On Friday 20 December 2013 11:45 PM, Michael Trimarchi wrote:
Hi
On Fri, Dec 20, 2013 at 6:35 PM, Balaji T K <balaj...@ti.com> wrote:
In DT case, PBAIS registers are programmed via regulator,
use regulator APIs to control PBIAS.
Signed-off-by: Balaji T K <balaj...@ti.com>
---
drivers/mmc/host/omap_hsmmc.c | 39 +++++++++++++++++++++++++++++++++++++++
1 files changed, 39 insertions(+), 0 deletions(-)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 342be25..0a390f8 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -126,6 +126,10 @@
#define OMAP_MMC_MAX_CLOCK 52000000
#define DRIVER_NAME "omap_hsmmc"
+#define VDD_1V8 1800000 /* 180000 uV */
+#define VDD_3V0 3000000 /* 300000 uV */
+#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1)
+
/*
* One controller can have multiple slots, like on some omap boards using
* omap.c controller driver. Luckily this is not currently done on any known
@@ -164,6 +168,8 @@ struct omap_hsmmc_host {
*/
struct regulator *vcc;
struct regulator *vcc_aux;
+ struct regulator *pbias;
+ bool pbias_enabled;
int pbias_disable;
void __iomem *base;
resource_size_t mapbase;
@@ -272,6 +278,15 @@ static int omap_hsmmc_set_power(struct device *dev, int
slot, int power_on,
if (mmc_slot(host).before_set_reg)
mmc_slot(host).before_set_reg(dev, slot, power_on, vdd);
+ if (host->pbias) {
+ if (host->pbias_enabled == 1) {
+ ret = regulator_disable(host->pbias);
+ if (!ret)
+ host->pbias_enabled = 0;
you should return error?
+ }
+ regulator_set_voltage(host->pbias, VDD_3V0, VDD_3V0);
+ }
+
/*
* Assume Vcc regulator is used only to power the card ... OMAP
* VDDS is used to power the pins, optionally with a transceiver to
@@ -306,9 +321,29 @@ static int omap_hsmmc_set_power(struct device *dev, int
slot, int power_on,
}
}
+ if (host->pbias) {
+ if (vdd <= VDD_165_195)
+ ret = regulator_set_voltage(host->pbias, VDD_1V8,
+ VDD_1V8);
+ else
+ ret = regulator_set_voltage(host->pbias, VDD_3V0,
+ VDD_3V0);
+ if (ret < 0)
+ goto error_set_power;
+
+ if (host->pbias_enabled == 0) {
+ ret = regulator_enable(host->pbias);
+ if (!ret) {
+ host->pbias_enabled = 1;
+ goto error_set_power;
Is this an error condition? Do you need this flag?
Hi,
pbias_enabled flag is used to balance regulator_enable/regulator_disable,
otherwise
regulator might be kept enabled base on to use count.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
