Hi Thara,
> -----Original Message----- > From: [email protected] [mailto:linux-omap- > [email protected]] On Behalf Of Thara Gopinath > Sent: Saturday, September 25, 2010 6:21 PM > To: [email protected] > Cc: [email protected]; [email protected]; [email protected]; > [email protected]; [email protected]; Thara Gopinath > Subject: [PATCH v2 03/11] OMAP4: Add the new voltage to vsel calculation > formula > > TWL6030 the power IC used along with OMAP4 in OMAP4 SDPs, > blaze boards and panda boards has a different formula > from that of TWL4030 for voltage to vsel and > vsel to voltage calculation. This patch implements the new > formula depending on the PMIC type. > > Signed-off-by: Thara Gopinath <[email protected]> > --- > arch/arm/plat-omap/opp_twl_tps.c | 71 > ++++++++++++++++++++++++++++++++++++++ > 1 files changed, 71 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/plat-omap/opp_twl_tps.c b/arch/arm/plat- > omap/opp_twl_tps.c > index 4448fc5..358b67b 100644 > --- a/arch/arm/plat-omap/opp_twl_tps.c > +++ b/arch/arm/plat-omap/opp_twl_tps.c > @@ -15,9 +15,16 @@ > > #include <linux/module.h> > > +#include <linux/i2c/twl.h> > + > #include <plat/opp_twl_tps.h> > #include <plat/voltage.h> > > +static bool is_offset_valid; > +static u8 smps_offset; > + > +#define REG_SMPS_OFFSET 0xE0 > + > /** > * omap_twl_vsel_to_vdc - convert TWL/TPS VSEL value to microvolts DC > * @vsel: TWL/TPS VSEL value to convert > @@ -27,6 +34,38 @@ > */ > unsigned long omap_twl_vsel_to_uv(const u8 vsel) > { > + if (twl_class_is_6030()) { > + /* > + * In TWL6030 depending on the value of SMPS_OFFSET > + * efuse register the voltage range supported in > + * standard mode can be either between 0.6V - 1.3V or > + * 0.7V - 1.4V. In TWL6030 ES1.0 SMPS_OFFSET efuse > + * is programmed to all 0's where as starting from > + * TWL6030 ES1.1 the efuse is programmed to 1 > + */ > + if (!is_offset_valid) { > + twl_i2c_read_u8(TWL6030_MODULE_ID0, &smps_offset, 0xE0); > + is_offset_valid = true; > + } Is it necessary to do the i2c read each time to check the smps_offset? OR it can be done one time initially. > + > + if (smps_offset & 0x8) { > + return ((((vsel - 1) * 125) + 7000)) * 100; > + } else { > + /* > + * In case of the supported voltage range being > + * between 0.6V - 1.3V, there is not specific > + * formula for voltage to vsel conversion above > + * 1.3V. There are special hardcoded values for > + * voltages above 1.3V. Currently we are hardcodig > + * only for 1.35 V which is used for 1GH OPP for > + * OMAP4430. > + */ > + if (vsel == 0x3A) > + return 1350000; > + return ((((vsel - 1) * 125) + 6000)) * 100; > + } > + } > + > return (((vsel * 125) + 6000)) * 100; > } > > @@ -40,6 +79,38 @@ unsigned long omap_twl_vsel_to_uv(const u8 vsel) > u8 omap_twl_uv_to_vsel(unsigned long uv) > { > /* Round up to higher voltage */ > + if (twl_class_is_6030()) { > + /* > + * In TWL6030 depending on the value of SMPS_OFFSET > + * efuse register the voltage range supported in > + * standard mode can be either between 0.6V - 1.3V or > + * 0.7V - 1.4V. In TWL6030 ES1.0 SMPS_OFFSET efuse > + * is programmed to all 0's where as starting from > + * TWL6030 ES1.1 the efuse is programmed to 1 > + */ > + if (!is_offset_valid) { > + twl_i2c_read_u8(TWL6030_MODULE_ID0, &smps_offset, 0xE0); > + is_offset_valid = true; > + } Prev. comment + And this will be called each time when we do voltage scaling. - Lesly > + > + if (smps_offset & 0x8) { > + return DIV_ROUND_UP(uv - 700000, 12500) + 1; > + } else { > + /* > + * In case of the supported voltage range being > + * between 0.6V - 1.3V, there is not specific > + * formula for voltage to vsel conversion above > + * 1.3V. There are special hardcoded values for > + * voltages above 1.3V. Currently we are hardcodig > + * only for 1.35 V which is used for 1GH OPP for > + * OMAP4430. > + */ > + if (uv == 1350000) > + return 0x3A; > + return DIV_ROUND_UP(uv - 600000, 12500) + 1; > + } > + } > + > return DIV_ROUND_UP(uv - 600000, 12500); > } > > -- > 1.7.0.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to [email protected] > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
