The driver modifies platform data for internal purpose only. Fix that and make the platform data structure const.
Signed-off-by: Laurent Pinchart <[email protected]> Reviewed-by: Geert Uytterhoeven <[email protected]> --- drivers/tty/serial/sh-sci.c | 97 +++++++++++++++++++++++---------------------- 1 file changed, 49 insertions(+), 48 deletions(-) diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index ca68a7d562ea..4a54fd5909ed 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -114,7 +114,7 @@ struct sci_port { /* Platform configuration */ const struct sci_port_params *params; - struct plat_sci_port *cfg; + const struct plat_sci_port *cfg; unsigned int overrun_reg; unsigned int overrun_mask; unsigned int error_mask; @@ -420,41 +420,6 @@ static void sci_serial_out(struct uart_port *p, int offset, int value) WARN(1, "Invalid register access\n"); } -static int sci_probe_regmap(struct plat_sci_port *cfg) -{ - switch (cfg->type) { - case PORT_SCI: - cfg->regtype = SCIx_SCI_REGTYPE; - break; - case PORT_IRDA: - cfg->regtype = SCIx_IRDA_REGTYPE; - break; - case PORT_SCIFA: - cfg->regtype = SCIx_SCIFA_REGTYPE; - break; - case PORT_SCIFB: - cfg->regtype = SCIx_SCIFB_REGTYPE; - break; - case PORT_SCIF: - /* - * The SH-4 is a bit of a misnomer here, although that's - * where this particular port layout originated. This - * configuration (or some slight variation thereof) - * remains the dominant model for all SCIFs. - */ - cfg->regtype = SCIx_SH4_SCIF_REGTYPE; - break; - case PORT_HSCIF: - cfg->regtype = SCIx_HSCIF_REGTYPE; - break; - default: - pr_err("Can't probe register map for given port\n"); - return -EINVAL; - } - - return 0; -} - static void sci_port_enable(struct sci_port *sci_port) { unsigned int i; @@ -2539,9 +2504,50 @@ static int sci_init_clocks(struct sci_port *sci_port, struct device *dev) return 0; } +static const struct sci_port_params * +sci_probe_regmap(const struct plat_sci_port *cfg) +{ + unsigned int regtype; + + if (cfg->regtype != SCIx_PROBE_REGTYPE) + return &sci_port_params[cfg->regtype]; + + switch (cfg->type) { + case PORT_SCI: + regtype = SCIx_SCI_REGTYPE; + break; + case PORT_IRDA: + regtype = SCIx_IRDA_REGTYPE; + break; + case PORT_SCIFA: + regtype = SCIx_SCIFA_REGTYPE; + break; + case PORT_SCIFB: + regtype = SCIx_SCIFB_REGTYPE; + break; + case PORT_SCIF: + /* + * The SH-4 is a bit of a misnomer here, although that's + * where this particular port layout originated. This + * configuration (or some slight variation thereof) + * remains the dominant model for all SCIFs. + */ + regtype = SCIx_SH4_SCIF_REGTYPE; + break; + case PORT_HSCIF: + regtype = SCIx_HSCIF_REGTYPE; + break; + default: + pr_err("Can't probe register map for given port\n"); + return NULL; + } + + return &sci_port_params[regtype]; +} + static int sci_init_single(struct platform_device *dev, struct sci_port *sci_port, unsigned int index, - struct plat_sci_port *p, bool early) + const struct plat_sci_port *p, bool early) { struct uart_port *port = &sci_port->port; const struct resource *res; @@ -2578,13 +2584,9 @@ static int sci_init_single(struct platform_device *dev, sci_port->irqs[3] = sci_port->irqs[0]; } - if (p->regtype == SCIx_PROBE_REGTYPE) { - ret = sci_probe_regmap(p); - if (unlikely(ret)) - return ret; - } - - sci_port->params = &sci_port_params[p->regtype]; + sci_port->params = sci_probe_regmap(p); + if (unlikely(sci_port->params == NULL)) + return -EINVAL; switch (p->type) { case PORT_SCIFB: @@ -2804,7 +2806,7 @@ static char early_serial_buf[32]; static int sci_probe_earlyprintk(struct platform_device *pdev) { - struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev); + const struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev); if (early_serial_console.data) return -EEXIST; @@ -3095,10 +3097,9 @@ static int __init early_console_setup(struct earlycon_device *device, device->port.serial_out = sci_serial_out; device->port.type = type; memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port)); + port_cfg.type = type; sci_ports[0].cfg = &port_cfg; - sci_ports[0].cfg->type = type; - sci_probe_regmap(sci_ports[0].cfg); - sci_ports[0].params = &sci_port_params[sci_ports[0].cfg->regtype]; + sci_ports[0].params = sci_probe_regmap(&port_cfg); port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR); sci_serial_out(&sci_ports[0].port, SCSCR, SCSCR_RE | SCSCR_TE | port_cfg.scscr); -- Regards, Laurent Pinchart
