> -----Original Message-----
> From: Hiremath, Vaibhav
> Sent: Tuesday, January 25, 2011 8:53 PM
> To: linux-omap@vger.kernel.org
> Cc: Hiremath, Vaibhav; Varadarajan, Charulatha
> Subject: [PATCH-V2] OMAP3EVM:FIX: Reset the smsc911x ethernet controller
> in board_init
>
> With addition of hwmod support to gpio, the ethernet controller
> goes undetected for OMAP35xEVM. So explicitly assert the reset signal to
> ethernet controller smsc911x -
>
> - GPIO7 (>=RevG version of EVM's)
> - GPIO64 (<=RevD version of EVM's)
>
> This patch is based on intial version from Charulatha V, reference
> to original discussion -
> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg35784.html
> Signed-off-by: Vaibhav Hiremath <hvaib...@ti.com>
> Signed-off-by: Charulatha V <ch...@ti.com>
> Tested-by: Kevin Hilman <khil...@ti.com>
> ---
> Since Kevin reported that this patch doesn't get applied cleanly,
> so I am reposting it again after making sure that it gets applied cleanly.
>
[Hiremath, Vaibhav] Oops, missed linux-arm-kernel list, adding here.
Not sure whether I need to repost keeping linux-arm-kernel?
Thanks,
Vaibhav
> arch/arm/mach-omap2/board-omap3evm.c | 39
> +++++++++++++++++++++++++++++++++-
> 1 files changed, 38 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-
> omap2/board-omap3evm.c
> index 323c380..97e0f65 100644
> --- a/arch/arm/mach-omap2/board-omap3evm.c
> +++ b/arch/arm/mach-omap2/board-omap3evm.c
> @@ -58,6 +58,13 @@
> #define OMAP3EVM_ETHR_ID_REV 0x50
> #define OMAP3EVM_ETHR_GPIO_IRQ 176
> #define OMAP3EVM_SMSC911X_CS 5
> +/*
> + * Eth Reset signal
> + * 64 = Generation 1 (<=RevD)
> + * 7 = Generation 2 (>=RevE)
> + */
> +#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64
> +#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7
>
> static u8 omap3_evm_version;
>
> @@ -124,10 +131,15 @@ static struct platform_device
> omap3evm_smsc911x_device = {
>
> static inline void __init omap3evm_init_smsc911x(void)
> {
> - int eth_cs;
> + int eth_cs, eth_rst;
> struct clk *l3ck;
> unsigned int rate;
>
> + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
> + eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST;
> + else
> + eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST;
> +
> eth_cs = OMAP3EVM_SMSC911X_CS;
>
> l3ck = clk_get(NULL, "l3_ck");
> @@ -136,6 +148,27 @@ static inline void __init
> omap3evm_init_smsc911x(void)
> else
> rate = clk_get_rate(l3ck);
>
> + /* Configure ethernet controller reset gpio */
> + if (cpu_is_omap3430()) {
> + if (gpio_request(eth_rst, "SMSC911x gpio") < 0) {
> + pr_err(KERN_ERR "Failed to request %d for smsc911x\n",
> + eth_rst);
> + return;
> + }
> +
> + if (gpio_direction_output(eth_rst, 1) < 0) {
> + pr_err(KERN_ERR "Failed to set direction of %d for" \
> + " smsc911x\n", eth_rst);
> + return;
> + }
> + /* reset pulse to ethernet controller*/
> + usleep_range(150, 220);
> + gpio_set_value(eth_rst, 0);
> + usleep_range(150, 220);
> + gpio_set_value(eth_rst, 1);
> + usleep_range(1, 2);
> + }
> +
> if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
> printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
> OMAP3EVM_ETHR_GPIO_IRQ);
> @@ -658,6 +691,10 @@ static struct omap_board_mux board_mux[] __initdata =
> {
> OMAP_PIN_OFF_WAKEUPENABLE),
> OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
> OMAP_PIN_OFF_INPUT_PULLUP |
> OMAP_PIN_OFF_OUTPUT_LOW),
> + OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
> + OMAP_PIN_OFF_NONE),
> + OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
> + OMAP_PIN_OFF_NONE),
> { .reg_offset = OMAP_MUX_TERMINATOR },
> };
> #endif
> --
> 1.6.2.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
