>-----Original Message----- >From: [email protected] >[mailto:[email protected]] On Behalf Of Enric >Balletbò i Serra >Sent: Wednesday, October 14, 2009 3:32 AM >To: [email protected] >Subject: [PATCH 1/2] ARM: OMAP3: Add support for the IGEP v2 board (rev B) > >This patch adds minimal IGEP v2 support.
Could you give some link giving details of the board please. > >The IGEP v2 board is a low-cost, fan-less and industrial temperature >range single board computer that unleashes laptop-like performance and >expandability without the bulk, expense, or noise of typical desktop >machines. Its architecture shares much in common with other OMAP3 boards. > >Signed-off-by: Enric Balletbo i Serra <[email protected]> >--- > arch/arm/mach-omap2/Kconfig | 4 + > arch/arm/mach-omap2/Makefile | 2 + > arch/arm/mach-omap2/board-igep0020.c | 252 ++++++++++++++++++++++++++++++++++ > 3 files changed, 258 insertions(+), 0 deletions(-) > create mode 100644 arch/arm/mach-omap2/board-igep0020.c > >diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig >index 75b1c7e..9936510 100644 >--- a/arch/arm/mach-omap2/Kconfig >+++ b/arch/arm/mach-omap2/Kconfig >@@ -85,6 +85,10 @@ config MACH_OMAP_ZOOM2 > bool "OMAP3 Zoom2 board" > depends on ARCH_OMAP3 && ARCH_OMAP34XX > >+config MACH_IGEP0020 >+ bool "IGEP0020" >+ depends on ARCH_OMAP3 && ARCH_OMAP34XX >+ > config MACH_OMAP_4430SDP > bool "OMAP 4430 SDP board" > depends on ARCH_OMAP4 >diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile >index 6b7702f..df0bdc4 100644 >--- a/arch/arm/mach-omap2/Makefile >+++ b/arch/arm/mach-omap2/Makefile >@@ -74,6 +74,8 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o >\ > obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ > mmc-twl4030.o \ > board-zoom-debugboard.o >+obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o \ >+ mmc-twl4030.o \ > > obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o > >diff --git a/arch/arm/mach-omap2/board-igep0020.c >b/arch/arm/mach-omap2/board-igep0020.c >new file mode 100644 >index 0000000..15175e0 >--- /dev/null >+++ b/arch/arm/mach-omap2/board-igep0020.c >@@ -0,0 +1,252 @@ >+/* >+ * Copyright (C) 2009 Integration Software and Electronic Engineering. >+ * >+ * Modified from mach-omap2/board-generic.c >+ * >+ * This program is free software; you can redistribute it and/or modify >+ * it under the terms of the GNU General Public License version 2 as >+ * published by the Free Software Foundation. >+ */ >+ >+#include <linux/kernel.h> >+#include <linux/init.h> >+#include <linux/delay.h> >+#include <linux/platform_device.h> >+#include <linux/input.h> >+#include <linux/gpio.h> >+#include <linux/i2c/twl4030.h> >+#include <linux/regulator/machine.h> >+ >+#include <asm/mach-types.h> >+#include <asm/mach/arch.h> >+ >+#include <mach/common.h> >+#include <mach/gpmc.h> >+#include <mach/onenand.h> >+#include <mach/usb.h> >+ >+#include "mmc-twl4030.h" >+ >+#define IGEP2_SMSC911X_CS 5 >+#define IGEP2_SMSC911X_GPIO 176 >+#define IGEP2_GPIO_LED_0_RED 26 >+#define IGEP2_GPIO_LED_0_GREEN 27 >+#define IGEP2_GPIO_LED_1_RED 28 >+ >+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) >+ >+#include <linux/smsc911x.h> >+ >+static struct resource igep2_smsc911x_resources[] = { >+ { >+ .name = "smsc911x-memory", >+ .flags = IORESOURCE_MEM, >+ }, >+ { >+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, >+ }, >+}; >+ >+static struct smsc911x_platform_config igep2_smsc911x_config = { >+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, >+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, >+ .flags = SMSC911X_USE_32BIT , >+ .phy_interface = PHY_INTERFACE_MODE_MII, >+}; >+ >+static struct platform_device igep2_smsc911x_device = { >+ .name = "smsc911x", >+ .id = -1, >+ .num_resources = ARRAY_SIZE(igep2_smsc911x_resources), >+ .resource = igep2_smsc911x_resources, >+ .dev = { >+ .platform_data = &igep2_smsc911x_config, >+ }, >+}; >+ >+static inline void __init igep2_init_smsc911x(void) >+{ >+ unsigned long cs_mem_base; >+ >+ if (gpmc_cs_request(IGEP2_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) { >+ pr_warning("igep2_init_smsc911x: " >+ "Failed request for GPMC mem\n"); >+ gpmc_cs_free(IGEP2_SMSC911X_CS); >+ return; >+ } >+ >+ igep2_smsc911x_resources[0].start = cs_mem_base + 0x0; >+ igep2_smsc911x_resources[0].end = cs_mem_base + 0xff; >+ >+ if ((gpio_request(IGEP2_SMSC911X_GPIO, "SMSC911X IRQ") == 0) && >+ (gpio_direction_input(IGEP2_SMSC911X_GPIO) == 0)) { >+ gpio_export(IGEP2_SMSC911X_GPIO, 0); >+ } else { >+ pr_warning("igep2_init_smsc911x: " >+ "Could not obtain gpio for IRQ\n"); >+ return; >+ } >+ >+ igep2_smsc911x_resources[1].start = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO); >+ igep2_smsc911x_resources[1].end = 0; >+ >+ platform_device_register(&igep2_smsc911x_device); >+} >+ >+#else >+ >+static inline void __init igep2_init_smsc911x(void) { } >+ >+#endif >+ >+static struct omap_board_config_kernel igep2_config[] __initdata = { >+}; >+ >+static struct regulator_consumer_supply igep2_vmmc1_supply = { >+ .supply = "vmmc", >+}; >+ >+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ >+static struct regulator_init_data igep2_vmmc1 = { >+ .constraints = { >+ .min_uV = 1850000, >+ .max_uV = 3150000, >+ .valid_modes_mask = REGULATOR_MODE_NORMAL >+ | REGULATOR_MODE_STANDBY, >+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE >+ | REGULATOR_CHANGE_MODE >+ | REGULATOR_CHANGE_STATUS, >+ }, >+ .num_consumer_supplies = 1, >+ .consumer_supplies = &igep2_vmmc1_supply, >+}; >+ >+static struct twl4030_hsmmc_info mmc[] __initdata = { >+ { >+ .mmc = 1, >+ .wires = 4, >+ .gpio_wp = -EINVAL, >+ }, >+ { >+ .mmc = 2, >+ .wires = 4, >+ .gpio_cd = -EINVAL, >+ .gpio_wp = -EINVAL, >+ }, >+ {} /* Terminator */ >+}; >+ >+static int igep2_twl_gpio_setup(struct device *dev, >+ unsigned gpio, unsigned ngpio) >+{ >+ /* gpio + 0 is "mmc0_cd" (input/IRQ) */ >+ mmc[0].gpio_cd = gpio + 0; >+ twl4030_mmc_init(mmc); >+ >+ /* link regulators to MMC adapters ... we "know" the >+ * regulators will be set up only *after* we return. >+ */ >+ igep2_vmmc1_supply.dev = mmc[0].dev; >+ >+ return 0; >+}; >+ >+static struct twl4030_usb_data igep2_usb_data = { >+ .usb_mode = T2_USB_MODE_ULPI, >+}; >+ >+static void __init igep2_init_irq(void) >+{ >+ omap_board_config = igep2_config; >+ omap_board_config_size = ARRAY_SIZE(igep2_config); >+ omap2_init_common_hw(NULL, NULL); >+ omap_init_irq(); >+ omap_gpio_init(); >+} >+ >+static struct twl4030_gpio_platform_data igep2_gpio_data = { >+ .gpio_base = OMAP_MAX_GPIO_LINES, >+ .irq_base = TWL4030_GPIO_IRQ_BASE, >+ .irq_end = TWL4030_GPIO_IRQ_END, >+ .setup = igep2_twl_gpio_setup, >+}; >+ >+static struct twl4030_platform_data igep2_twldata = { >+ .irq_base = TWL4030_IRQ_BASE, >+ .irq_end = TWL4030_IRQ_END, >+ >+ /* platform_data for children goes here */ >+ .usb = &igep2_usb_data, >+ .gpio = &igep2_gpio_data, >+ .vmmc1 = &igep2_vmmc1, >+ >+}; >+ >+static struct i2c_board_info __initdata igep2_i2c_boardinfo[] = { >+ { >+ I2C_BOARD_INFO("twl4030", 0x48), >+ .flags = I2C_CLIENT_WAKE, >+ .irq = INT_34XX_SYS_NIRQ, >+ .platform_data = &igep2_twldata, >+ }, >+}; >+ >+static int __init igep2_i2c_init(void) >+{ >+ omap_register_i2c_bus(1, 2600, igep2_i2c_boardinfo, >+ ARRAY_SIZE(igep2_i2c_boardinfo)); >+ /* Bus 3 is attached to the DVI port where devices like the pico DLP >+ * projector don't work reliably with 400kHz */ >+ omap_register_i2c_bus(3, 100, NULL, 0); >+ return 0; >+} >+ >+static void __init igep2_init(void) >+{ >+ igep2_i2c_init(); >+ omap_serial_init(); >+ usb_musb_init(); >+ >+ igep2_init_smsc911x(); >+ >+ /* GPIO userspace leds */ >+ if ((gpio_request(IGEP2_GPIO_LED_0_RED, "GPIO_LED_0_RED") == 0) && >+ (gpio_direction_output(IGEP2_GPIO_LED_0_RED, 1) == 0)) { >+ gpio_export(IGEP2_GPIO_LED_0_RED, 0); >+ gpio_set_value(IGEP2_GPIO_LED_0_RED, 0); >+ } else >+ pr_warning("igep2_init: " >+ "Could not obtain gpio for GPIO_LED_0_RED\n"); >+ >+ if ((gpio_request(IGEP2_GPIO_LED_0_GREEN, "GPIO_LED_0_GREEN") == 0) && >+ (gpio_direction_output(IGEP2_GPIO_LED_0_GREEN, 1) == 0)) { >+ gpio_export(IGEP2_GPIO_LED_0_GREEN, 0); >+ gpio_set_value(IGEP2_GPIO_LED_0_GREEN, 0); >+ } else >+ pr_warning("igep2_init: " >+ "Could not obtain gpio for GPIO_LED_0_GREEN\n"); >+ >+ if ((gpio_request(IGEP2_GPIO_LED_1_RED, "GPIO_LED_1_RED") == 0) && >+ (gpio_direction_output(IGEP2_GPIO_LED_1_RED, 1) == 0)) { >+ gpio_export(IGEP2_GPIO_LED_1_RED, 0); >+ gpio_set_value(IGEP2_GPIO_LED_1_RED, 0); >+ } else >+ pr_warning("igep2_init: " >+ "Could not obtain gpio for GPIO_LED_1_RED\n"); >+} >+ >+static void __init igep2_map_io(void) >+{ >+ omap2_set_globals_343x(); >+ omap2_map_common_io(); >+} >+ >+MACHINE_START(IGEP0020, "IGEP v2 board") >+ .phys_io = 0x48000000, >+ .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, >+ .boot_params = 0x80000100, >+ .map_io = igep2_map_io, >+ .init_irq = igep2_init_irq, >+ .init_machine = igep2_init, >+ .timer = &omap_timer, >+MACHINE_END >-- >1.5.4.3 >-- >To unsubscribe from this list: send the line "unsubscribe linux-omap" in >the body of a message to [email protected] >More majordomo info at http://vger.kernel.org/majordomo-info.html
