On Tue 2015-01-06 08:59:03, Tony Lindgren wrote:
> * Pavel Machek <[email protected]> [150106 00:03]:
> > On Mon 2015-01-05 15:02:29, Tony Lindgren wrote:
> > > Revert "ARM: dts: Disable smc91x on n900 until bootloader
> > > dependency is removed". We've now fixed the issues that
> > > caused problems with uninitialized hardware depending on
> > > the bootloader version. Mostly things got fixed with
> > > the following commits:
> > >
> > > 9a894953a97b ("ARM: dts: Fix bootloader version dependencies by muxing
> > > n900 smc91x pins")
> > > 7d2911c43815 ("net: smc91x: Fix gpios for device tree based booting")
> > >
> > > Note that this only affects the early development boards
> > > with Ethernet that we still have in a few automated boot
> > > test systems.
> > >
> > > Signed-off-by: Tony Lindgren <[email protected]>
> >
> > Normally, the early development boards should have separate dts file
> > (then include common parts), no?
>
> In this case it won't matter. The GPMC hardware is there, the probe
> just fails if no smsc91x is found.
>
> > Could you at least add a note to the dts file what is it? Because I
> > always thought it is a bug.
>
> Sure, updated patch below. Can somebody please test boot it on
> a production n900 too to make sure it no longer causes issues?
Actually... how do you manage your n900 to boot? Does it also boot
from 0xffff?
I believe I'm hitting dtb size limit (again), and 3.19-rc3 does not boot
unless I somehow make dtb smaller... like the patch below.
---
make dtb smaller so that it boots.
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 53f3ca0..82f4597 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -140,14 +140,6 @@
>;
};
- ethernet_pins: pinmux_ethernet_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN |
MUX_MODE4) /* gpmc_ncs3.gpio_54 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4)
/* dss_data16.gpio_86 */
- OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)
/* uart3_rts_sd.gpio_164 */
- >;
- };
-
gpmc_pins: pinmux_gpmc_pins {
pinctrl-single,pins = <
@@ -700,42 +692,6 @@
};
};
- ethernet@gpmc {
- compatible = "smsc,lan91c94";
-
- status = "disabled";
-
- interrupt-parent = <&gpio2>;
- interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
- reg = <1 0x300 0xf>; /* 16 byte IO range at offset
0x300 */
- bank-width = <2>;
- pinctrl-names = "default";
- pinctrl-0 = <ðernet_pins>;
- power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */
- reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */
- gpmc,device-width = <2>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <48>;
- gpmc,cs-wr-off-ns = <24>;
- gpmc,adv-on-ns = <0>;
- gpmc,adv-rd-off-ns = <0>;
- gpmc,adv-wr-off-ns = <0>;
- gpmc,we-on-ns = <12>;
- gpmc,we-off-ns = <18>;
- gpmc,oe-on-ns = <12>;
- gpmc,oe-off-ns = <48>;
- gpmc,page-burst-access-ns = <0>;
- gpmc,access-ns = <42>;
- gpmc,rd-cycle-ns = <180>;
- gpmc,wr-cycle-ns = <180>;
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wr-access-ns = <0>;
- gpmc,wr-data-mux-bus-ns = <12>;
- };
};
&mcspi1 {
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures)
http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
