Hi Naman,
On 2017-08-23 00:15:41 +0530, Naman Jain wrote:
> Hi Niklas,
>
> adv7281m driver powers up the CSI transmitter in s_power(), which is
> called before setting up of D-PHY layer of R-Car CSI-2 Receiver.
> I shifted the part of code which enables CSI transmitter in adv7281m
> (Low Power state to High Speed state) to s_stream() -
>
> if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) {
> if (on) {
> adv7180_csi_write(state, 0xDE, 0x02);
> adv7180_csi_write(state, 0xD2, 0xF7);
> adv7180_csi_write(state, 0xD8, 0x65);
> adv7180_csi_write(state, 0xE0, 0x09);
> adv7180_csi_write(state, 0x2C, 0x00);
> if (state->field == V4L2_FIELD_NONE)
> adv7180_csi_write(state, 0x1D, 0x80);
> adv7180_csi_write(state, 0x00, 0x00);
> } else {
> adv7180_csi_write(state, 0x00, 0x80);
> }
> }
>
> After this change, i am not getting timeout of reading the phy clock
> lane and capture starts but nothing is displayed on the screen.
I know nothing about the adv7281m driver, but if you define DEBUG in the
rcar-vin and rcar-csi2 drivers it will provide you with a lot more
information about how they behave and maybe it can help you in your
troubleshooting. If you enable this and send me a console log of what
happens when you try to start a stream I can try and help you.
>
> On Wed, Jul 26, 2017 at 2:08 PM, Niklas Söderlund
> <[email protected]> wrote:
> > Hi Naman,
> >
> > On 2017-07-24 22:43:06 +0530, Naman Jain wrote:
> >> On Mon, Jul 24, 2017 at 3:11 PM, Niklas Söderlund
> >> <[email protected]> wrote:
> >> > Hi Naman,
> >> >
> >> > On 2017-07-24 14:30:52 +0530, Naman Jain wrote:
> >> >> i am using renesas soc with video decoder adv7281m
> >> >> i have done thr device tree configuration by following dt bindings
> >> >> i am getting timeout of reading the phy clock lane, after i start
> >> >> streaming
> >> >> and nothing is displayed on the screen
> >> >> kindly help me in configuration
> >> >
> >> > To be able to try and help you I would need a lot more information. For
> >> > starters:
> >> >
> >> > - Which kernel version are you using?
> >> >
> >> > - How dose the device tree nodes for VIN and ADV7281m look like?
> >> >
> >> > --
> >> > Regards,
> >> > Niklas Söderlund
> >>
> >> Hi Niklas,
> >>
> >> I am using kernel version - 4.9
> >
> > The VIN driver which supports CSI-2 and the R-Car CSI-2 driver is not a
> > part of the upstream kernel yet, and the latest patches with contains
> > the most fixes are based on newer kernels then v4.9. So I assume you are
> > using a BSP of some sort, if possible could you tell me which one?
> >
> > If you want to try with later increments of the VIN and CSI-2 patches
> > please see:
> >
> > http://elinux.org/R-Car/Tests:rcar-vin
> >
> >
>
> Soc version is rcar-h3 (r8a7795).
> Can tell me dependency patches required?
The dependencies are documented in the wiki page mentioned above, you
can also use the latest renesas-drivers master branch
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git
>
> >>
> >> following is the device tree configuration :
> >>
> >> &i2c6 {
> >> status = "okay";
> >> clock-frequency = <400000>;
> >> adv7281m@21{
> >> compatible = "adi,adv7281-m";
> >> reg = <0x20>;
> >> interrupt-parent = <&gpio6>;
> >> interrupts = <4 IRQ_TYPE_LEVEL_LOW>
> >> adv7281m_out: endpoint {
> >> clock-lanes = <0>;
> >> data-lanes = <1>;
> >> remote-endpoint = <&csi20_in>;
> >> };
> >> };
> >>
> >> }
> >>
> >> &csi20 {
> >> status = "okay";
> >> ports {
> >> #address-cells = <1>;
> >> #size-cells = <0>;
> >>
> >> port@0 {
> >> reg = <0>;
> >> csi20_in: endpoint {
> >> clock-lanes = <0>;
> >> data-lanes = <1>;
> >>
> >> virtual-channel-number=<0>;
> >
> > This is interesting for me, I have not worked with any driver for the
> > R-Car CSI-2 driver which understands the virtual-channel-number
> > property.
> >
> >> remote-endpoint =
> >> <&adv7281m_out>;
> >> };
> >> };
> >> };
> >> };
> >>
> >> &vin0 {
> >> status = "okay";
> >> };
> >>
> >> &vin1 {
> >> status = "okay";
> >> };
> >>
> >> &vin2 {
> >> status = "okay";
> >> };
> >>
> >> &vin3 {
> >> status = "okay";
> >> };
> >>
> >> &vin4 {
> >> status = "okay";
> >> };
> >>
> >> &vin5 {
> >> status = "okay";
> >> };
> >>
> >> &vin6 {
> >> status = "okay";
> >> };
> >>
> >> &vin7 {
> >> status = "okay";
> >> };
> >
> > --
> > Regards,
> > Niklas Söderlund
--
Regards,
Niklas Söderlund
