On 10/25/2013 10:57 AM, Tero Kristo wrote:
> This patch adds support for TI specific gate clocks. These behave as basic
> gate-clock, but have different ops / hw-ops for controlling the actual
> gate, for example waiting until the clock is ready. Several sub-types
> are supported:
> - ti,gate-clock: basic gate clock with default ops/hwops
> - ti,clkdm-gate-clock: clockdomain level gate control
> - ti,dss-gate-clock: gate clock with DSS specific hardware handling
> - ti,am35xx-gate-clock: gate clock with AM35xx specific hardware handling
> - ti,hsdiv-gate-clock: gate clock with OMAP36xx hardware errata handling
>
> Signed-off-by: Tero Kristo <[email protected]>
> ---
> .../devicetree/bindings/clock/ti/gate.txt | 77 ++++++
> arch/arm/mach-omap2/clock.h | 29 ---
> drivers/clk/ti/Makefile | 2 +-
> drivers/clk/ti/gate.c | 258
> ++++++++++++++++++++
> include/linux/clk/ti.h | 36 +++
> 5 files changed, 372 insertions(+), 30 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/clock/ti/gate.txt
> create mode 100644 drivers/clk/ti/gate.c
>
> diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt
> b/Documentation/devicetree/bindings/clock/ti/gate.txt
> new file mode 100644
> index 0000000..18c4d86
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/ti/gate.txt
> @@ -0,0 +1,77 @@
> +Binding for Texas Instruments gate clock.
> +
> +Binding status: Unstable - ABI compatibility may be broken in the future
> +
> +This binding uses the common clock binding[1]. This clock is
> +quite much similar to the basic gate-clock [2], however,
> +it supports a number of additional features. If no register
> +is provided for this clock, the code assumes that a clockdomain
> +will be controlled instead and the corresponding hw-ops for
> +that is used.
> +
> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
> +[2] Documentation/devicetree/bindings/clock/gate-clock.txt
> +[3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt
i think you may want to sequence patch #12 before this if you would
like to refer to this.
> +
> +Required properties:
> +- compatible : shall be one of:
> + "ti,gate-clock" - basic gate clock
> + "ti,wait-gate-clock" - gate clock which waits until clock is active before
> + returning from clk_enable()
an example will be nice for this.
[...]
> diff --git a/drivers/clk/ti/gate.c b/drivers/clk/ti/gate.c
> new file mode 100644
> index 0000000..1a201f8
> --- /dev/null
> +++ b/drivers/clk/ti/gate.c
[...]
> +/**
> + * omap36xx_gate_clk_enable_with_hsdiv_restore - enable clocks suffering
> + * from HSDivider PWRDN problem Implements Errata ID: i556.
> + * @clk: DPLL output struct clk
> + *
> + * 3630 only: dpll3_m3_ck, dpll4_m2_ck, dpll4_m3_ck, dpll4_m4_ck,
> + * dpll4_m5_ck & dpll4_m6_ck dividers gets loaded with reset
> + * valueafter their respective PWRDN bits are set. Any dummy write
> + * (Any other value different from the Read value) to the
> + * corresponding CM_CLKSEL register will refresh the dividers.
> + */
> +static int omap36xx_gate_clk_enable_with_hsdiv_restore(struct clk_hw *clk)
> +{
> + struct clk_divider *parent;
> + struct clk_hw *parent_hw;
> + u32 dummy_v, orig_v;
> + int ret;
> +
> + /* Clear PWRDN bit of HSDIVIDER */
> + ret = omap2_dflt_clk_enable(clk);
> +
> + /* Parent is the x2 node, get parent of parent for the m2 div */
> + parent_hw = __clk_get_hw(__clk_get_parent(__clk_get_parent(clk->clk)));
> + parent = to_clk_divider(parent_hw);
> +
> + /* Restore the dividers */
> + if (!ret) {
> + orig_v = __raw_readl(parent->reg);
> + dummy_v = orig_v;
> +
> + /* Write any other value different from the Read value */
> + dummy_v ^= (1 << parent->shift);
> + __raw_writel(dummy_v, parent->reg);
> +
> + /* Write the original divider */
> + __raw_writel(orig_v, parent->reg);
i think we already did state that these need to be regmap_updatebits..
> + }
> +
> + return ret;
> +}
> +
> +static int __init _of_ti_gate_clk_setup(struct device_node *node,
> + const struct clk_ops *ops,
> + const struct clk_hw_omap_ops *hw_ops,
> + struct regmap *regmap)
> +{
> + struct clk *clk;
> + struct clk_init_data init = { NULL };
> + struct clk_hw_omap *clk_hw;
> + const char *clk_name = node->name;
> + const char *parent_name;
> + u32 val;
> +
> + clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
> + if (!clk_hw) {
> + pr_err("%s: could not allocate clk_hw_omap\n", __func__);
> + return -ENOMEM;
> + }
> +
> + clk_hw->hw.init = &init;
> +
> + of_property_read_string(node, "clock-output-names", &clk_name);
> +
> + init.name = clk_name;
> + init.ops = ops;
> +
> + if (!of_property_read_u32(node, "reg", &val))
> + clk_hw->enable_reg = (void *)val;
seems reg is a mandatory as per bindings for everything other than
ti,clkdm-gate-clock.. no error handling?
> +
> + clk_hw->regmap = regmap;
> +
> + if (!of_property_read_u32(node, "ti,bit-shift", &val))
> + clk_hw->enable_bit = val;
Again -> bindings state this is mandatory for non ti,clkdm-gate-clock
clocks. no error handling?
> + clk_hw->ops = hw_ops;
> +
> + parent_name = of_clk_get_parent_name(node, 0);
> + init.parent_names = &parent_name;
> + init.num_parents = 1;
error checks for parent clk which seems to be mandatory?
> +
> + if (of_property_read_bool(node, "ti,set-rate-parent"))
> + init.flags |= CLK_SET_RATE_PARENT;
> +
> + if (of_property_read_bool(node, "ti,set-bit-to-disable"))
> + clk_hw->flags |= INVERT_ENABLE;
> +
> + clk = clk_register(NULL, &clk_hw->hw);
> +
> + if (!IS_ERR(clk)) {
> + of_clk_add_provider(node, of_clk_src_simple_get, clk);
> + return 0;
> + }
> +
free(clk_hw)?
> + return PTR_ERR(clk);
> +}
> +
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
