Kevin,
I have following changes on top of this patch,
1.) Updated omap_uart_port_info as per your comments.
2.) Added Errata 2.15 for DMA mode.
3.) Fix compilation error if omap-serial is enabled with 8250.
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index c067416..cbe1f76 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -249,10 +249,18 @@ static inline void omap_uart_smart_idle_enable(struct
omap_uart_state *p,
sysc = omap_hwmod_read_sysc(p->oh);
sysc &= ~SYSC_SIDLEMODE_MASK;
- if (enable)
- sysc |= 0x2 << SYSC_SIDLEMODE_SHIFT;
- else
+ if (enable) {
+ /**
+ * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
+ * in Smartidle Mode When Configured for DMA Operations.
+ */
+ if (p->dma_enabled)
+ sysc |= 0x0 << SYSC_SIDLEMODE_SHIFT;
+ else
+ sysc |= 0x2 << SYSC_SIDLEMODE_SHIFT;
+ } else {
sysc |= 0x1 << SYSC_SIDLEMODE_SHIFT;
+ }
omap_hwmod_write_sysc(sysc, p->oh);
}
@@ -540,14 +548,17 @@ void __init omap_serial_early_init(void)
void __init omap_serial_init(void)
{
struct omap_uart_state *uart;
+ char *name;
list_for_each_entry(uart, &uart_list, node) {
struct omap_hwmod *oh = uart->oh;
struct omap_device *od;
void *pdata = NULL;
u32 pdata_size = 0;
+
+ uart->dma_enabled = 0;
#ifdef CONFIG_SERIAL_8250_CONSOLE
- char *name = "serial8250";
+ name = "serial8250";
struct plat_serial8250_port ports[2] = {
{},
{.flags = 0},
@@ -578,14 +589,20 @@ void __init omap_serial_init(void)
pdata_size = 2 * sizeof(struct plat_serial8250_port);
#endif
#ifdef CONFIG_SERIAL_OMAP_CONSOLE
- struct uart_port_info p;
- char *name = "omap-hsuart";
+ struct omap_uart_port_info omap_up;
+ name = "omap-hsuart";
+
+ omap_up.dma_enabled = 0;
+ uart->dma_enabled = omap_up.dma_enabled;
- p.dma_enabled = 0;
- p.uartclk = OMAP24XX_BASE_BAUD * 16;
+ omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
+ omap_up.mapbase = oh->slaves[0]->addr->pa_start;
+ omap_up.membase = oh->_rt_va;
+ omap_up.irqflags = IRQF_SHARED;
+ omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
- pdata = &p;
- pdata_size = sizeof(struct uart_port_info);
+ pdata = &omap_up;
+ pdata_size = sizeof(struct omap_uart_port_info);
#endif
if (WARN_ON(!oh))
Do you want me to re-post this patch integrating the above changes?
If changes are fine with you.
--
Regards,
Govindraj.R
On Wed, Nov 25, 2009 at 1:26 AM, Kevin Hilman <[email protected]>
wrote:
> Convert UART core and PM support to use omap_device layer. Also add
> support for both console on 8250 or omap-serial driver.
>
> omap_device conversion:
> - Convert clock API calls to omap_device calls
> - Remove all static platform_data setup and configuration. This is
> all done by the omap_device build phase.
>
> Known issues:
> - broken on OMAP4 until OMAP4 UART hwmods are available
>
> Signed-off-by: Kevin Hilman <[email protected]>
> ---
> arch/arm/mach-omap2/serial.c | 338
> +++++++++++++++++++-----------------------
> 1 files changed, 154 insertions(+), 184 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
> index 3595ffa..c067416 100644
> --- a/arch/arm/mach-omap2/serial.c
> +++ b/arch/arm/mach-omap2/serial.c
> @@ -24,20 +24,33 @@
> #include <linux/io.h>
> #include <linux/platform_device.h>
>
> +#ifdef CONFIG_SERIAL_8250_CONSOLE
> +#include <linux/serial_8250.h>
> +#endif
> +
> +#ifdef CONFIG_SERIAL_OMAP_CONSOLE
> +#include <plat/omap-serial.h>
> +#endif
> +
> #include <plat/common.h>
> #include <plat/board.h>
> #include <plat/clock.h>
> #include <plat/control.h>
> #include <plat/dma.h>
> +#include <plat/omap_hwmod.h>
> +#include <plat/omap_device.h>
>
> #include "prm.h"
> #include "pm.h"
> +#include "cm.h"
> #include "prm-regbits-34xx.h"
>
> #define UART_OMAP_WER 0x17 /* Wake-up enable register */
>
> #define DEFAULT_TIMEOUT (5 * HZ)
>
> +#define MAX_UART_HWMOD_NAME_LEN 16
> +
> struct omap_uart_state {
> int num;
> int can_sleep;
> @@ -61,7 +74,8 @@ struct omap_uart_state {
> resource_size_t mapbase;
>
> struct list_head node;
> - struct platform_device pdev;
> + struct omap_hwmod *oh;
> + struct platform_device *pdev;
>
> #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
> int context_valid;
> @@ -78,102 +92,13 @@ struct omap_uart_state {
>
> static LIST_HEAD(uart_list);
>
> -#ifdef CONFIG_SERIAL_8250
> -#include <linux/serial_8250.h>
> -
> -static struct plat_serial8250_port serial_platform_data0[] = {
> - {
> - .mapbase = OMAP_UART1_BASE,
> - .irq = 72,
> - .flags = UPF_BOOT_AUTOCONF,
> - .iotype = UPIO_MEM,
> - .regshift = 2,
> - .uartclk = OMAP24XX_BASE_BAUD * 16,
> - }, {
> - .flags = 0
> - }
> -};
> -
> -static struct plat_serial8250_port serial_platform_data1[] = {
> - {
> - .mapbase = OMAP_UART2_BASE,
> - .irq = 73,
> - .flags = UPF_BOOT_AUTOCONF,
> - .iotype = UPIO_MEM,
> - .regshift = 2,
> - .uartclk = OMAP24XX_BASE_BAUD * 16,
> - }, {
> - .flags = 0
> - }
> -};
> -
> -static struct plat_serial8250_port serial_platform_data2[] = {
> +static struct omap_device_pm_latency omap_uart_latency[] = {
> {
> - .mapbase = OMAP_UART3_BASE,
> - .irq = 74,
> - .flags = UPF_BOOT_AUTOCONF,
> - .iotype = UPIO_MEM,
> - .regshift = 2,
> - .uartclk = OMAP24XX_BASE_BAUD * 16,
> - }, {
> - .flags = 0
> - }
> -};
> -
> -#ifdef CONFIG_ARCH_OMAP4
> -static struct plat_serial8250_port serial_platform_data3[] = {
> - {
> - .mapbase = OMAP_UART4_BASE,
> - .irq = 70,
> - .flags = UPF_BOOT_AUTOCONF,
> - .iotype = UPIO_MEM,
> - .regshift = 2,
> - .uartclk = OMAP24XX_BASE_BAUD * 16,
> - }, {
> - .flags = 0
> - }
> -};
> -#endif
> -
> -static struct omap_uart_state omap_uart[] = {
> - {
> - .pdev = {
> - .name = "serial8250",
> - .id = PLAT8250_DEV_PLATFORM,
> - .dev = {
> - .platform_data = serial_platform_data0,
> - },
> - },
> - }, {
> - .pdev = {
> - .name = "serial8250",
> - .id = PLAT8250_DEV_PLATFORM1,
> - .dev = {
> - .platform_data = serial_platform_data1,
> - },
> - },
> - }, {
> - .pdev = {
> - .name = "serial8250",
> - .id = PLAT8250_DEV_PLATFORM2,
> - .dev = {
> - .platform_data = serial_platform_data2,
> - },
> - },
> - },
> -#ifdef CONFIG_ARCH_OMAP4
> - {
> - .pdev = {
> - .name = "serial8250",
> - .id = 3,
> - .dev = {
> - .platform_data = serial_platform_data3,
> - },
> - },
> + .deactivate_func = omap_device_idle_hwmods,
> + .activate_func = omap_device_enable_hwmods,
> + .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
> },
> -#endif
> };
> -#endif
>
> static inline unsigned int serial_read_reg(struct omap_uart_state *up,
> int offset)
> @@ -200,7 +125,6 @@ static inline void __init omap_uart_reset(struct
> omap_uart_state *p)
> serial_write_reg(p, UART_OMAP_MDR1, 0x07);
> serial_write_reg(p, UART_OMAP_SCR, 0x08);
> serial_write_reg(p, UART_OMAP_MDR1, 0x00);
> - serial_write_reg(p, UART_OMAP_SYSC, (0x02 << 3) | (1 << 2) | (1 <<
> 0));
> }
>
> #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
> @@ -267,8 +191,7 @@ static inline void omap_uart_enable_clocks(struct
> omap_uart_state *uart)
> if (uart->clocked)
> return;
>
> - clk_enable(uart->ick);
> - clk_enable(uart->fck);
> + omap_device_enable(uart->pdev);
> uart->clocked = 1;
> omap_uart_restore_context(uart);
> }
> @@ -282,8 +205,7 @@ static inline void omap_uart_disable_clocks(struct
> omap_uart_state *uart)
>
> omap_uart_save_context(uart);
> uart->clocked = 0;
> - clk_disable(uart->ick);
> - clk_disable(uart->fck);
> + omap_device_idle(uart->pdev);
> }
>
> static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
> @@ -320,18 +242,18 @@ static void omap_uart_disable_wakeup(struct
> omap_uart_state *uart)
> }
> }
>
> -static void omap_uart_smart_idle_enable(struct omap_uart_state *p,
> - int enable)
> +static inline void omap_uart_smart_idle_enable(struct omap_uart_state *p,
> + int enable)
> {
> - u16 sysc;
> + u32 sysc;
>
> - sysc = serial_read_reg(p, UART_OMAP_SYSC) & 0x7;
> + sysc = omap_hwmod_read_sysc(p->oh);
> + sysc &= ~SYSC_SIDLEMODE_MASK;
> if (enable)
> - sysc |= 0x2 << 3;
> + sysc |= 0x2 << SYSC_SIDLEMODE_SHIFT;
> else
> - sysc |= 0x1 << 3;
> -
> - serial_write_reg(p, UART_OMAP_SYSC, sysc);
> + sysc |= 0x1 << SYSC_SIDLEMODE_SHIFT;
> + omap_hwmod_write_sysc(sysc, p->oh);
> }
>
> static void omap_uart_block_sleep(struct omap_uart_state *uart)
> @@ -348,7 +270,7 @@ static void omap_uart_block_sleep(struct omap_uart_state
> *uart)
>
> static void omap_uart_allow_sleep(struct omap_uart_state *uart)
> {
> - if (device_may_wakeup(&uart->pdev.dev))
> + if (device_may_wakeup(&uart->pdev->dev))
> omap_uart_enable_wakeup(uart);
> else
> omap_uart_disable_wakeup(uart);
> @@ -443,6 +365,7 @@ int omap_uart_can_sleep(void)
> * UART will not idle or sleep for its timeout period.
> *
> **/
> +/* static int first_interrupt; */
> static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
> {
> struct omap_uart_state *uart = dev_id;
> @@ -516,8 +439,8 @@ static void omap_uart_idle_init(struct omap_uart_state
> *uart)
> }
>
> uart->irqflags |= IRQF_SHARED;
> - ret = request_irq(uart->irq, omap_uart_interrupt, IRQF_SHARED,
> - "serial idle", (void *)uart);
> + ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt,
> + IRQF_SHARED, "serial idle", (void *)uart);
> WARN_ON(ret);
> }
>
> @@ -528,8 +451,11 @@ void omap_uart_enable_irqs(int enable)
>
> list_for_each_entry(uart, &uart_list, node) {
> if (enable)
> - ret = request_irq(uart->irq, omap_uart_interrupt,
> - IRQF_SHARED, "serial idle", (void *)uart);
> + ret = request_threaded_irq(uart->irq, NULL,
> + omap_uart_interrupt,
> + IRQF_SHARED,
> + "serial idle",
> + (void *)uart);
> else
> free_irq(uart->irq, (void *)uart);
> }
> @@ -539,10 +465,9 @@ static ssize_t sleep_timeout_show(struct device *dev,
> struct device_attribute *attr,
> char *buf)
> {
> - struct platform_device *pdev = container_of(dev,
> - struct platform_device, dev);
> - struct omap_uart_state *uart = container_of(pdev,
> - struct omap_uart_state, pdev);
> + struct platform_device *pdev = to_platform_device(dev);
> + struct omap_device *odev = to_omap_device(pdev);
> + struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
>
> return sprintf(buf, "%u\n", uart->timeout / HZ);
> }
> @@ -551,10 +476,9 @@ static ssize_t sleep_timeout_store(struct device *dev,
> struct device_attribute *attr,
> const char *buf, size_t n)
> {
> - struct platform_device *pdev = container_of(dev,
> - struct platform_device, dev);
> - struct omap_uart_state *uart = container_of(pdev,
> - struct omap_uart_state, pdev);
> + struct platform_device *pdev = to_platform_device(dev);
> + struct omap_device *odev = to_omap_device(pdev);
> + struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
> unsigned int value;
>
> if (sscanf(buf, "%u", &value) != 1) {
> @@ -582,87 +506,133 @@ static inline void omap_uart_idle_init(struct
> omap_uart_state *uart) {}
>
> void __init omap_serial_early_init(void)
> {
> - int i;
> - char name[16];
> -
> - /*
> - * Make sure the serial ports are muxed on at this point.
> - * You have to mux them off in device drivers later on
> - * if not needed.
> - */
> + int i = 0;
>
> - for (i = 0; i < ARRAY_SIZE(omap_uart); i++) {
> - struct omap_uart_state *uart = &omap_uart[i];
> + do {
> + char oh_name[MAX_UART_HWMOD_NAME_LEN];
> + struct omap_hwmod *oh;
> + struct omap_uart_state *uart;
>
> - uart->num = i;
> -
> - /*
> - * Module 4KB + L4 interconnect 4KB
> - * Static mapping, never released
> - */
> - uart->membase = ioremap(uart->mapbase, SZ_8K);
> - if (!uart->membase) {
> - printk(KERN_ERR "ioremap failed for uart%i\n", i + 1);
> - continue;
> - }
> -
> - sprintf(name, "uart%d_ick", i+1);
> - uart->ick = clk_get(NULL, name);
> - if (IS_ERR(uart->ick)) {
> - printk(KERN_ERR "Could not get uart%d_ick\n", i+1);
> - uart->ick = NULL;
> - }
> -
> - sprintf(name, "uart%d_fck", i+1);
> - uart->fck = clk_get(NULL, name);
> - if (IS_ERR(uart->fck)) {
> - printk(KERN_ERR "Could not get uart%d_fck\n", i+1);
> - uart->fck = NULL;
> - }
> + snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN,
> + "uart%d_hwmod", i + 1);
> + oh = omap_hwmod_lookup(oh_name);
> + if (!oh)
> + break;
>
> - /* FIXME: Remove this once the clkdev is ready */
> - if (!cpu_is_omap44xx()) {
> - if (!uart->ick || !uart->fck)
> - continue;
> - }
> + uart = kzalloc(sizeof(struct omap_uart_state), GFP_KERNEL);
> + if (WARN_ON(!uart))
> + return;
>
> + uart->oh = oh;
> + uart->num = i++;
> list_add_tail(&uart->node, &uart_list);
>
> - if (cpu_is_omap44xx())
> - uart->irq += 32;
> -
> - omap_uart_enable_clocks(uart);
> - }
> + /* NOTE: omap_hwmod_init() has not yet been called,
> + * so no hwmod functions will work yet. */
> +#ifdef CONFIG_DEBUG_LL
> + /* For DEBUG_LL, don't reset/idle the UARTs otherwise
> + * early UART access will fault. */
> + uart->oh->flags |= HWMOD_INIT_NO_IDLE;
> +#endif
> + } while(1);
> }
>
> void __init omap_serial_init(void)
> {
> - int i;
> -
> - for (i = 0; i < ARRAY_SIZE(omap_uart); i++) {
> - struct omap_uart_state *uart = &omap_uart[i];
> - struct platform_device *pdev = &uart->pdev;
> - struct device *dev = &pdev->dev;
> -#ifdef CONFIG_SERIAL_8250
> - struct plat_serial8250_port *p = dev->platform_data;
> + struct omap_uart_state *uart;
> +
> + list_for_each_entry(uart, &uart_list, node) {
> + struct omap_hwmod *oh = uart->oh;
> + struct omap_device *od;
> + void *pdata = NULL;
> + u32 pdata_size = 0;
> +#ifdef CONFIG_SERIAL_8250_CONSOLE
> + char *name = "serial8250";
> + struct plat_serial8250_port ports[2] = {
> + {},
> + {.flags = 0},
> + };
> + struct plat_serial8250_port *p = &ports[0];
> +
> + /*
> + * !! 8250 driver does not use standard IORESOURCE* It
> + * has it's own custom pdata that can be taken from
> + * the hwmod resource data. But, this needs to be
> + * done after the build.
> + *
> + * ?? does it have to be done before the register ??
> + * YES, because platform_device_data_add() copies
> + * pdata, it does not use a pointer.
> + */
> + p->flags = UPF_BOOT_AUTOCONF;
> + p->iotype = UPIO_MEM;
> + p->regshift = 2;
> + p->uartclk = OMAP24XX_BASE_BAUD * 16;
> + p->irq = oh->mpu_irqs[0].irq;
> + p->mapbase = oh->slaves[0]->addr->pa_start;
> + p->membase = oh->_rt_va;
> + p->irqflags = IRQF_SHARED;
> + p->private_data = uart;
> +
> + pdata = &ports[0];
> + pdata_size = 2 * sizeof(struct plat_serial8250_port);
> #endif
> +#ifdef CONFIG_SERIAL_OMAP_CONSOLE
> + struct uart_port_info p;
> + char *name = "omap-hsuart";
>
> - omap_uart_reset(uart);
> - omap_uart_idle_init(uart);
> + p.dma_enabled = 0;
> + p.uartclk = OMAP24XX_BASE_BAUD * 16;
>
> -#ifdef CONFIG_SERIAL_8250
> - p->membase = uart->membase;
> - p->mapbase = uart->mapbase;
> - p->irq = uart->irq;
> - p->irqflags = uart->irqflags;
> - p->private_data = uart;
> + pdata = &p;
> + pdata_size = sizeof(struct uart_port_info);
> #endif
> - if (WARN_ON(platform_device_register(pdev)))
> +
> + if (WARN_ON(!oh))
> continue;
> +
> + od = omap_device_build(name, uart->num, oh, pdata, pdata_size,
> + omap_uart_latency,
> + ARRAY_SIZE(omap_uart_latency));
> + WARN(IS_ERR(od), "Could not build omap_device for %s: %s.\n",
> + name, oh->name);
> +
> + uart->irq = oh->mpu_irqs[0].irq;
> + uart->regshift = 2;
> + uart->mapbase = oh->slaves[0]->addr->pa_start;
> + uart->membase = oh->_rt_va;
> + uart->pdev = &od->pdev;
> +
> + oh->dev_attr = uart;
> +
> +#ifdef CONFIG_DEBUG_LL
> + /*
> + * Because of earlyprintk output, UART did not get idled
> + * on init. Now that omap_device is ready, ensure full idle
> + * before doing omap_device_enable().
> + */
> + omap_hwmod_idle(uart->oh);
> +#endif
> + omap_device_enable(uart->pdev);
> + omap_uart_idle_init(uart);
> + omap_uart_reset(uart);
> + omap_hwmod_enable_wakeup(uart->oh);
> + omap_device_idle(uart->pdev);
> +
> + /*
> + * Need to block sleep long enough for interrupt driven
> + * driver to start. Console driver is in polling mode
> + * so device needs to be kept enabled while polling driver
> + * is in use.
> + */
> + uart->timeout = (30 * HZ);
> + omap_uart_block_sleep(uart);
> + uart->timeout = DEFAULT_TIMEOUT;
> +
> if ((cpu_is_omap34xx() && uart->padconf) ||
> (uart->wk_en && uart->wk_mask)) {
> - device_init_wakeup(dev, true);
> - DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
> + device_init_wakeup(&od->pdev.dev, true);
> + DEV_CREATE_FILE(&od->pdev.dev,
> &dev_attr_sleep_timeout);
> }
> }
> }
> --
> 1.6.5.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
