Hi Roger,
On Friday 19 December 2014 05:35 PM, Roger Quadros wrote:
> Failed test case: Boot without SATA drive connected. Suspend/resume
> the board and then connect SATA drive. It fails to enumerate.
>
> Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
> we can't allow SATA DPLL to be in the unlocked state.
> The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
> Till now this clock was controlled by the AHCI SATA driver and was being
> shut off during system suspend (if the SATA drive was not already attached)
> causing the SATA DPLL to be unlocked and so causing errata i783.
>
> To prevent sata_ref_clk from being disabled, we move the control of
> this clock from the SATA AHCI driver to the SATA PHY driver and prevent
> it from being disabled.
>
> This also fixes the issue of SATA not working on OMAP5/DRA7 when
> AHCI platform driver is built as a module.
>
> Signed-off-by: Roger Quadros <rog...@ti.com>
> ---
> arch/arm/boot/dts/dra7.dtsi | 4 ++--
> arch/arm/boot/dts/omap5.dtsi | 4 ++--
> drivers/phy/phy-ti-pipe3.c | 53
> +++++++++++++++++++++++++++++++-------------
> 3 files changed, 41 insertions(+), 20 deletions(-)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index 63bf99b..8c35b84 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -1090,8 +1090,8 @@
> <0x4A096800 0x40>; /* pll_ctrl */
> reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> ctrl-module = <&omap_control_sata>;
> - clocks = <&sys_clkin1>;
> - clock-names = "sysclk";
> + clocks = <&sys_clkin1>, <&sata_ref_clk>;
> + clock-names = "sysclk", "refclk";
> #phy-cells = <0>;
> };
>
> diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
> index b321fdf..bb498e7 100644
> --- a/arch/arm/boot/dts/omap5.dtsi
> +++ b/arch/arm/boot/dts/omap5.dtsi
> @@ -929,8 +929,8 @@
> <0x4A096800 0x40>; /* pll_ctrl */
> reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> ctrl-module = <&omap_control_sata>;
> - clocks = <&sys_clkin>;
> - clock-names = "sysclk";
> + clocks = <&sys_clkin>, <&sata_ref_clk>;
> + clock-names = "sysclk", "refclk";
> #phy-cells = <0>;
> };
> };
> diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
> index e60ff14..e08edd9 100644
> --- a/drivers/phy/phy-ti-pipe3.c
> +++ b/drivers/phy/phy-ti-pipe3.c
> @@ -85,6 +85,7 @@ struct ti_pipe3 {
> struct pipe3_dpll_map *dpll_map;
> u8 id;
> bool enabled;
> + bool refclk_enabled; /* this flag is needed specifically for SATA */
> spinlock_t lock; /* serialize clock enable/disable */
> };
>
> @@ -333,21 +334,20 @@ static int ti_pipe3_probe(struct platform_device *pdev)
> }
> }
>
> + phy->refclk = devm_clk_get(phy->dev, "refclk");
> + if (IS_ERR(phy->refclk)) {
> + dev_err(&pdev->dev, "unable to get refclk\n");
> + return PTR_ERR(phy->refclk);
> + }
This will break older dtbs. AFAIK, newer kernels should be compatible with
older dtbs too. cc'ed devicet...@vger.kernel.org for clarification.
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
