Hi You must flash the card with PXE boot image from intel with intel tool, check on intel website.
George Machitidze ICT Consultant On Dec 20, 2016 10:26 AM, "Max Vernimmen" <[email protected]> wrote: > Hi Mike, > > > > It's been a few years since I set up the same card and I had the same > problem you're having. If my memory serves my correctly there is a > 'special' intel program that you can use to enable pxe for the card. It's > from intel, not from dell. Unfortunately I don't remember where I found it > or how to use it. > > I hope that helps. > > > > Best regards, > > > > > > Max > > > > *From: *<[email protected]> on behalf of "Hanby, Mike" < > [email protected]> > *Date: *Tuesday, 20 December 2016 at 04:01 > *To: *"[email protected]" <[email protected]. > dell.com> > *Subject: *[Linux-PowerEdge] Dell onboard Intel X520 not listed in PXE > boot list on R730 > > > > Howdy, I have one of these (Intel X520) 10GBit onboard and can't for the > life of me find a way to get it enabled as a PXE boot device (the lspci > output for the NIC is at the end of the email) The X520 provides 2 x 1GbitE > ports and 2 x 10GbitE ports on the motherboard. > > > > According to the iDRAC view of the network interface, it supports PXE > "Supported Boot Protocol ---- iSCSI, FCoE, PXE" > > > > All firmware and BIOS are up to date. I have other R630's with this same > NIC that I'm able to enable PXE boot. > > > > In the System Setup boot menu under Device Settings the two 10Gbit ports > aren't listed (which would allow me to enable them in boot order), however > the 1Gbit ports for the x520 are. > > > > 01:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ > Network Connection (rev 01) > > Subsystem: Dell Ethernet 10G 4P X520/I350 rNDC > > Flags: fast devsel, IRQ 44 > > Memory at 91d00000 (64-bit, non-prefetchable) [size=1M] > > I/O ports at 2020 [size=32] > > Memory at 91e04000 (64-bit, non-prefetchable) [size=16K] > > Expansion ROM at 92300000 [disabled] [size=512K] > > Capabilities: [40] Power Management version 3 > > Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ > > Capabilities: [70] MSI-X: Enable- Count=64 Masked- > > Capabilities: [a0] Express Endpoint, MSI 00 > > Capabilities: [e0] Vital Product Data > > Capabilities: [100] Advanced Error Reporting > > Capabilities: [140] Device Serial Number 36-a0-ff-ff-ff-9f-00-00 > > Capabilities: [150] Alternative Routing-ID Interpretation (ARI) > > Capabilities: [160] Single Root I/O Virtualization (SR-IOV) > > > > Any thoughts if there may be something in the BIOS that I'm missing that > is preventing the 2 x 10Gbit ports from being configurable in Device > Settings? > > > > Thanks, > > > > Mike > > > > _______________________________________________ > Linux-PowerEdge mailing list > [email protected] > https://lists.us.dell.com/mailman/listinfo/linux-poweredge > >
_______________________________________________ Linux-PowerEdge mailing list [email protected] https://lists.us.dell.com/mailman/listinfo/linux-poweredge
