Hi Jacopo, Thank you for the patch.
On Wednesday, 5 September 2018 18:29:45 EEST Jacopo Mondi wrote: > Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board. > > Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked > to the SoC CSI-2 receiver port. > > Signed-off-by: Jacopo Mondi <[email protected]> Reviewed-by: Laurent Pinchart <[email protected]> > --- > arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 86 +++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > > diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts > b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts index 2bc3a48..d2faf3e > 100644 > --- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts > +++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts > @@ -28,6 +28,29 @@ > /* first 128MB is reserved for secure area. */ > reg = <0x0 0x48000000 0x0 0x38000000>; > }; > + > + cvbs-in { > + compatible = "composite-video-connector"; > + label = "CVBS IN"; > + > + port { > + cvbs_con: endpoint { > + remote-endpoint = <&adv7482_ain7>; > + }; > + }; > + }; > + > + hdmi-in { > + compatible = "hdmi-connector"; > + label = "HDMI IN"; > + type = "a"; > + > + port { > + hdmi_in_con: endpoint { > + remote-endpoint = <&adv7482_hdmi>; > + }; > + }; > + }; > }; > > &avb { > @@ -47,6 +70,22 @@ > }; > }; > > +&csi40 { > + status = "okay"; > + > + ports { > + port@0 { > + reg = <0>; > + > + csi40_in: endpoint { > + clock-lanes = <0>; > + data-lanes = <1 2>; > + remote-endpoint = <&adv7482_txa>; > + }; > + }; > + }; > +}; > + > &ehci0 { > status = "okay"; > }; > @@ -55,6 +94,49 @@ > clock-frequency = <48000000>; > }; > > +&i2c0 { > + status = "okay"; > + > + video-receiver@70 { > + compatible = "adi,adv7482"; > + reg = <0x70>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&gpio0>; > + interrupt-names = "intrq1", "intrq2"; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>, > + <17 IRQ_TYPE_LEVEL_LOW>; > + > + port@7 { > + reg = <7>; > + > + adv7482_ain7: endpoint { > + remote-endpoint = <&cvbs_con>; > + }; > + }; > + > + port@8 { > + reg = <8>; > + > + adv7482_hdmi: endpoint { > + remote-endpoint = <&hdmi_in_con>; > + }; > + }; > + > + port@a { > + reg = <0xa>; > + > + adv7482_txa: endpoint { > + clock-lanes = <0>; > + data-lanes = <1 2>; > + remote-endpoint = <&csi40_in>; > + }; > + }; > + }; > +}; > + > &ohci0 { > status = "okay"; > }; > @@ -94,6 +176,10 @@ > status = "okay"; > }; > > +&vin4 { > + status = "okay"; > +}; > + > &xhci0 { > pinctrl-0 = <&usb30_pins>; > pinctrl-names = "default"; -- Regards, Laurent Pinchart
