After the patch series "[PATCH 00/14] OMAP PM fixes for .31-rc" merge in 2.6.31-rc5 console was not working for OMAP4. This patch fixes it by adding UART4 support.
The mentioned patch series has split the UART platform data into separate structure hence needs to rework the first patch. More info- http://lkml.org/lkml/2009/8/20/192 Without this patch omap_serial_init() would produce kernel crash on OMAP4430 platform while looping for UART4 platform data. Signed-off-by: Syed Rafiuddin <[email protected]> Signed-off-by: Santosh Shilimkar <[email protected]> --- arch/arm/mach-omap2/board-4430sdp.c | 2 +- arch/arm/mach-omap2/serial.c | 27 ++++++++++++++++++++++++++- 2 files changed, 27 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index b0c7402..1b22307 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -39,7 +39,7 @@ static struct platform_device *sdp4430_devices[] __initdata = { }; static struct omap_uart_config sdp4430_uart_config __initdata = { - .enabled_uarts = (1 << 0) | (1 << 1) | (1 << 2), + .enabled_uarts = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3), }; static struct omap_lcd_config sdp4430_lcd_config __initdata = { diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index a7421a5..e1be77b 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -112,7 +112,21 @@ static struct plat_serial8250_port serial_platform_data2[] = { .flags = 0 } }; - +#ifdef CONFIG_ARCH_OMAP4 +static struct plat_serial8250_port serial_platform_data3[] = { + { + .membase = IO_ADDRESS(OMAP_UART4_BASE), + .mapbase = OMAP_UART4_BASE, + .irq = 70, + .flags = UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = OMAP24XX_BASE_BAUD * 16, + }, { + .flags = 0 + } +}; +#endif static inline unsigned int serial_read_reg(struct plat_serial8250_port *up, int offset) { @@ -550,6 +564,17 @@ static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = { }, }, }, +#ifdef CONFIG_ARCH_OMAP4 + { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_FOURPORT, + .dev = { + .platform_data = serial_platform_data3, + }, + }, + }, +#endif }; void __init omap_serial_init(void) -- 1.5.4.7 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
