Add the High-Speed USB PHY.
Signed-off-by: Florian Vaussard <[email protected]>
---
arch/arm/boot/dts/omap3-overo-storm-tobi.dts | 16 ++++++++++
arch/arm/boot/dts/omap3-overo-tobi.dts | 16 ++++++++++
arch/arm/boot/dts/omap3-overo.dtsi | 44 ++++++++++++++++++++++++++++
3 files changed, 76 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts
b/arch/arm/boot/dts/omap3-overo-storm-tobi.dts
index 2033b52..eb93e3a 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts
+++ b/arch/arm/boot/dts/omap3-overo-storm-tobi.dts
@@ -21,6 +21,22 @@
};
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_2_pins
+ >;
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
/* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
/* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)
/* etk_d2.gpio_16 */
diff --git a/arch/arm/boot/dts/omap3-overo-tobi.dts
b/arch/arm/boot/dts/omap3-overo-tobi.dts
index 21de31d..e77be26 100644
--- a/arch/arm/boot/dts/omap3-overo-tobi.dts
+++ b/arch/arm/boot/dts/omap3-overo-tobi.dts
@@ -21,6 +21,22 @@
};
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_2_pins
+ >;
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
/* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
/* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
pinctrl-single,pins = <
OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)
/* etk_d2.gpio_16 */
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi
b/arch/arm/boot/dts/omap3-overo.dtsi
index 07467cc..8f810db 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -30,6 +30,24 @@
ti,codec = <&twl_audio>;
};
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio6 8 0>; /* gpio_168:
vbus enable */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */
+ vcc-supply = <&hsusb2_power>;
+ };
+
/* Regulator to trigger the nPoweron signal of the Wifi module */
w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
compatible = "regulator-fixed";
@@ -64,6 +82,11 @@
};
&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_pins
+ >;
+
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT |
PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
@@ -107,6 +130,19 @@
OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)
/* uart3_rts_sd.gpio_164 */
>;
};
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN |
MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)
/* i2c2_scl.gpio_168 */
+ OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4)
/* i2c2_sda.gpio_183 */
+ >;
+ };
};
&i2c1 {
@@ -168,6 +204,14 @@
power = <50>;
};
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
