This patch adds support for the Siemens Draco SOM (System On Module) which is used by multiple Siemens boards. Support for one is posted in this series as well, the dxr2-e.
This SOM is based on the TI AM3352 with the following configuration: - CPU: AM3352BZCEA30 - RAM: 128MB DDR3@303MHz - NAND FLASH: 256MB - RTC: disabled via hw wiring (registers not available!) Signed-off-by: Stefan Roese <[email protected]> Cc: Lukas Stockmann <[email protected]> Cc: Benoit Cousson <[email protected]> Cc: Tony Lindgren <[email protected]> --- arch/arm/boot/dts/am335x-draco.dtsi | 163 ++++++++++++++++++++++++++++++++++++ 1 file changed, 163 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-draco.dtsi diff --git a/arch/arm/boot/dts/am335x-draco.dtsi b/arch/arm/boot/dts/am335x-draco.dtsi new file mode 100644 index 0000000..88b414a --- /dev/null +++ b/arch/arm/boot/dts/am335x-draco.dtsi @@ -0,0 +1,163 @@ +/* + * Common support for Siemens Draco SOM (AM335x based) + * + * Copyright (C) 2013,2014 - Stefan Roese <[email protected]> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/ { + memory { + device_type = "memory"; + reg = <0x80000000 0x08000000>; /* 128 MB */ + }; + + am33xx_pinmux: pinmux@44e10800 { + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + nandflash_pins: nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + }; + + ocp { + uart0: serial@44e09000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; + }; + + i2c0: i2c@44e0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + eeprom: eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <64>; + }; + }; + + musb: usb@47400000 { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; + }; + }; +}; + +&timer3 { + status = "disabled"; +}; + +&uart4 { + status = "disabled"; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + }; +}; + +/* disable the RTC node as its not accessible on the draco/dxr2 board */ +&rtc { + status = "disabled"; + ti,hwmods = "disabled"; +}; -- 1.8.5.3 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
