On Mon, Mar 19, 2012 at 12:18 PM, Keshava Munegowda
<[email protected]> wrote:
> From: Keshava Munegowda <[email protected]>
>
> The platform driver for the TLL component of the OMAP USB host controller
> is implemented. Depending on the TLL hardware revision , the TLL channels
> are configured. The USB HS core driver uses this driver through exported
> APIs from the TLL platform driver.
> usb_tll_enable and usb_tll_disble are the exported APIs of the USB TLL
> platform driver.
>
> Signed-off-by: Keshava Munegowda <[email protected]>
> Reviewed-by: Partha Basak <[email protected]>
> ---
> arch/arm/plat-omap/include/plat/usb.h | 8 +
> drivers/mfd/Kconfig | 2 +-
> drivers/mfd/Makefile | 2 +-
> drivers/mfd/omap-usb-tll.c | 463
> +++++++++++++++++++++++++++++++++
> 4 files changed, 473 insertions(+), 2 deletions(-)
> create mode 100644 drivers/mfd/omap-usb-tll.c
>
> diff --git a/arch/arm/plat-omap/include/plat/usb.h
> b/arch/arm/plat-omap/include/plat/usb.h
> index dc864b5..eb1e47d 100644
> --- a/arch/arm/plat-omap/include/plat/usb.h
> +++ b/arch/arm/plat-omap/include/plat/usb.h
> @@ -61,6 +61,10 @@ struct usbhs_omap_platform_data {
> struct ehci_hcd_omap_platform_data *ehci_data;
> struct ohci_hcd_omap_platform_data *ohci_data;
> };
> +
> +struct usbtll_omap_platform_data {
> + enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
> +};
> /*-------------------------------------------------------------------------*/
>
> #define OMAP1_OTG_BASE 0xfffb0400
> @@ -105,6 +109,10 @@ extern int omap4430_phy_set_clk(struct device *dev, int
> on);
> extern int omap4430_phy_init(struct device *dev);
> extern int omap4430_phy_exit(struct device *dev);
> extern int omap4430_phy_suspend(struct device *dev, int suspend);
> +
> +extern int omap_tll_enable(void);
> +extern int omap_tll_disable(void);
> +
> #endif
>
> extern void am35x_musb_reset(void);
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index f147395..5f75ad4 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -772,7 +772,7 @@ config MFD_WL1273_CORE
> audio codec.
>
> config MFD_OMAP_USB_HOST
> - bool "Support OMAP USBHS core driver"
> + bool "Support OMAP USBHS core and TLL driver"
> depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3
> default y
> help
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index b953bab..4b3a8e0 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -105,7 +105,7 @@ obj-$(CONFIG_MFD_TPS6586X) += tps6586x.o
> obj-$(CONFIG_MFD_VX855) += vx855.o
> obj-$(CONFIG_MFD_WL1273_CORE) += wl1273-core.o
> obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
> -obj-$(CONFIG_MFD_OMAP_USB_HOST) += omap-usb-host.o
> +obj-$(CONFIG_MFD_OMAP_USB_HOST) += omap-usb-host.o omap-usb-tll.o
> obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o
> obj-$(CONFIG_MFD_PM8XXX_IRQ) += pm8xxx-irq.o
> obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
> diff --git a/drivers/mfd/omap-usb-tll.c b/drivers/mfd/omap-usb-tll.c
> new file mode 100644
> index 0000000..3da468a
> --- /dev/null
> +++ b/drivers/mfd/omap-usb-tll.c
> @@ -0,0 +1,463 @@
> +/**
> + * omap-usb-tll.c - The USB TLL driver for OMAP EHCI & OHCI
> + *
> + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com
> + * Author: Keshava Munegowda <[email protected]>
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 of
> + * the License as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/types.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/err.h>
> +#include <plat/usb.h>
> +#include <linux/pm_runtime.h>
> +
> +#define USBTLL_DRIVER_NAME "usbhs_tll"
> +
> +/* TLL Register Set */
> +#define OMAP_USBTLL_REVISION (0x00)
> +#define OMAP_USBTLL_SYSCONFIG (0x10)
> +#define OMAP_USBTLL_SYSCONFIG_CACTIVITY (1 << 8)
> +#define OMAP_USBTLL_SYSCONFIG_SIDLEMODE (1 << 3)
> +#define OMAP_USBTLL_SYSCONFIG_ENAWAKEUP (1 << 2)
> +#define OMAP_USBTLL_SYSCONFIG_SOFTRESET (1 << 1)
> +#define OMAP_USBTLL_SYSCONFIG_AUTOIDLE (1 << 0)
> +
> +#define OMAP_USBTLL_SYSSTATUS (0x14)
> +#define OMAP_USBTLL_SYSSTATUS_RESETDONE (1 << 0)
> +
> +#define OMAP_USBTLL_IRQSTATUS (0x18)
> +#define OMAP_USBTLL_IRQENABLE (0x1C)
> +
> +#define OMAP_TLL_SHARED_CONF (0x30)
> +#define OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN (1 << 6)
> +#define OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN (1 << 5)
> +#define OMAP_TLL_SHARED_CONF_USB_DIVRATION (1 << 2)
> +#define OMAP_TLL_SHARED_CONF_FCLK_REQ (1 << 1)
> +#define OMAP_TLL_SHARED_CONF_FCLK_IS_ON (1 << 0)
> +
> +#define OMAP_TLL_CHANNEL_CONF(num) (0x040 +
> 0x004 * num)
> +#define OMAP_TLL_CHANNEL_CONF_FSLSMODE_SHIFT 24
> +#define OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF (1 << 11)
> +#define OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE (1 << 10)
> +#define OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE (1 << 9)
> +#define OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE (1 << 8)
> +#define OMAP_TLL_CHANNEL_CONF_CHANMODE_FSLS (1 << 1)
> +#define OMAP_TLL_CHANNEL_CONF_CHANEN (1 << 0)
> +
> +#define OMAP_TLL_FSLSMODE_6PIN_PHY_DAT_SE0 0x0
> +#define OMAP_TLL_FSLSMODE_6PIN_PHY_DP_DM 0x1
> +#define OMAP_TLL_FSLSMODE_3PIN_PHY 0x2
> +#define OMAP_TLL_FSLSMODE_4PIN_PHY 0x3
> +#define OMAP_TLL_FSLSMODE_6PIN_TLL_DAT_SE0 0x4
> +#define OMAP_TLL_FSLSMODE_6PIN_TLL_DP_DM 0x5
> +#define OMAP_TLL_FSLSMODE_3PIN_TLL 0x6
> +#define OMAP_TLL_FSLSMODE_4PIN_TLL 0x7
> +#define OMAP_TLL_FSLSMODE_2PIN_TLL_DAT_SE0 0xA
> +#define OMAP_TLL_FSLSMODE_2PIN_DAT_DP_DM 0xB
> +
> +#define OMAP_TLL_ULPI_FUNCTION_CTRL(num) (0x804 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_INTERFACE_CTRL(num) (0x807 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_OTG_CTRL(num) (0x80A +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_INT_EN_RISE(num) (0x80D +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_INT_EN_FALL(num) (0x810 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_INT_STATUS(num) (0x813 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_INT_LATCH(num) (0x814 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_DEBUG(num) (0x815 +
> 0x100 * num)
> +#define OMAP_TLL_ULPI_SCRATCH_REGISTER(num) (0x816 +
> 0x100 * num)
> +
> +#define OMAP_REV2_TLL_CHANNEL_COUNT 2
> +#define OMAP_TLL_CHANNEL_COUNT 3
> +#define OMAP_TLL_CHANNEL_1_EN_MASK (1 << 0)
> +#define OMAP_TLL_CHANNEL_2_EN_MASK (1 << 1)
> +#define OMAP_TLL_CHANNEL_3_EN_MASK (1 << 2)
> +
> +/* Values of USBTLL_REVISION - Note: these are not given in the TRM */
> +#define OMAP_USBTLL_REV1 0x00000015 /* OMAP3 */
> +#define OMAP_USBTLL_REV2 0x00000004 /* OMAP4 */
> +
> +#define is_ehci_tll_mode(x) (x == OMAP_EHCI_PORT_MODE_TLL)
> +
> +struct usbtll_omap {
> + struct clk *usbtll_p1_fck;
> + struct clk *usbtll_p2_fck;
> + struct usbtll_omap_platform_data platdata;
> + spinlock_t lock;
> +};
> +
> +/*-------------------------------------------------------------------------*/
> +
> +const char usbtll_driver_name[] = USBTLL_DRIVER_NAME;
> +struct platform_device *tll_pdev;
> +
> +/*-------------------------------------------------------------------------*/
> +
> +static inline void usbtll_write(void __iomem *base, u32 reg, u32 val)
> +{
> + __raw_writel(val, base + reg);
> +}
> +
> +static inline u32 usbtll_read(void __iomem *base, u32 reg)
> +{
> + return __raw_readl(base + reg);
> +}
> +
> +static inline void usbtll_writeb(void __iomem *base, u8 reg, u8 val)
> +{
> + __raw_writeb(val, base + reg);
> +}
> +
> +static inline u8 usbtll_readb(void __iomem *base, u8 reg)
> +{
> + return __raw_readb(base + reg);
> +}
> +
> +/*-------------------------------------------------------------------------*/
> +
> +static bool is_ohci_port(enum usbhs_omap_port_mode pmode)
> +{
> + switch (pmode) {
> + case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
> + case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
> + case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
> + case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
> + case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
> + case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
> + case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
> + case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
> + case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
> + case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
> + return true;
> +
> + default:
> + return false;
> + }
> +}
> +
> +/*
> + * convert the port-mode enum to a value we can use in the FSLSMODE
> + * field of USBTLL_CHANNEL_CONF
> + */
> +static unsigned ohci_omap3_fslsmode(enum usbhs_omap_port_mode mode)
> +{
> + switch (mode) {
> + case OMAP_USBHS_PORT_MODE_UNUSED:
> + case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
> + return OMAP_TLL_FSLSMODE_6PIN_PHY_DAT_SE0;
> +
> + case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
> + return OMAP_TLL_FSLSMODE_6PIN_PHY_DP_DM;
> +
> + case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
> + return OMAP_TLL_FSLSMODE_3PIN_PHY;
> +
> + case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
> + return OMAP_TLL_FSLSMODE_4PIN_PHY;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
> + return OMAP_TLL_FSLSMODE_6PIN_TLL_DAT_SE0;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
> + return OMAP_TLL_FSLSMODE_6PIN_TLL_DP_DM;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
> + return OMAP_TLL_FSLSMODE_3PIN_TLL;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
> + return OMAP_TLL_FSLSMODE_4PIN_TLL;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
> + return OMAP_TLL_FSLSMODE_2PIN_TLL_DAT_SE0;
> +
> + case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
> + return OMAP_TLL_FSLSMODE_2PIN_DAT_DP_DM;
> + default:
> + pr_warning("Invalid port mode, using default\n");
> + return OMAP_TLL_FSLSMODE_6PIN_PHY_DAT_SE0;
> + }
> +}
> +
> +/**
> + * usbtll_omap_probe - initialize TI-based HCDs
> + *
> + * Allocates basic resources for this USB host controller.
> + */
> +static int __devinit usbtll_omap_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct usbtll_omap_platform_data *pdata = dev->platform_data;
> + void __iomem *base;
> + struct resource *res;
> + struct usbtll_omap *tll;
> + unsigned reg;
> + unsigned long flags;
> + int ret = 0;
> + int i, ver, count;
> +
> + dev_dbg(dev, "starting TI HSUSB TLL Controller\n");
> +
> + tll = kzalloc(sizeof(struct usbtll_omap), GFP_KERNEL);
> + if (!tll) {
> + dev_err(dev, "Memory allocation failed\n");
> + ret = -ENOMEM;
> + goto end;
> + }
> +
> + spin_lock_init(&tll->lock);
> +
> + for (i = 0; i < OMAP3_HS_USB_PORTS; i++)
> + tll->platdata.port_mode[i] = pdata->port_mode[i];
> +
> + tll->usbtll_p1_fck = clk_get(dev, "usb_tll_hs_usb_ch0_clk");
> + if (IS_ERR(tll->usbtll_p1_fck)) {
> + ret = PTR_ERR(tll->usbtll_p1_fck);
> + dev_err(dev, "usbtll_p1_fck failed error:%d\n", ret);
> + goto err_tll;
> + }
> +
> + tll->usbtll_p2_fck = clk_get(dev, "usb_tll_hs_usb_ch1_clk");
> + if (IS_ERR(tll->usbtll_p2_fck)) {
> + ret = PTR_ERR(tll->usbtll_p2_fck);
> + dev_err(dev, "usbtll_p2_fck failed error:%d\n", ret);
> + goto err_usbtll_p1_fck;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + dev_err(dev, "usb tll get resource failed\n");
> + ret = -ENODEV;
> + goto err_usbtll_p2_fck;
> + }
> +
> + base = ioremap(res->start, resource_size(res));
> + if (!base) {
> + dev_err(dev, "TLL ioremap failed\n");
> + ret = -ENOMEM;
> + goto err_usbtll_p2_fck;
> + }
> +
> + platform_set_drvdata(pdev, tll);
> + pm_runtime_enable(dev);
> + pm_runtime_get_sync(dev);
> +
> + spin_lock_irqsave(&tll->lock, flags);
> +
> + ver = usbtll_read(base, OMAP_USBTLL_REVISION);
> + if (ver == OMAP_USBTLL_REV1)
> + count = OMAP_TLL_CHANNEL_COUNT;
> + else if (ver == OMAP_USBTLL_REV2)
> + count = OMAP_REV2_TLL_CHANNEL_COUNT;
> + else {
> + dev_err(dev, "TLL version failed\n");
> + ret = -ENODEV;
> + goto err_ioremap;
> + }
> +
> + if (is_ehci_tll_mode(pdata->port_mode[0]) ||
> + is_ehci_tll_mode(pdata->port_mode[1]) ||
> + is_ehci_tll_mode(pdata->port_mode[2]) ||
> + (is_ohci_port(pdata->port_mode[0])) ||
> + (is_ohci_port(pdata->port_mode[1])) ||
> + (is_ohci_port(pdata->port_mode[2]))) {
> +
> + /* Program Common TLL register */
> + reg = usbtll_read(base, OMAP_TLL_SHARED_CONF);
> + reg |= (OMAP_TLL_SHARED_CONF_FCLK_IS_ON
> + | OMAP_TLL_SHARED_CONF_USB_DIVRATION);
> + reg &= ~OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN;
> + reg &= ~OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN;
> +
> + usbtll_write(base, OMAP_TLL_SHARED_CONF, reg);
> +
> + /* Enable channels now */
> + for (i = 0; i < count; i++) {
> + reg = usbtll_read(base, OMAP_TLL_CHANNEL_CONF(i));
> +
> + if (is_ohci_port(pdata->port_mode[i])) {
> + reg |=
> ohci_omap3_fslsmode(pdata->port_mode[i])
> + << OMAP_TLL_CHANNEL_CONF_FSLSMODE_SHIFT;
> + reg |= OMAP_TLL_CHANNEL_CONF_CHANMODE_FSLS;
> + } else
> + if (pdata->port_mode[i] == OMAP_EHCI_PORT_MODE_TLL) {
> +
> + /*
> + * Disable AutoIdle, BitStuffing
> + * and use SDR Mode
> + */
> + reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
> + | OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
> + | OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
> + } else
> + continue;
> +
> + reg |= OMAP_TLL_CHANNEL_CONF_CHANEN;
> + usbtll_write(base, OMAP_TLL_CHANNEL_CONF(i), reg);
> +
> + usbtll_writeb(base,
> + OMAP_TLL_ULPI_SCRATCH_REGISTER(i), 0xbe);
> + }
> + }
> +
> +err_ioremap:
> + spin_unlock_irqrestore(&tll->lock, flags);
> + iounmap(base);
> + pm_runtime_put_sync(dev);
> + tll_pdev = pdev;
> + if (!ret)
> + goto end;
> + pm_runtime_disable(dev);
> +
> +err_usbtll_p2_fck:
> + clk_put(tll->usbtll_p2_fck);
> +
> +err_usbtll_p1_fck:
> + clk_put(tll->usbtll_p1_fck);
> +
> +err_tll:
> + kfree(tll);
> +
> +end:
> + return ret;
> +}
> +
> +/**
> + * usbtll_omap_remove - shutdown processing for UHH & TLL HCDs
> + * @pdev: USB Host Controller being removed
> + *
> + * Reverses the effect of usbtll_omap_probe().
> + */
> +static int __devexit usbtll_omap_remove(struct platform_device *pdev)
> +{
> + struct usbtll_omap *tll = platform_get_drvdata(pdev);
> +
> + clk_put(tll->usbtll_p2_fck);
> + clk_put(tll->usbtll_p1_fck);
> + pm_runtime_disable(&pdev->dev);
> + kfree(tll);
> + return 0;
> +}
> +
> +static int usbtll_runtime_resume(struct device *dev)
> +{
> + struct usbtll_omap *tll = dev_get_drvdata(dev);
> + struct usbtll_omap_platform_data *pdata = &tll->platdata;
> + unsigned long flags;
> +
> + dev_dbg(dev, "usbtll_runtime_resume\n");
> +
> + if (!pdata) {
> + dev_dbg(dev, "missing platform_data\n");
> + return -ENODEV;
> + }
> +
> + spin_lock_irqsave(&tll->lock, flags);
> +
> + if (is_ehci_tll_mode(pdata->port_mode[0]))
> + clk_enable(tll->usbtll_p1_fck);
> +
> + if (is_ehci_tll_mode(pdata->port_mode[1]))
> + clk_enable(tll->usbtll_p2_fck);
> +
> + spin_unlock_irqrestore(&tll->lock, flags);
> +
> + return 0;
> +}
> +
> +static int usbtll_runtime_suspend(struct device *dev)
> +{
> + struct usbtll_omap *tll = dev_get_drvdata(dev);
> + struct usbtll_omap_platform_data *pdata = &tll->platdata;
> + unsigned long flags;
> +
> + dev_dbg(dev, "usbtll_runtime_suspend\n");
> +
> + if (!pdata) {
> + dev_dbg(dev, "missing platform_data\n");
> + return -ENODEV;
> + }
> +
> + spin_lock_irqsave(&tll->lock, flags);
> +
> + if (is_ehci_tll_mode(pdata->port_mode[0]))
> + clk_disable(tll->usbtll_p1_fck);
> +
> + if (is_ehci_tll_mode(pdata->port_mode[1]))
> + clk_disable(tll->usbtll_p2_fck);
> +
> + spin_unlock_irqrestore(&tll->lock, flags);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops usbtllomap_dev_pm_ops = {
> + .runtime_suspend = usbtll_runtime_suspend,
> + .runtime_resume = usbtll_runtime_resume,
> +};
> +
> +static struct platform_driver usbtll_omap_driver = {
> + .driver = {
> + .name = (char *)usbtll_driver_name,
> + .owner = THIS_MODULE,
> + .pm = &usbtllomap_dev_pm_ops,
> + },
> + .remove = __exit_p(usbtll_omap_remove),
> +};
> +
> +int omap_tll_enable(void)
> +{
> + if (!tll_pdev) {
> + dev_dbg(&tll_pdev->dev, "missing platform_data\n");
> + return -ENODEV;
> + }
> + return pm_runtime_get_sync(&tll_pdev->dev);
> +}
> +EXPORT_SYMBOL_GPL(omap_tll_enable);
> +
> +int omap_tll_disable(void)
> +{
> + if (!tll_pdev) {
> + dev_dbg(&tll_pdev->dev, "missing platform_data\n");
> + return -ENODEV;
> + }
> + return pm_runtime_put_sync(&tll_pdev->dev);
> +}
> +EXPORT_SYMBOL_GPL(omap_tll_disable);
> +
> +MODULE_AUTHOR("Keshava Munegowda <[email protected]>");
> +MODULE_ALIAS("platform:" USBHS_DRIVER_NAME);
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("usb tll driver for TI OMAP EHCI and OHCI controllers");
> +
> +static int __init omap_usbtll_drvinit(void)
> +{
> + return platform_driver_probe(&usbtll_omap_driver, usbtll_omap_probe);
> +}
> +
> +/*
> + * init before usbhs core driver;
> + * The usbtll driver should be initialized before
> + * the usbhs core driver probe function is called.
> + */
> +fs_initcall(omap_usbtll_drvinit);
Hi Felipe
do you have any comment here?
The TLL driver uses fs_initcall
and the UHH uses fs_initcall_sync
Intension of using this is , TLL driver should be initialized before UHH.
regards
keshava
> +
> +static void __exit omap_usbtll_drvexit(void)
> +{
> + platform_driver_unregister(&usbtll_omap_driver);
> +}
> +module_exit(omap_usbtll_drvexit);
> --
> 1.6.0.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
