This is a normal driver/controller initialization procedure. Disregard the exclamation :)
________________________________ From: [email protected] on behalf of Giulio Sent: Wed 3/17/2010 10:57 AM To: linux-poweredge-Lists Subject: PERC H200: boot message "mpt2sas0: sending diag reset !!" PET310, CentOS5.4, mpt2sas 02.00.02.00 At every boot I get some messages marked with multiple exclamation points. mpt2sas0: sending diag reset !! mpt2sas0: diag reset: SUCCESS mpt2sas0: sending port enable !! Are these normal or should I contact Dell support? Thanks ============= mpt2sas version 02.00.02.00 loaded scsi0 : Fusion MPT SAS Host ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:03:00.0 to 64 mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3097884 kB) mpt2sas0: PCI-MSI-X enabled: IRQ 50 mpt2sas0: iomem(0xdf2b0000), mapped(0xf88c0000), size(65536) mpt2sas0: ioport(0xfc00), size(256) mpt2sas0: sending diag reset !! mpt2sas0: diag reset: SUCCESS mpt2sas0: Allocated physical memory: size(750 kB) mpt2sas0: Current Controller Queue Depth(490), Max Controller Queue Depth(3439) mpt2sas0: Scatter Gather Elements per IO(128) mpt2sas0: LSISAS2008: FWVersion(02.15.57.00), ChipRevision(0x02), BiosVersion(07.01.04.00) mpt2sas0: Dell PERC H200 Adapter: Vendor(0x1000), Device(0x0072), SSVID(0x1028), SSDID(0x1F1D) mpt2sas0: Protocol=(Initiator,Target), Capabilities=(Raid,TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) mpt2sas0: sending port enable !! mpt2sas0: host_add: handle(0x0001), sas_addr(0x5a4badb013972700), phys(8) mpt2sas0: port enable: SUCCESS Vendor: Dell Model: Virtual Disk Rev: 1028 Type: Direct-Access ANSI SCSI revision: 06 scsi 0:1:0:0: RAID1: handle(0x004f), wwid(0x009029b53f8f2a7b), pd_count(2), type (SATA) scsi 0:1:0:0: qdepth(128), tagged(1), simple(1), ordered(0), scsi_level(7), cmd_que(1) SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write through SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write through sda: sda1 sda2 sda3 sda4 sd 0:1:0:0: Attached scsi disk sda Vendor: ATA Model: WDC WD2502ABYS-1 Rev: 3B04 Type: Direct-Access ANSI SCSI revision: 05 scsi 0:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), device_name(0x4ee15001e9710289) scsi 0:0:0:0: SATA: enclosure_logical_id(0x5a4badb013972700), slot(1) scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) scsi 0:0:0:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(6), cmd_que(1) Vendor: ATA Model: WDC WD2502ABYS-1 Rev: 3B04 Type: Direct-Access ANSI SCSI revision: 05 scsi 0:0:1:0: SATA: handle(0x000b), sas_addr(0x4433221107000000), device_name(0x4ee150019df6028a) scsi 0:0:1:0: SATA: enclosure_logical_id(0x5a4badb013972700), slot(0) scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) scsi 0:0:1:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(6), cmd_que(1) Thanks -- [email protected] _______________________________________________ Linux-PowerEdge mailing list [email protected] https://lists.us.dell.com/mailman/listinfo/linux-poweredge Please read the FAQ at http://lists.us.dell.com/faq _______________________________________________ Linux-PowerEdge mailing list [email protected] https://lists.us.dell.com/mailman/listinfo/linux-poweredge Please read the FAQ at http://lists.us.dell.com/faq
