No, I just do a reboot of the system.
What I do is take out a harddisk, wait for about 1 minute and see if the
deamon detects that there is a harddrive missing. When it does, I insert
another disk and wait for another minute till it is powered up. Then I
issue the rebuild command.
Maarten
"Leonard N. Zubkoff" wrote:
>
> Date: Fri, 26 Nov 1999 13:23:34 +0100
> From: vanliesh <[EMAIL PROTECTED]>
>
> I have the following configuration:
>
> Mainboard : Supermicro P6SBA
> Memory : 128MB SDRAM
> SCSI-controller : Symbios 875
> RAID-controller : Mylex eXtreme RAID DAC1164P
> Harddisk : 3 * Seagate Cheetah 9.1 Gb ST39102LW
>
> The Symbios SCSI-controller is used for the CD-rom, the three harddrives are
> configurated as RAID-5. I am using Redhat Linux 6.1. Everything works very
> well, but I cannot rebuild a harddrive without rebooting the server.
>
> This is an overview of the configuration messages:
>
> ***** DAC960 RAID Driver Version 2.2.4 of 23 August 1999 *****
> Copyright 1998-1999 by Leonard N. Zubkoff <[EMAIL PROTECTED]>
> Configuring Mylex DAC1164P PCI RAID Controller
> Firmware Version: 5.07-0-79, Channels: 2, Memory Size: 16MB
> PCI Bus: 2, Device: 8, Function: 0, I/O Address: Unassigned
> PCI Address: 0xFEAFFF80 mapped at 0xC4809F80, IRQ Channel: 5
> Controller Queue Depth: 128, Maximum Blocks per Command: 128
> Driver Queue Depth: 127, Maximum Scatter/Gather Segments: 33
> Stripe Size: 64KB, Segment Size: 8KB, BIOS Geometry: 255/63
> Physical Devices:
> 0:1 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJG6871700001934JHGM
> Disk Status: Online, 17782784 blocks
> 0:2 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJR02916000019460G8B
> Disk Status: Online, 17782784 blocks
> 0:3 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJH0426100001934JLXW
> Disk Status: Online, 17782784 blocks
> 0:7 Vendor: MYLEX Model: DAC1164P Revision: 0507
> Serial Number:
> 1:7 Vendor: MYLEX Model: DAC1164P Revision: 0507
> Serial Number:
> Logical Drives:
> /dev/rd/c0d0: RAID-5, Online, 35565568 blocks, Write Thru
>
> I ran into problems when trying to rebuild a failed drive (it is
> hot-swappable) .Then I waited for about 30 sec and put it back in. Then I
> issued the rebuild command. The following message appears:
>
> Rebuild of Physical Drive 0:2 Failed - Attempt to Rebuild Online or
> Unresponsive Drive
>
> There is a strange thing with the drive status: When I remove a harddisk, the
> status becomes critical and then DEAD.
> When I ask for the current status, it only shows
>
> 0:1 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJG6871700001934JHGM
> Disk Status: Online, 17782784 blocks, 8 resets
> 0:2 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJR02916000019460G8B
> 0:3 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJH0426100001934JLXW
> Disk Status: Online, 17782784 blocks, 8 resets
>
> The lack of a Disk Status line for that drive indicates that the controller no
> longer thinks that the drive is present in the configuration. I've never seen
> this sort of behavior. Perhaps it is a bug in the controller firmware. Please
> try the 5.07-0-07 firmware available from my web site and see if it exhibits
> this same behavior.
>
> As you can see, there is no diskstatus of drive 0:2 which is the drive I
> removed. When I reboot the machine the status is there again and shows
>
> 0:1 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJG6871700001934JHGM
> Disk Status: Online, 17782784 blocks,
> 0:2 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJR02916000019460G8B
> Disk Status: Dead, 17782784 blocks
> 0:3 Vendor: SEAGATE Model: ST39102LW Revision: 0006
> Serial Number: LJH0426100001934JLXW
> Disk Status: Online, 17782784 blocks,
>
> Now the status of drive 0:2 is DEAD and I can start a rebuild of drive 0:2.
>
> Rebuild of Physical Drive 0:2 Initiated
> Rebuild in Progress: Logical Drive 0 (/dev/rd/c0d0) 1% completed
> ....
> Rebuild in Progress: Logical Drive 0 (/dev/rd/c0d0) 97% completed
> Rebuild Completed Successfully
> Physical Drive 0:2 is now ONLINE
> Logical Drive 0 (/dev/rd/c0d0) is now ONLINE
>
> What can be the cause of this?? I don't want to reboot the server when a
> drive crashes, it should be possible to rebuild it online!
> It seems to me that the RAID-controller should scan the SCSI bus for new
> harddrives, even without doing a reboot.
>
> Agreed. Are you by any chance also power-cycling the drive when you reboot the
> system?
>
> Leonard
