Hello Andrew,
On Sat, Oct 24, 2015 at 2:05 PM, Andrew F. Davis <a...@ti.com> wrote:
> Using constants for pinctrl allows better readability and removes
> redundancy with comments. AM33XX_IOPAD allows us to use part of the
> pinctrl physical address as in the TRM instead of an offset.
>
> Signed-off-by: Andrew F. Davis <a...@ti.com>
> ---
> arch/arm/boot/dts/am335x-boneblack.dts | 44
> +++++++++++++++++-----------------
> 1 file changed, 22 insertions(+), 22 deletions(-)
>
> diff --git a/arch/arm/boot/dts/am335x-boneblack.dts
> b/arch/arm/boot/dts/am335x-boneblack.dts
> index eadbba3..346f529 100644
> --- a/arch/arm/boot/dts/am335x-boneblack.dts
> +++ b/arch/arm/boot/dts/am335x-boneblack.dts
> @@ -36,32 +36,32 @@
> &am33xx_pinmux {
> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
> pinctrl-single,pins = <
> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 |
> AM33XX_PIN_OUTPUT */
> - 0xa0 0x08 /* lcd_data0.lcd_data0,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa4 0x08 /* lcd_data1.lcd_data1,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa8 0x08 /* lcd_data2.lcd_data2,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xac 0x08 /* lcd_data3.lcd_data3,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb0 0x08 /* lcd_data4.lcd_data4,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb4 0x08 /* lcd_data5.lcd_data5,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb8 0x08 /* lcd_data6.lcd_data6,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xbc 0x08 /* lcd_data7.lcd_data7,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc0 0x08 /* lcd_data8.lcd_data8,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc4 0x08 /* lcd_data9.lcd_data9,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc8 0x08 /* lcd_data10.lcd_data10,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xcc 0x08 /* lcd_data11.lcd_data11,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd0 0x08 /* lcd_data12.lcd_data12,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd4 0x08 /* lcd_data13.lcd_data13,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd8 0x08 /* lcd_data14.lcd_data14,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xdc 0x08 /* lcd_data15.lcd_data15,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xe0 0x00 /* lcd_vsync.lcd_vsync,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe4 0x00 /* lcd_hsync.lcd_hsync,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0
> | AM33XX_PIN_OUTPUT */
> - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en,
> OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> + AM33XX_IOPAD(0x9b0, (PIN_OUTPUT_PULLDOWN |
> MUX_MODE3)) /* xdma_event_intr0 */
I missed when I first reviewed this patch but there is no need to
enclose the padconf values into parenthesis, for example the following
is easier to read and is preferred IMHO:
AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
Same for all the other pinctrl lines.
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
