Matthias, Please avoid top-posting, because its prohibited by the mailing list rules. I'm readjusting it for you below:
From: matthias schwarz [mailto:[email protected]] > 2009/7/27 matthias schwarz <[email protected]>: > > 2009/7/27 Aguirre Rodriguez, Sergio Alberto <[email protected]>: > >> (rearranging mail to avoid top posting..) > >> > >> From: matthias schwarz [mailto:[email protected]] > >>> 2009/7/27 Aguirre Rodriguez, Sergio Alberto <[email protected]>: > >>> > > >>> > > >>> >> -----Original Message----- > >>> >> From: [email protected] [mailto:linux-omap- > >>> >> [email protected]] On Behalf Of matthias schwarz > >>> >> Sent: Monday, July 27, 2009 7:47 AM > >>> >> To: [email protected] > >>> >> Subject: Camera Interface VS/HS Issue > >>> >> > >>> >> Hi there, > >>> >> > >>> >> i just recently ran into a problem when trying to let the ISP > >>> >> (OMAP3530) generate HS/VS signals in SYNC mode. > >>> >> I am building a module to do so. > >>> >> > >>> >> It basically enables the three clocks (cam_ick, cam_mclk and > >>> >> csi2_96m_fck), > >>> >> then sets > >>> >> > >>> >> ISPCCDC_PIX_LINES_PPLN > >>> >> ISPCCDC_PIX_LINES_HLPRF > >>> >> ISPCCDC_HD_VD_WID_VDW > >>> >> ISPCCDC_HD_VD_WID_HDW > >>> >> ISPCCDC_SYN_MODE_VDHDEN > >>> >> ISPCCDC_SYN_MODE_VDHDOUT > >>> >> ISPCCDC_CFG_VDLC > >>> >> ISPTCTRL_CTRL_DIVA > >>> >> ISPTCTRL_CTRL_DIVB > >>> >> ISPCCDC_PCR > >>> >> > >>> >> via some calls to ioremap and ioread32/iowrite32. > >>> >> My question now is the following: > >>> >> when i hook an oscilloscope to the corresponding pins (CAM_VS, > CAM_HS, > >>> >> CAM_XCLKA) i can see that only the CAM_XCLKA is working correctly, > >>> >> also at the configured frequency. > >>> >> Both, CAM_VS and CAM_HS remain at low voltage all the time, even > when > >>> >> i switch their polarities (ISPCCDC_SYN_MODE_VDPOL, > >>> >> ISPCCDC_SYN_MODE_HDPOL) that behavior does not change and signals > >>> >> always remain at low voltage. > >>> >> > >>> >> Could someone help me out, or give me a hint what i might be > missing > >>> >> to generate those output signals correctly? > >>> > > >>> > Matthias, > >>> > > >>> > Can you please provide a register dump of the above values? > >>> > > >>> > Looks like you're touching the adequate registers though... But I > can > >>> help you more looking at the values. > >>> > > >>> Sure i can, > >>> register values are the following: > >>> > >>> ccdc_pix_lines: 0x050005a0 > >>> > >>> ccdc_hd_vd_wid: 0x00320064 > >>> > >>> ccdc_syn_mode: 0x00050c0c > >> > >> This is wrong, because: > >> > >> Bit0 sets directions of cam_hs and cam_vs signals with this values: > >> - 0: Input (what you're setting with that values) > >> - 1: Output (Is this what you want?) > >> > >> Bit1 Sets direction of cam_fld pin, which follows the same logic as the > Bit0. > >> > >> Others could be wrong or bad, depending on your exact usecase and > config intention. > >> > >> Hope this helps. > >> > > Hmm, > > so now i have: > > > > ccdc_syn_mode: 0x00050c0f > > > > but that does not change the behavior i am experiencing, both pins > > (CAM_VS, CAM_HS) remain at low voltage at all times. > > > > I don't have to do anything but enabling the corresponding clocks to > > make sure the CCDC is working? > I also set, > > ISPCTRL_CCDC_CLK_EN > ISPCTRL_CCDC_RAM_EN > > but those also won't change the always low voltage pins. Are you having a valid Pixel clock input to the CCDC? I just confirmed with our internal TI HW support, and you need a valid pixel input clock to assert/deassert the signals. Regards, Sergio > > > > Thank you, > > Matthias > >> Regards, > >> Sergio > >>> > >>> ccdc_cfg: 0x00008000 > >>> > >>> tctrl_ctrl_cfg: 0x80000463 > >>> > >>> ccdc_pcr: 0x00000001 > >>> > >>> Thank you, > >>> Matthias > >>> > Regards, > >>> > Sergio > >>> >> > >>> >> Thank you very much, > >>> >> Matthias > >>> >> -- > >>> >> To unsubscribe from this list: send the line "unsubscribe linux- > omap" > >>> in > >>> >> the body of a message to [email protected] > >>> >> More majordomo info at http://vger.kernel.org/majordomo-info.html > >>> > > >>> > > >> > >> > > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
