Wayne, I tried installing the RPMs for OMSA 5.5 as you suggested. It seems that they too are doing some sort of system check. "srvadmin-omilcore" installs fine. But, the remaining packages fail to install with the error:
srvadmin-syscheck: This RPM is not supported on this system (sysid=009B) error: %pre(srvadmin-syscheck-5.5.0-364.i386) scriptlet failed, exit status 1 error: install: %pre scriptlet failed (2), skipping srvadmin-syscheck-5.5.0-364 I've tried adding "Tikanga" to /etc/redhat-release , however it does not help. Does anybody know of a way to get this to install? Thanks again in advance! -- Chris > In OM 6.1 we removed many of the install blockages. In the past, the > installation scripts would prevent installation on any unsupported > distribution or version. In 6.1, these checks have been replaced with > standard RPM dependency checks. At run time, there are a few checks within > our processes to ensure that we are running on Dell hardware that is not too > old. Note that the ability to install on a version/distribution does not > imply that it is officially supported or that it will work. > > The net of this is that you should be able to install OMSA on SELinlux if > the RPMs we are dependent on are installed. I believe there is a good > chance OMSA will work, but no guarantees. Try it and see. > > Wayne Weilnau > Systems Management Technologist > Dell | OpenManage Software Development > > Please consider the environment before printing this email. > > Confidentiality Notice | This e-mail message, including any attachments, is > for the sole use of the intended recipient(s) and may contain confidential > or proprietary information. Any unauthorized review, use, disclosure or > distribution is prohibited. If you are not the intended recipient, > immediately contact the sender by reply e-mail and destroy all copies of the > original message. > > -----Original Message----- > From: linux-poweredge-bounces-Lists On Behalf Of Liberty Young > Sent: Wednesday, September 22, 2010 11:59 AM > To: Chris Szilagyi > Cc: linux-poweredge-Lists > Subject: Re: Issues with OpenManage + CentOs 5.4 > > what about SELinux? Is it enabled? > > On Thu, Sep 16, 2010 at 8:29 PM, Chris Szilagyi <[email protected]> > wrote: >> Hello: >> >> I recently set up a PowerEdge 2400 server running CentOS 5.4. Â I'm trying >> to >> get OpenManage 4.5 installed (last version that I could find, that >> supports >> the PowerEdge 2400). Â I installed everything using the supplied scripts, >> however when I try to start the services with "srvadmin-services.sh >> start", >> I get the following: >> >> Starting Systems Management Device Drivers: >> Starting dcdbas device driver: Â Â Â Â Â Â Â Â Â Â Â Â Â Â [ >> Â OK Â ] >> Starting Systems Management Data Engine: >> Starting dcstor32d: Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â >> Â Â [ Â OK Â ] >> Starting dcevt32d: Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â >> Â Â [ Â OK Â ] >> Starting OM Common Services: Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â >> [ Â OK Â ] >> invcol Error: extract(): Unable to create temporary files. Please ensure >> that there is enough space in the >> tmp folder. >> Starting Secure Port Server: Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â >> [ Â OK Â ] >> >> The disk has over 7 GB of free space, and permissions look OK on /tmp. >> Â Has >> anybody seen this problem or know of a solution? Â So far I'm stumped. >> >> Thank you !! >> -- >> Chris >> _______________________________________________ Linux-PowerEdge mailing list [email protected] https://lists.us.dell.com/mailman/listinfo/linux-poweredge Please read the FAQ at http://lists.us.dell.com/faq
