Felipe Balbi wrote:
> On Fri, Feb 20, 2009 at 12:05:49PM -0700, Gary Thomas wrote:
>> Felipe Balbi wrote:
>>> On Fri, Feb 20, 2009 at 11:50:44AM -0700, Gary Thomas wrote:
>>>> Felipe Balbi wrote:
>>>>> On Fri, Feb 20, 2009 at 11:15:36AM -0700, Gary Thomas wrote:
>>>>>> I have a 3530 board (similar to the OMAP3EVM) and I'm trying
>>>>>> to get the USB host working. Sadly, this is failing, but I
>>>>>> don't quite see why. From drivers/usb/host/echi-omap.c:
>>>>>> /* Wait for TLL to be Active */
>>>>>> timeout = 1000;
>>>>>> while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
>>>>>> & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
>>>>>> {
>>>>>> if (--timeout <= 0) {
>>>>>> printk(KERN_ERR "USB TLL is unavailable\n");
>>>>>> return -ENODEV;
>>>>>> }
>>>>>> cpu_relax();
>>>>>> }
>>>>>>
>>>>>> Any clues on why this might be? How do I solve it?
>>>>> could you enable CONFIG_DEBUG_LL and post the seria console output ?
>>>>>
>>>>> do you really use TLL ?? I don't really know omap3evm, but I guess it
>>>>> uses PHY mode (correct me if I'm wrong).
>>>>>
>>>> It's not that I _need_ TLL, the driver function omap_start_ehci()
>>>> tries to reset the part of the USB controller and fails. I'm just
>>>> trying to understand why this part of the code falls over.
>>> you have OMAP_EHCI_TLL_MODE set, you should probably use
>>> OMAP_EHCI_PHY_MODE instead.
>>>
>>> You can fix it via "make menuconfig"
>>>
>> I already have that; this code is still being used.
>> # CONFIG_OMAP_EHCI_TLL_MODE is not set
>> CONFIG_OMAP_EHCI_PHY_MODE=y
>>
>> This is not used in the function above at all.
>
> hmm.. true, just checked the function.
>
> Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we
> should access it when it's 0, try the following:
>
> diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
> index 1b3266c..122e95b 100644
> --- a/drivers/usb/host/ehci-omap.c
> +++ b/drivers/usb/host/ehci-omap.c
> @@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev,
> struct usb_hcd *hcd)
>
> /* Wait for TLL to be Active */
> while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
> - & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
> + & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
> cpu_relax();
>
> /* perform TLL soft reset, and wait until reset is complete */
>
> and tell us if it worked
>
Sadly, I've already tried this and things just continue to fall apart.
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010
Internal error: : 1008 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.27-omap1-svn4799-dirty14 #60)
PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
LR is at release_console_sem+0x1a8/0x1d8
Hence, my desired to figure out the TLL timeout...
--
------------------------------------------------------------
Gary Thomas | Consulting for the
MLB Associates | Embedded world
------------------------------------------------------------
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
