Hi, I've been experiencing USB issues with a BeagleBone white rev A5. I've not seen any symptoms with the TI 3.2 kernel but I need to get access to some of the later drivers and didn't fancy back porting...
So I've tried 3.8, 3,12 & 3.13 kernels with the patches from https://github.com/beagleboard/kernel and they seem to be able to talk to a USB memory stick but when making use of a cp210x and ftdi_sio based USB to UART adaptor the controller hangs. I've also tried linux-next, linux-usb and now linux-omap3 and they seem to be more unstable and even communicating with a USB stick seems flaky. I've got a test app that just writes "TESTING <count>\n" to the tty for ever. Here's some dmesg from linux-omap3 (1fbb354). I've added -DDEBUG to drivers/usb/{musb, serial}. OK: [ 16.573781] tty ttyUSB0: serial_write - 11 byte(s) [ 16.573802] cp210x ttyUSB0: usb_serial_generic_write_start - length = 11, data = 54 45 53 54 49 4e 47 20 34 32 0a [ 16.573825] musb-hdrc musb-hdrc.1.auto: qh ce474b00 periodic slot 10 [ 16.573846] musb-hdrc musb-hdrc.1.auto: qh ce474b00 urb ce489700 dev2 ep1out-bulk, hw_ep 10, ce44f700/11 [ 16.573866] musb-hdrc musb-hdrc.1.auto: --> hw10 urb ce489700 spd2 dev2 ep1out h_addr00 h_port00 bytes 11 [ 16.573887] musb-hdrc musb-hdrc.1.auto: configure ep10/a4 packet_sz=64, mode=0, dma_addr=0x8e44f700, len=11 is_tx=1 [ 16.573905] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 16.573928] musb-hdrc musb-hdrc.1.auto: DMA transfer done on hw_ep=10 bytes=11/11 [ 16.573945] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3500, dma [ 16.573986] musb-hdrc musb-hdrc.1.auto: complete ce489700 usb_serial_generic_write_bulk_callback+0x0/0xd4 [usbserial] (0), dev2 ep1out, 11/11 FAIL: [ 16.574085] tty ttyUSB0: serial_write - 11 byte(s) [ 16.574106] cp210x ttyUSB0: usb_serial_generic_write_start - length = 11, data = 54 45 53 54 49 4e 47 20 34 33 0a [ 16.574129] musb-hdrc musb-hdrc.1.auto: qh ce474b00 periodic slot 10 [ 16.574149] musb-hdrc musb-hdrc.1.auto: qh ce474b00 urb ce489700 dev2 ep1out-bulk, hw_ep 10, ce44f700/11 [ 16.574169] musb-hdrc musb-hdrc.1.auto: --> hw10 urb ce489700 spd2 dev2 ep1out h_addr00 h_port00 bytes 11 [ 16.574191] musb-hdrc musb-hdrc.1.auto: configure ep10/a4 packet_sz=64, mode=0, dma_addr=0x8e44f700, len=11 is_tx=1 [ 16.574208] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 16.574231] musb-hdrc musb-hdrc.1.auto: DMA transfer done on hw_ep=10 bytes=11/11 [ 16.574302] tty ttyUSB0: serial_write - 11 byte(s) [ 16.574322] cp210x ttyUSB0: usb_serial_generic_write_start - length = 11, data = 54 45 53 54 49 4e 47 20 34 34 0a [ 16.574381] tty ttyUSB0: serial_write - 11 byte(s) [ 16.574452] tty ttyUSB0: serial_write - 11 byte(s) [ 16.574508] tty ttyUSB0: serial_write - 11 byte(s) ... [ 16.930271] tty ttyUSB0: serial_write - 1 byte(s) Then my test app blocks. It looks like in the first fail case the DMA "succeeds", but the USB controller doesn't send the frame and consequently the TXPKTRDY bit in the csr register never gets cleared. Thus musb_is_tx_fifo_empty() always returns false and consequently falls into cppi41_recheck_tx_req() waiting for the queue to clear. Eventually we must fill up some buffer and cause my sending app to block. I've tried to force the FIFO to flush by setting the appropriate bits in the csr after a timeout and that doesn't seem to do anything. If I try and reboot the platform I get a punch of warnings: / # reboot The system is going down NOW! Sent SIGTERM to all processes [ 990.007339] ------------[ cut here ]------------ [ 990.014193] WARNING: CPU: 0 PID: 100 at drivers/dma/cppi41.c:605 cppi41_dma_control+0x230/0x2a8() [ 990.023567] Modules linked in: cp210x usbserial [ 990.028383] CPU: 0 PID: 100 Comm: blast Not tainted 3.14.0-rc2+ #3 [ 990.034967] [<c00148d8>] (unwind_backtrace) from [<c00115cc>] (show_stack+0x10/0x14) [ 990.043179] [<c00115cc>] (show_stack) from [<c073b784>] (dump_stack+0x68/0x84) [ 990.050823] [<c073b784>] (dump_stack) from [<c003a4b0>] (warn_slowpath_common+0x64/0x88) [ 990.059375] [<c003a4b0>] (warn_slowpath_common) from [<c003a4ec>] (warn_slowpath_null+0x18/0x1c) [ 990.068656] [<c003a4ec>] (warn_slowpath_null) from [<c0434cf8>] (cppi41_dma_control+0x230/0x2a8) [ 990.077948] [<c0434cf8>] (cppi41_dma_control) from [<c0543610>] (cppi41_dma_channel_abort+0x108/0x148) [ 990.087801] [<c0543610>] (cppi41_dma_channel_abort) from [<c053e5c8>] (musb_cleanup_urb+0x40/0x100) [ 990.097364] [<c053e5c8>] (musb_cleanup_urb) from [<c053e7a8>] (musb_urb_dequeue+0x120/0x154) [ 990.106293] [<c053e7a8>] (musb_urb_dequeue) from [<c05240e0>] (unlink1+0xb4/0xc4) [ 990.114206] [<c05240e0>] (unlink1) from [<c05254c8>] (usb_hcd_unlink_urb+0x60/0x80) [ 990.122304] [<c05254c8>] (usb_hcd_unlink_urb) from [<c052637c>] (usb_kill_urb+0x50/0xc8) [ 990.130917] [<c052637c>] (usb_kill_urb) from [<bf002c90>] (usb_serial_generic_close+0x20/0x64 [usbserial]) [ 990.141145] [<bf002c90>] (usb_serial_generic_close [usbserial]) from [<bf00fe88>] (cp210x_close+0xc/0x28 [cp210x]) [ 990.152094] [<bf00fe88>] (cp210x_close [cp210x]) from [<bf000024>] (serial_port_shutdown+0x24/0x28 [usbserial]) [ 990.162771] [<bf000024>] (serial_port_shutdown [usbserial]) from [<c044d484>] (tty_port_shutdown+0x6c/0x78) [ 990.173071] [<c044d484>] (tty_port_shutdown) from [<c044dee8>] (tty_port_close+0x24/0x4c) [ 990.181733] [<c044dee8>] (tty_port_close) from [<c0446120>] (tty_release+0x118/0x49c) [ 990.190029] [<c0446120>] (tty_release) from [<c012c600>] (__fput+0xd4/0x1e4) [ 990.197498] [<c012c600>] (__fput) from [<c0055974>] (task_work_run+0xb4/0xc8) [ 990.205045] [<c0055974>] (task_work_run) from [<c003cae0>] (do_exit+0x3f8/0x948) [ 990.212865] [<c003cae0>] (do_exit) from [<c003d0f4>] (do_group_exit+0x98/0xd4) [ 990.220512] [<c003d0f4>] (do_group_exit) from [<c004a9c4>] (get_signal_to_deliver+0x510/0x58c) [ 990.229616] [<c004a9c4>] (get_signal_to_deliver) from [<c0010a28>] (do_signal+0xa8/0x3b8) [ 990.238260] [<c0010a28>] (do_signal) from [<c0011034>] (do_work_pending+0x54/0x9c) [ 990.246264] [<c0011034>] (do_work_pending) from [<c000dea0>] (work_pending+0xc/0x20) [ 990.254441] ---[ end trace 6bbc95d827ba3e8c ]--- [ 991.506236] ------------[ cut here ]------------ [ 991.511118] WARNING: CPU: 0 PID: 100 at drivers/usb/musb/musb_host.c:128 musb_h_tx_flush_fifo+0x78/0xc4() [ 991.521219] Could not flush host TX10 fifo: csr: 2503 [ 991.526552] Modules linked in: cp210x usbserial [ 991.531352] CPU: 0 PID: 100 Comm: blast Tainted: G W 3.14.0-rc2+ #3 [ 991.538897] [<c00148d8>] (unwind_backtrace) from [<c00115cc>] (show_stack+0x10/0x14) [ 991.547081] [<c00115cc>] (show_stack) from [<c073b784>] (dump_stack+0x68/0x84) [ 991.554713] [<c073b784>] (dump_stack) from [<c003a4b0>] (warn_slowpath_common+0x64/0x88) [ 991.563262] [<c003a4b0>] (warn_slowpath_common) from [<c003a554>] (warn_slowpath_fmt+0x2c/0x3c) [ 991.572456] [<c003a554>] (warn_slowpath_fmt) from [<c053ccf0>] (musb_h_tx_flush_fifo+0x78/0xc4) [ 991.581651] [<c053ccf0>] (musb_h_tx_flush_fifo) from [<c053e62c>] (musb_cleanup_urb+0xa4/0x100) [ 991.590844] [<c053e62c>] (musb_cleanup_urb) from [<c053e7a8>] (musb_urb_dequeue+0x120/0x154) [ 991.599759] [<c053e7a8>] (musb_urb_dequeue) from [<c05240e0>] (unlink1+0xb4/0xc4) [ 991.607669] [<c05240e0>] (unlink1) from [<c05254c8>] (usb_hcd_unlink_urb+0x60/0x80) [ 991.615762] [<c05254c8>] (usb_hcd_unlink_urb) from [<c052637c>] (usb_kill_urb+0x50/0xc8) [ 991.624329] [<c052637c>] (usb_kill_urb) from [<bf002c90>] (usb_serial_generic_close+0x20/0x64 [usbserial]) [ 991.634544] [<bf002c90>] (usb_serial_generic_close [usbserial]) from [<bf00fe88>] (cp210x_close+0xc/0x28 [cp210x]) [ 991.645487] [<bf00fe88>] (cp210x_close [cp210x]) from [<bf000024>] (serial_port_shutdown+0x24/0x28 [usbserial]) [ 991.656156] [<bf000024>] (serial_port_shutdown [usbserial]) from [<c044d484>] (tty_port_shutdown+0x6c/0x78) [ 991.666452] [<c044d484>] (tty_port_shutdown) from [<c044dee8>] (tty_port_close+0x24/0x4c) [ 991.675095] [<c044dee8>] (tty_port_close) from [<c0446120>] (tty_release+0x118/0x49c) [ 991.683372] [<c0446120>] (tty_release) from [<c012c600>] (__fput+0xd4/0x1e4) [ 991.690824] [<c012c600>] (__fput) from [<c0055974>] (task_work_run+0xb4/0xc8) [ 991.698368] [<c0055974>] (task_work_run) from [<c003cae0>] (do_exit+0x3f8/0x948) [ 991.706184] [<c003cae0>] (do_exit) from [<c003d0f4>] (do_group_exit+0x98/0xd4) [ 991.713821] [<c003d0f4>] (do_group_exit) from [<c004a9c4>] (get_signal_to_deliver+0x510/0x58c) [ 991.722921] [<c004a9c4>] (get_signal_to_deliver) from [<c0010a28>] (do_signal+0xa8/0x3b8) [ 991.731564] [<c0010a28>] (do_signal) from [<c0011034>] (do_work_pending+0x54/0x9c) [ 991.739561] [<c0011034>] (do_work_pending) from [<c000dea0>] (work_pending+0xc/0x20) [ 991.747736] ---[ end trace 6bbc95d827ba3e8e ]--- Full dmesg: https://gist.github.com/anonymous/9124604 Anyone have any ideas on where else to look? I've put my defconfig here https://gist.github.com/anonymous/9124565 (it's based from the 3.13 one from the beagleboard github) just in case there is anything stupid going on. Is the USB in a known state of flux? Chris -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
