Add device nodes for the HS USB Host port 1, USB PHY and its required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <[email protected]> --- arch/arm/boot/dts/omap3-igep.dtsi | 22 ++++++++++++++++++++++ arch/arm/boot/dts/omap3-igep0020.dts | 25 +++++++++++++++++++++++++ 2 files changed, 47 insertions(+) diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 0f92224..ec2ecd2 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -27,6 +27,11 @@ }; &omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_pins + >; + uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < 0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ @@ -78,6 +83,23 @@ >; }; + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ + 0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ + 0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */ + 0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */ + 0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */ + 0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */ + 0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */ + 0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */ + 0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */ + 0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */ + 0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */ + 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ + >; + }; + leds_pins: pinmux_leds_pins { }; }; diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 903e944..180b186 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -55,6 +55,23 @@ regulator-name = "vdd33a"; regulator-always-on; }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */ + vcc-supply = <&hsusb1_power>; + }; }; &leds_pins { @@ -173,3 +190,11 @@ mode = <3>; power = <50>; }; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; -- 1.8.4.rc3 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
