Add Kconfig entries indicating the existence of omap3evm's wlan/bt wl12xx daughter card (see http://mistralsolutions.com/component/jumi/Download_Common_Code.html?docid=298), and the exact reference clock type that the wl12xx device is hardwired to (the wl12xx driver must know this).
In addition, start using CONFIG_OMAP3EVM_MISTRAL_WL12XX in the omap3evm's board file instead of CONFIG_WL12XX_PLATFORM_DATA, because the latter only indicates that the driver is being built, and shouldn't be used to assume the existence of extension cards. Signed-off-by: Shahar Lev <[email protected]> --- arch/arm/mach-omap2/Kconfig | 23 +++++++++++++++++++++++ arch/arm/mach-omap2/board-omap3evm.c | 12 ++++++------ 2 files changed, 29 insertions(+), 6 deletions(-) diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 19d5891..8ef012d 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -342,6 +342,29 @@ config OMAP3_SDRC_AC_TIMING wish to say no. Selecting yes without understanding what is going on could result in system crashes; +config OMAP3EVM_MISTRAL_WL12XX + bool "Enable Mistral WL12XX daughter board support" + depends on MACH_OMAP3EVM + help + Support for the Mistral WL12XX daughter board. + This extension board which supports both WLAN and Bluetooth. + Specifically, for WL1271, more info can be found at + http://mistralsolutions.com/component/jumi/Download_Common_Code.html?docid=298 + +config OMAP3EVM_MISTRAL_WL12XX_REFCLOCK + int "Ref clock value" + range 0 5 + depends on OMAP3EVM_MISTRAL_WL12XX + default 2 + help + Set ref clock value for the Mistral WL12XX daughter board. + Select 0 for 19.2 MHz. + Select 1 for 26 MHz. + Select 2 for 38.4 MHz. + Select 3 for 52 MHz. + Select 4 for 38.4 MHz, XTAL. + Select 5 for 26 MHz, XTAL. + endmenu endif diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index b4d4346..23f12ff 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -318,7 +318,7 @@ static struct omap2_hsmmc_info mmc[] = { .gpio_cd = -EINVAL, .gpio_wp = 63, }, -#ifdef CONFIG_WL12XX_PLATFORM_DATA +#ifdef CONFIG_OMAP3EVM_MISTRAL_WL12XX { .name = "wl1271", .mmc = 2, @@ -506,7 +506,7 @@ static struct regulator_init_data omap3evm_vio = { .consumer_supplies = &omap3evm_vio_supply, }; -#ifdef CONFIG_WL12XX_PLATFORM_DATA +#ifdef CONFIG_OMAP3EVM_MISTRAL_WL12XX #define OMAP3EVM_WLAN_PMENA_GPIO (150) #define OMAP3EVM_WLAN_IRQ_GPIO (149) @@ -543,7 +543,7 @@ static struct platform_device omap3evm_wlan_regulator = { struct wl12xx_platform_data omap3evm_wlan_data __initdata = { .irq = OMAP_GPIO_IRQ(OMAP3EVM_WLAN_IRQ_GPIO), - .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */ + .board_ref_clock = CONFIG_OMAP3EVM_MISTRAL_WL12XX_REFCLOCK, }; #endif @@ -606,7 +606,7 @@ static struct omap_board_mux omap35x_board_mux[] __initdata = { OMAP_PIN_OFF_NONE), OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WL12XX_PLATFORM_DATA +#ifdef CONFIG_OMAP3EVM_MISTRAL_WL12XX /* WLAN IRQ - GPIO 149 */ OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), @@ -644,7 +644,7 @@ static struct omap_board_mux omap36x_board_mux[] __initdata = { OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WL12XX_PLATFORM_DATA +#ifdef CONFIG_OMAP3EVM_MISTRAL_WL12XX /* WLAN IRQ - GPIO 149 */ OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), @@ -726,7 +726,7 @@ static void __init omap3_evm_init(void) omap3evm_init_smsc911x(); omap3_evm_display_init(); -#ifdef CONFIG_WL12XX_PLATFORM_DATA +#ifdef CONFIG_OMAP3EVM_MISTRAL_WL12XX /* WL12xx WLAN Init */ if (wl12xx_set_platform_data(&omap3evm_wlan_data)) pr_err("error setting wl12xx data\n"); -- 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
