Re: [PATCH 4/6] media: rcar-vin: Handle CLOCKENB pin polarity

[Niklas Söderlund]

Hi Jacopo,

Thanks for your patch.

I'm happy that you dig into this as it clearly needs doing!

On 2018-05-16 18:32:30 +0200, Jacopo Mondi wrote:
> Handle CLOCKENB pin polarity, or use HSYNC in its place if polarity is
> not specified.
> 
> Signed-off-by: Jacopo Mondi <jacopo+rene...@jmondi.org>
> ---
>  drivers/media/platform/rcar-vin/rcar-dma.c | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c 
> b/drivers/media/platform/rcar-vin/rcar-dma.c
> index ac07f99..7a84eae 100644
> --- a/drivers/media/platform/rcar-vin/rcar-dma.c
> +++ b/drivers/media/platform/rcar-vin/rcar-dma.c
> @@ -123,6 +123,8 @@
>  /* Video n Data Mode Register 2 bits */
>  #define VNDMR2_VPS           (1 << 30)
>  #define VNDMR2_HPS           (1 << 29)
> +#define VNDMR2_CES           (1 << 28)
> +#define VNDMR2_CHS           (1 << 23)
>  #define VNDMR2_FTEV          (1 << 17)
>  #define VNDMR2_VLV(n)                ((n & 0xf) << 12)
>  
> @@ -691,6 +693,15 @@ static int rvin_setup(struct rvin_dev *vin)
>               dmr2 |= VNDMR2_VPS;
>  
>       /*
> +      * Clock-enable active level select.
> +      * Use HSYNC as enable if not specified
> +      */
> +     if (vin->mbus_cfg.flags & V4L2_MBUS_DATA_ACTIVE_LOW)
> +             dmr2 |= VNDMR2_CES;
> +     else if (!(vin->mbus_cfg.flags & V4L2_MBUS_DATA_ACTIVE_HIGH))
> +             dmr2 |= VNDMR2_CHS;

After studying the datasheet for a while I'm getting more and more 
convinced this should be (with context leftout in this patch context) 
something like this:

        /* Hsync Signal Polarity Select */
        if (!(vin->mbus_cfg.flags & V4L2_MBUS_HSYNC_ACTIVE_LOW))
                dmr2 |= VNDMR2_HPS;

        /* Vsync Signal Polarity Select */
        if (!(vin->mbus_cfg.flags & V4L2_MBUS_VSYNC_ACTIVE_LOW))
                dmr2 |= VNDMR2_VPS;

        /* Clock Enable Signal Polarity Select */
        if (!(vin->mbus_cfg.flags & V4L2_MBUS_DATA_ACTIVE_LOW))
                dmr2 |= VNDMR2_CES;

        /* Use HSYNC as clock enable if VIn_CLKENB is not available. */
        if (!(vin->mbus_cfg.flags & (V4L2_MBUS_DATA_ACTIVE_LOW | 
V4L2_MBUS_DATA_ACTIVE_HIGH)))
                dmr2 |= VNDMR2_CHS;

Or am I misunderstanding something?

> +
> +     /*
>        * Output format
>        */
>       switch (vin->format.pixelformat) {
> -- 
> 2.7.4
> 

-- 
Regards,
Niklas Söderlund