On Mon, Apr 19, 2010 at 12:44:22PM +0530, Manjunatha GK wrote:
> Under certain rare conditions, I2C_STAT[13].RDR bit may be set
> and the corresponding interrupt fire, even there is no data in
> the receive FIFO, or the I2C data transfer is still ongoing.
> These spurious RDR events must be ignored by the software.
> 
> This patch handles and ignores RDR spurious interrupts.
> 
> The below sequence is required in interrupt handler for
> handling this errata:
> 1. If RDR is set to 1, clear RDR
> 2. Read I2C status register and check for BusBusy bit. If BusBusy
> bit is set, skip remaining steps.
> 3. If BusBusy bit is not set, perform read operation on I2C status
> register.
> 4. If RDR is set, clear the same. Check RDR again and clear if it sets
> RDR bit again.
> 5. Perform I2C Data Read operation N number of times(where N is value
> read from the register BUFSTAT-RXSTAT bit fields).
> 
> Note : This errata is applicable for OMAP2 and OMAP3 platforms only.
> It is not applicable for OMAP4.

If people can give me a yes/no before the end of play tomorrow (ie,
2300GMT) then I will get this applied to for-linus/i2c and send it
for -rc.
 
> Signed-off-by: Manjunatha GK <manj...@ti.com>
> Cc: linux-...@vger.kernel.org
> Cc: ben-li...@fluff.org
> Cc: Kalliguddi, Hema <hem...@ti.com>
> Cc: Nishanth Menon <n...@ti.com>
> Cc: Aaro Koskinen <aaro.koski...@nokia.com>
> 
> ---
>  drivers/i2c/busses/i2c-omap.c |   28 ++++++++++++++++++++++++++++
>  1 files changed, 28 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index f2019d2..8309eac 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -796,6 +796,34 @@ complete:
>               }
>               if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
>                       u8 num_bytes = 1;
> +
> +                     /*
> +                      * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8)
> +                      * Not applicable for OMAP4.
> +                      * Under certain rare conditions, RDR could be set again
> +                      * when the bus is busy, then ignore the interrupt and
> +                      * clear the interrupt.
> +                      */
> +                     if ((stat & OMAP_I2C_STAT_RDR) && !cpu_is_omap44xx()) {
> +                             /* Step 1: If RDR is set, clear it */
> +                             omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
> +
> +                             /* Step 2: */
> +                             if(!(omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG)
> +                                                     & OMAP_I2C_STAT_BB)) {
> +                                     /* Step 3: */
> +                                     if(omap_i2c_read_reg(dev,
> +                                             OMAP_I2C_STAT_REG)
> +                                                     & OMAP_I2C_STAT_RDR) {
> +                                             omap_i2c_ack_stat(dev,
> +                                                     OMAP_I2C_STAT_RDR);
> +                                             dev_err(dev->dev,
> +                                             "RDR when the bus is busy.\n");
> +                                             continue;
> +                                     }
> +
> +                             }
> +                     }
>                       if (dev->fifo_size) {
>                               if (stat & OMAP_I2C_STAT_RRDY)
>                                       num_bytes = dev->fifo_size;
> -- 
> 1.6.0.4
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Ben (b...@fluff.org, http://www.fluff.org/)

  'a smiley only costs 4 bytes'
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to