Hi Chris,
On Fri, Jan 13, 2017 at 3:44 PM, Chris Brandt <[email protected]> wrote:
> On Thursday, January 12, 2017, Geert Uytterhoeven wrote:
>> This is strange. There are two SDHI channels, but the STBCR12
>> documentation (all versions up to rev. 3.00) says the register has MSTP
>> bits for four SD host interfaces?
>>
>> Can you please enlighten me? Thanks!
>
> If you look in the rev 3.00 manual for RZ/A1H, in section
> "50.3.2 Card Detect/Write Protect", it says:
>
> * Power-Down mode at Card removal
> SD Host Interface module is halted by the MSTP123 bit to MSTP120 bit in
> Standby Control Register 12
> (STBCR12). If these bits of each channel in STBCR12 are set to 10, low
> power consumption is achieved at Card
> removal. See section 55, Power-Down Modes
>
>
> So, there are 2 clock sources for each SDHI channel, and the setting
> Options are:
> SD Host Interface 0 Module Stop
> 00: SD Host Interface 0 Module runs.
> 01: Setting prohibited.
> 10: Only card detect block in SD Host Interface 0 Module runs.
> 11: Clock supply to SD Host Interface 0 Module is halted
So typically you want to use 10 when idle, and 00 when active.
> Previously I've been running with '00' because I was turning EVERYTHING on
> in u-boot.
> Yesterday, I tested with just '10' and things seem to work OK
> for me.
>
> Since the sh_mobile_sdhi/tmio driver only allows for 1 clock per channel,
> '10' is my only choice for the DT.
>
> However, looking at a previous BSP for RZ/A1, the driver
> arch/arm/mach-shmobile/clock-r7s72100.c had this:
>
>
> static struct clk mstp_clks[MSTP_NR] = {
> [MSTP123] = SH_CLK_MSTP8(&peripheral1_clk, STBCR12, 3, 0), /* SDHI00
> */
> [MSTP122] = SH_CLK_MSTP8(&peripheral1_clk, STBCR12, 2,
> CLK_ENABLE_ON_INIT), /* SDHI01
> */
> [MSTP121] = SH_CLK_MSTP8(&peripheral1_clk, STBCR12, 1, 0), /* SDHI10
> */
> [MSTP120] = SH_CLK_MSTP8(&peripheral1_clk, STBCR12, 0,
> CLK_ENABLE_ON_INIT), /* SDHI11
> */
>
>
> But...that would make me think on boot it would be set to '01' (setting
> prohibited).
Yeah, running with enabled SDHI core and disabled card detect sounds silly.
> I'm going to try and find if "setting prohibited" really just means:
> "you can set it this way...but nothing is really going to work unless you
> enable the other clock".
>
> If that is the case, is there a DT equivalent to "CLK_ENABLE_ON_INIT" that
> I can do for MSTP120(SDHI11) and MSTP120(SDHI01) so they are both cleared
> on boot???
No there isn't. That's another reason why a full-fledged clock driver with
tables in C is a better idea than trying to describe all clocks in DT.
The new CPG/MSSR based driver (renesas-cpg-mssr.c) supports "critical
module clocks" through CLK_ENABLE_HAND_OFF. Unfortunately that flag hasn't
made it upstream, so I really should convert the driver to use the new
CLK_IS_CRITICAL instead...
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
