On Tue, 2011-05-10 at 18:55 +0530, Mayuresh Janorkar wrote:
> An on-board projector named picodlp is available for OMAP4430 SDP.
>
> Entry for this picodlp as a panel is being added in dss_devices array
> to the board file.
> It needs 4 GPIO pins for interfacing with host processor
> and these are defined and two of them are configured in board file.
> Two GPIOs power_on and display_select are configured here.
> picodlp also needs an i2c client over i2c controller-2 at address 0x1b.
>
> Signed-off-by: Mayuresh Janorkar <[email protected]>
> Signed-off-by: Mythri P K <[email protected]>
> ---
> Changes since v3:
> All GPIOs are requested here and assigned to init value.
>
> Changes since v2:
> Changed GPIO names to power_on, emu_done and pwrgood
>
> arch/arm/mach-omap2/board-4430sdp.c | 59
> +++++++++++++++++++++++++++++++++++
> 1 files changed, 59 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-4430sdp.c
> b/arch/arm/mach-omap2/board-4430sdp.c
> index 570e83f..7078037
> --- a/arch/arm/mach-omap2/board-4430sdp.c
> +++ b/arch/arm/mach-omap2/board-4430sdp.c
> @@ -38,6 +38,7 @@
> #include <plat/omap4-keypad.h>
> #include <plat/display.h>
> #include <plat/nokia-dsi-panel.h>
> +#include <plat/panel-picodlp.h>
>
> #include "mux.h"
> #include "hsmmc.h"
> @@ -52,6 +53,8 @@
> #define HDMI_GPIO_HPD 60 /* Hot plug pin for HDMI */
> #define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
> #define LCD_BL_GPIO 27 /* LCD Backlight GPIO */
> +#define OMAP4_DLP_POWER_ON_GPIO 40
> +#define OMAP4_DLP_DISPLAY_SELECT_GPIO 59
> /* PWM2 and TOGGLE3 register offsets */
> #define LED_PWM2ON 0x03
> #define LED_PWM2OFF 0x04
> @@ -812,9 +815,64 @@ static struct omap_dss_device sdp4430_hdmi_device = {
> .channel = OMAP_DSS_CHANNEL_DIGIT,
> };
>
> +static struct picodlp_panel_data sdp4430_picodlp_pdata = {
> + .picodlp_adapter_id = 2,
> + .emu_done_gpio = 44,
> + .pwrgood_gpio = 45,
> +};
It's better to define all the gpio numbers with defines, like you do for
the power_on and display_select gpios. And use the defines in the gpios
array below.
> +
> +static void sdp4430_picodlp_init(void)
> +{
> + int status;
> + struct gpio picodlp_gpios[] = {
> + {OMAP4_DLP_POWER_ON_GPIO, GPIOF_OUT_INIT_LOW,
> + "DLP POWER ON"},
> + {OMAP4_DLP_DISPLAY_SELECT_GPIO, GPIOF_OUT_INIT_LOW,
> + "DLP DISPLAY SELECT"},
> + {sdp4430_picodlp_pdata.emu_done_gpio, GPIOF_IN,
> + "DLP EMU DONE"},
> + {sdp4430_picodlp_pdata.pwrgood_gpio, GPIOF_OUT_INIT_LOW,
> + "DLP PWRGOOD"},
> + };
> +
> + status = gpio_request_array(picodlp_gpios, ARRAY_SIZE(picodlp_gpios));
> + if (status)
> + pr_err("Cannot request OMAP4_DLP_GPIOs, error %d\n", status);
> +
> + gpio_set_value(OMAP4_DLP_DISPLAY_SELECT_GPIO, 0);
> + gpio_set_value(OMAP4_DLP_POWER_ON_GPIO, 0);
> + gpio_set_value(sdp4430_picodlp_pdata.pwrgood_gpio, 1);
gpio_request_array already sets the gpio values as defined in the gpios
array.
Why do you set pwrgood to 1?
Tomi
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
