - mux mode 0, pull-up enable, input enable
+ * Uses the LSB 16-bit of this register, retain the MSB 16-bit.
+ * This pin is shared with gpio_185 (mux mode 4)
+ */
+ omap_writel(((omap_readl(REG_CONTROL_PADCONF_I2C3_SDA) &
+ ~PADCONF_I2C3_SDA_MASK) | PADCONF_I2C3_SDA_DEF),
+ REG_CONTROL_PADCONF_I2C3_SDA);
+
+ err = omap3evmdc_mdc_config();
+ if (err) {
+ dprintk("MDC configuration failed \n");
+ return err;
+ }
+
+ /*
+ * Register each of the I2C devices present in the board to the I2C
+ * framework.
+ * If more I2C devices are added, then each device information should
+ * be registered with I2C using i2c_register_board_info().
+ */
+#if defined(CONFIG_VIDEO_TVP514X) || defined(CONFIG_VIDEO_TVP514X_MODULE)
+ err = i2c_register_board_info(BOARD_I2C_BUSNUM,
+ &tvp5146_i2c_board_info, 1);
+ if (err) {
+ dprintk("TVP5146 I2C Board Registration failed \n");
+ return err;
+ }
+#endif
+
+ printk(KERN_INFO MODULE_NAME ": Driver registration complete \n");
+
+ return 0;
+}
+
+arch_initcall(omap3evmdc_init);
diff --git a/arch/arm/mach-omap2/board-omap3evm-dc.h
b/arch/arm/mach-omap2/board-omap3evm-dc.h
new file mode 100755
index 0000000..5eaffc5
--- /dev/null
+++ b/arch/arm/mach-omap2/board-omap3evm-dc.h
@@ -0,0 +1,43 @@
+/*
+ * arch/arm/mach-omap2/board-omap3evm-dc.h
+ *
+ * Copyright (C) 2008 Texas Instruments Inc
+ * Author: Vaibhav Hiremath <[email protected]>
+ *
+ * Contributors:
+ * Anuj Aggarwal <[email protected]>
+ * Sivaraj R <[email protected]>
+ *
+ * This package is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __BOARD_OMAP3EVM_DC_H_
+#define __BOARD_OMAP3EVM_DC_H_
+
+/* mux id to enable/disable signal routing to different peripherals */
+enum omap3evmdc_mux {
+ MUX_TVP5146 = 0,
+ MUX_CAMERA_SENSOR,
+ MUX_EXP_CAMERA_SENSOR,
+ NUM_MUX
+};
+
+/* enum to enable or disable mux */
+enum config_mux {
+ DISABLE_MUX,
+ ENABLE_MUX
+};
+
+#endif /* __BOARD_OMAP3EVM_DC_H_ */
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
old mode 100644
new mode 100755
index dacb41f..5b878b6
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -459,6 +459,13 @@ MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+
+MUX_CFG_34XX("GPIO134_VDIN_SEL_Y", 0x160,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("GPIO_54_VDIN_SEL_EXP_CAM", 0x0b4,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("GPIO136_VDIN_SEL_CAM", 0x164,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
};
#define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)
diff --git a/arch/arm/plat-omap/include/mach/mux.h
b/arch/arm/plat-omap/include/mach/mux.h
old mode 100644
new mode 100755
index f4362b8..2cd5cde
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -790,6 +790,10 @@ enum omap34xx_index {
*/
AH8_34XX_GPIO29,
J25_34XX_GPIO170,
+
+ GPIO134_VDIN_SEL_Y,
+ GPIO54_VDIN_SEL_EXP_CAM,
+ GPIO136_VDIN_SEL_CAM,
};
struct omap_mux_cfg {
--
1.5.6
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
