Hi Simon,
On Tue, May 22, 2018 at 10:10 PM, Simon Horman <ho...@verge.net.au> wrote:
> On Mon, May 21, 2018 at 11:45:01PM +0900, Magnus Damm wrote:
>> From: Magnus Damm <damm+rene...@opensource.se>
>>
>> Add IPMMU device nodes for the R-Car V3H SoC aka r8a77980.
>>
>> The r8a77980 IPMMU is quite similar to r8a77970 however VC0
>> has been added. The IMSSTR bit assignment has also been
>> reworked. Power domains are also quite different however the
>> the documentation is rather unclear about this topic.
>>
>> Until we know better VC0 gets assigned to R8A77980_PD_ALWAYS_ON.
>>
>> Signed-off-by: Magnus Damm <damm+rene...@opensource.se>
>> ---
>>
>> Developed on top of renesas-devel-20180518-v4.17-rc5
>>
>> arch/arm64/boot/dts/renesas/r8a77980.dtsi | 49
>> +++++++++++++++++++++++++++++
>> 1 file changed, 49 insertions(+)
>>
>> --- 0001/arch/arm64/boot/dts/renesas/r8a77980.dtsi
>> +++ work/arch/arm64/boot/dts/renesas/r8a77980.dtsi 2018-05-21
>> 22:31:52.460607110 +0900
>> @@ -387,6 +387,55 @@
>> dma-channels = <16>;
>> };
>>
>> + ipmmu_ds1: mmu@e7740000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xe7740000 0 0x1000>;
>> + renesas,ipmmu-main = <&ipmmu_mm 0>;
>> + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
>> + #iommu-cells = <1>;
>> + };
>> +
>> + ipmmu_ir: mmu@ff8b0000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xff8b0000 0 0x1000>;
>> + renesas,ipmmu-main = <&ipmmu_mm 3>;
>> + power-domains = <&sysc R8A77980_PD_A3IR>;
>> + #iommu-cells = <1>;
>> + };
>> +
>> + ipmmu_mm: mmu@e67b0000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xe67b0000 0 0x1000>;
>> + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
>> + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
>> + #iommu-cells = <1>;
>> + };
>> +
>> + ipmmu_rt: mmu@ffc80000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xffc80000 0 0x1000>;
>> + renesas,ipmmu-main = <&ipmmu_mm 10>;
>> + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
>> + #iommu-cells = <1>;
>> + };
>> +
>> + ipmmu_vc0: mmu@fe6b0000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xfe6b0000 0 0x1000>;
>> + renesas,ipmmu-main = <&ipmmu_mm 12>;
>> + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
>> + #iommu-cells = <1>;
>> + };
>> +
>> + ipmmu_vi0: mmu@febd0000 {
>> + compatible = "renesas,ipmmu-r8a77980";
>> + reg = <0 0xfebd0000 0 0x1000>;
>> + renesas,ipmmu-main = <&ipmmu_mm 14>;
>> + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
>> + #iommu-cells = <1>;
>> + };
>> +
>
> nit: I believe the IPMMU nodes should go above the AVB rather than the
> MMC node to preserve the current node sorting order of:
>
> 1) bus address
> 2) IP block
> 3) alphabetical
Will reposition the IPMMU nodes in next version. Will also add vip0
and vip1 IPMMU nodes as described in the 1.0 data sheet.
Thanks,
/ magnus
