Usage of pr_err is frowned upon, so replace it with dev_err. Aditionally, the message on nand_bch_init() error is redundant, since proper error is showed if the function fails.
Signed-off-by: Ezequiel Garcia <[email protected]> --- drivers/mtd/nand/omap2.c | 30 +++++++++++++++++------------- 1 file changed, 17 insertions(+), 13 deletions(-) diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index f97a4ff..3b357e9 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1375,7 +1375,7 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, erased_ecc_vec = bch16_vector; break; default: - pr_err("invalid driver configuration\n"); + dev_err(&info->pdev->dev, "invalid driver configuration\n"); return -EINVAL; } @@ -1446,7 +1446,8 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, err = 0; for (i = 0; i < eccsteps; i++) { if (err_vec[i].error_uncorrectable) { - pr_err("nand: uncorrectable bit-flips found\n"); + dev_err(&info->pdev->dev, + "uncorrectable bit-flips found\n"); err = -EBADMSG; } else if (err_vec[i].error_reported) { for (j = 0; j < err_vec[i].error_count; j++) { @@ -1483,8 +1484,9 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, 1 << bit_pos; } } else { - pr_err("invalid bit-flip @ %d:%d\n", - byte_pos, bit_pos); + dev_err(&info->pdev->dev, + "invalid bit-flip @ %d:%d\n", + byte_pos, bit_pos); err = -EBADMSG; } } @@ -1598,13 +1600,13 @@ static bool is_elm_present(struct omap_nand_info *info, /* check whether elm-id is passed via DT */ if (!elm_node) { - pr_err("nand: error: ELM DT node not found\n"); + dev_err(&info->pdev->dev, "ELM devicetree node not found\n"); return false; } pdev = of_find_device_by_node(elm_node); /* check whether ELM device is registered */ if (!pdev) { - pr_err("nand: error: ELM device not found\n"); + dev_err(&info->pdev->dev, "ELM device not found\n"); return false; } /* ELM module available, now configure it */ @@ -1734,14 +1736,14 @@ static int omap_nand_probe(struct platform_device *pdev) /* scan NAND device connected to chip controller */ nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16; if (nand_scan_ident(mtd, 1, NULL)) { - pr_err("nand device scan failed, may be bus-width mismatch\n"); + dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n"); err = -ENXIO; goto return_error; } /* check for small page devices */ if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) { - pr_err("small page devices are not supported\n"); + dev_err(&info->pdev->dev, "small page devices are not supported\n"); err = -EINVAL; goto return_error; } @@ -1896,8 +1898,9 @@ static int omap_nand_probe(struct platform_device *pdev) nand_chip->ecc.bytes, &ecclayout); if (!nand_chip->ecc.priv) { - pr_err("nand: error: unable to use s/w BCH library\n"); + dev_err(&info->pdev->dev, "unable to use BCH library\n"); err = -EINVAL; + goto return_error; } break; @@ -1959,7 +1962,7 @@ static int omap_nand_probe(struct platform_device *pdev) nand_chip->ecc.bytes, &ecclayout); if (!nand_chip->ecc.priv) { - pr_err("nand: error: unable to use s/w BCH library\n"); + dev_err(&info->pdev->dev, "unable to use BCH library\n"); err = -EINVAL; goto return_error; } @@ -2026,7 +2029,7 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; break; default: - pr_err("nand: error: invalid or unsupported ECC scheme\n"); + dev_err(&info->pdev->dev, "invalid or unsupported ECC scheme\n"); err = -EINVAL; goto return_error; } @@ -2038,8 +2041,9 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset; /* check if NAND device's OOB is enough to store ECC signatures */ if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) { - pr_err("not enough OOB bytes required = %d, available=%d\n", - ecclayout->eccbytes, mtd->oobsize); + dev_err(&info->pdev->dev, + "not enough OOB bytes required = %d, available=%d\n", + ecclayout->eccbytes, mtd->oobsize); err = -EINVAL; goto return_error; } -- 2.1.0 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
